How to tune up 3 cylinder engine tractor&marine mechanic
Пікірлер: 161
@onthatdove2 жыл бұрын
I appreciate your repetition. It helped me learn how to do this for the first time.
@tractorsmarinemechanic2 жыл бұрын
Thank you.just remember TWO OPEN VALVE which is the intake and exhaust valves and the remaining cylinder is on TOP then apply valve setting.pls.share and subscribe.thank you
@richceglinski75432 жыл бұрын
Very good instructional video for easy to understand way to determine piston position /stroke to set valve clearance. You speak at a pace slow enough to comprehend things as they're being said and recap at the end. Best video I found on the topic. Thank You.
@tractorsmarinemechanic2 жыл бұрын
Thank you for your comments and watching. please subscribe,share and hits like.thank you.
@williamoeddinsjr8257 Жыл бұрын
Thank u for putting video out there best understanding video ever
@tractorsmarinemechanic Жыл бұрын
Thank you.please like,share and subscribe.
@bernardomondi4704 Жыл бұрын
How do you replace valve seals without the valves dropping down on the pistion chamber
@MrmachineELF2 жыл бұрын
You sir are a legend 👍🏼
@clinton5511 Жыл бұрын
Awesome and clear video just waiting for it starting
@tractorsmarinemechanic Жыл бұрын
Thank you for watching
@JH-zy1dj Жыл бұрын
Just subscribed! Thank you very much!
@tractorsmarinemechanic Жыл бұрын
Salamat.
@joeb4382 Жыл бұрын
Awesome tip! Many thanks for your video!
@tractorsmarinemechanic Жыл бұрын
Thank you for watching
@joeb4382 Жыл бұрын
Just subscribed. Looking forward to learning more from you
@tractorsmarinemechanic Жыл бұрын
Thank you and also for watching
@bernardomondi4704 Жыл бұрын
Instructions very clear well explained
@tractorsmarinemechanic Жыл бұрын
Thank you for watching.subscribe,share,and like.also follow my fb tractors and marine mechanic.ty
@findvoltage Жыл бұрын
what a great chanel. hello from AU
@tractorsmarinemechanic Жыл бұрын
Thank for watching.what is AU?
@angelopaulo1187 Жыл бұрын
Great videos.......danke
@DIY_Farmer3 жыл бұрын
keep up the good work sir
@tractorsmarinemechanic3 жыл бұрын
Salamat.
@MrToluen603 жыл бұрын
Thanks from France. Very interesting.
@tractorsmarinemechanic3 жыл бұрын
Pls share it and thank you for watching.
@kangatharan8829 Жыл бұрын
Super bro thanks and congrats very good works bro
@tractorsmarinemechanic Жыл бұрын
Thank you for watching
@abdullahjawad3251Ай бұрын
Beautiful teaching I like this bro
@tractorsmarinemechanicАй бұрын
Kindly share and like...thank you.
@alatberat992 жыл бұрын
good job brather
@tractorsmarinemechanic2 жыл бұрын
Thank you for watching.please subscribe,share and also hits like.salamat
@pavlo5877 Жыл бұрын
Thank you very much
@tractorsmarinemechanic Жыл бұрын
Thank you too for watching.
@bernardomondi4704 Жыл бұрын
Vakve adjustment cool
@bsai8502 Жыл бұрын
Thank you bro
@tractorsmarinemechanic Жыл бұрын
Thank you also for watching
@gordonsprocketwilmot41423 жыл бұрын
Great videos! My engine does not have the nut and screw to adjust the tappets can you tell me what to do in this instance please
@tractorsmarinemechanic3 жыл бұрын
Some other engine for the automotive is the same with your engine.no need to tune up.thank for watching for my video I hope you learned something.thanks pls.subscribe and share.
@AsmaKhan-dr5ph Жыл бұрын
Thanks bro
@tractorsmarinemechanic Жыл бұрын
Thank you for watching
@hamisimlowea1259 Жыл бұрын
I have seen the valve adjustment for a three cylinder engine how will I it be with a four cylinder engine ? Please let me know especially the v243_combine engines
@tractorsmarinemechanic Жыл бұрын
kzfaq.info/get/bejne/btR-ZJlym5nclGg.html Please try to watch at the above videos.
@darleneaparicio9852 Жыл бұрын
❤❤❤❤
@Sparisland3 жыл бұрын
I have a Yanmar 3 cyl engine that looks very similar. Because there is no spring to hold it, the exhaust valve on cylinder 3 has side to side movement of .032" so the lifter is not always centered on the valve cap. It makes noise and the valve clearance clearance is different if it is moved from one side to the other. Can I shim the gap between the snap ring and the lifter to keep it centered on the valve? If I use a .025 shim, it will leave .007 clearance, is that sufficient?
@tractorsmarinemechanic3 жыл бұрын
Shim or or washer
@Sparisland2 жыл бұрын
@@tractorsmarinemechanic Yeah, Shimmed it. Already have 10 hours on it and it's great. Thanks.
@ChansocheathChuon Жыл бұрын
Could you show How to adjust valves on Mitsubishi MT14D ? Thank 🙏
@tractorsmarinemechanic Жыл бұрын
Thank you for watching.please subscribe like and share. actually they both the same on how to adjust valve tappet clearance but I will do as per your request.
@user-ij9vo2gz8e4 ай бұрын
For Hinomoto c174(engine toyosha cs100, 3 cylinder) is same?which is clearance for intake valves and exhaust valves?are you selling engine parts for this tractor?
@tractorsmarinemechanic4 ай бұрын
Same...I'm just a mechanic I do not selling engine or parts.thank you for watching
@user-ij9vo2gz8e4 ай бұрын
@@tractorsmarinemechanic thanks.what is the clearance for the valves?
@carolyneddleman93674 ай бұрын
My yanmar diesel 3t72sb engine will not move the valves like yours does its different when doing the first set of valves sny help will greatly appreciated
@tractorsmarinemechanic4 ай бұрын
What do you mean ?YANMAR engine is different from Kubota.
@carolyneddleman93674 ай бұрын
@@tractorsmarinemechanic when I go to set the number 1 cylinder the 3 and 6 valve don't open
@tractorsmarinemechanic4 ай бұрын
Ok...I will teach you.if you don't know the firing order just follow me and I repeat how to set the valve setting rotate your engine to the right and observe the valve.THERE ARE TWO VALVES WILL BE OPEN and remaining cylinder is on the top and apply valve tappet clearance.(TWO VALVES must be FULLY OPEN) example:if the valves from cyli.#1&2 are open the top is cyl.#3. after cyl.3 just rotate again the engine same action of the valve.you can observe the exhaust valve from cyl.#3 to be fully open and you can see the intake valve from other cylinder is also fully open.the remaining one is on the top to apply tappet clearance.The same on next cylinder.ithank you for watching.i hope will.you understand.
@marekcibulka25733 жыл бұрын
Hi, my tractor iseki 237 landhope have motor isuzu e3ag1 1,429l and how tappet clearance for that engine. Thanks.
@tractorsmarinemechanic3 жыл бұрын
Thank for watching. Just applied o.14 in your feeler gauge.
@tractorsmarinemechanic3 жыл бұрын
Pls.subscribe and share. thank you
@vovaborovitskij28063 жыл бұрын
Enjin 3 t 82 v - n barubu no bakku rasshu. Arigatō
@sumanmondalsuman76353 жыл бұрын
Thanks you very much 👍👍👍❤️❤️❤️
@tractorsmarinemechanic3 жыл бұрын
Pls. share hit like.thank also.
@sumanmondalsuman76352 жыл бұрын
@@tractorsmarinemechanic Ook sir 4 cylinder engine tapped stating video
@grb318 Жыл бұрын
👍👍👍👍
@tractorsmarinemechanic Жыл бұрын
Thank you for watching
@omleejason52102 жыл бұрын
Afternoon sir .....I did put a top gasket on my Kubota ....than it run for about a week but it started to leak oil between the cylinder head and the block again .....does that mean I did not torch it's properly ...or what sir
@tractorsmarinemechanic2 жыл бұрын
Yes sir...
@omleejason52102 жыл бұрын
@@tractorsmarinemechanic so that mean I can just retorch it again ...
@eduardsonchavez94912 ай бұрын
Maybe you dont put the one oring for oil line in cylinder head gasket sir???
@agusidah6582 жыл бұрын
what is the size of the master cylinder head bolt moment?
Boss baka pwede nio gawan ng video pano palitan oilseal ng monroematic ng l1 sunshine?
@tractorsmarinemechanic3 жыл бұрын
Alin pong oil seal or saan parte?may mga video n po sa mga sunshine.hapin nyo n lng po sa playlist
@fourbromechanicvlog41052 жыл бұрын
boss pareho lang ba pag tune up ng komatsu 3cylinder pc20 yan
@tractorsmarinemechanic2 жыл бұрын
Pareho lng po yn sir.khit n anong URI ng 3cylinder n makina.
@user-ISEKI3 жыл бұрын
Valve-tappet clearance iseki engine e3ae1 /1296cm. ---is thees 02/02 ---??? Or not??? Iseki landhope tu 197 f.
@tractorsmarinemechanic3 жыл бұрын
The same with Kubota.
@arneloberes62732 жыл бұрын
Boss yong sabi mo na two open valves din apply valve clearance na confused ako?saan ka dapat hihinto sa sa pag ikot ng crankshaft mo na masasabi na tama na e adjust yong remaining cylinder?
@tractorsmarinemechanic2 жыл бұрын
dalawang valve Ang mag open,Isang INTAKE VALVE at Isang EXHAUST VALVE at Ang natitirang cylinder ay Ang naka top at mag mag apply kn ng valve setting.hihinto k hangang bumaon Ang valve.
@jay-arates39312 жыл бұрын
Hello po mga sir,,,pwedi po ba magtanong tungkol sa valve tappet clearance intake and exhaust ng D950 Kubota engine 3 cylinder?salamat
@tractorsmarinemechanic2 жыл бұрын
Ano po b Ang tanong nyo?
@dickturpin2719 Жыл бұрын
Thx mate
@tractorsmarinemechanic Жыл бұрын
You can see Tractors and marine mechanic on fb
@johncena81892 жыл бұрын
is it the same if the diesel engine is deutz marine diesel engine 3 cylinders?
@tractorsmarinemechanic2 жыл бұрын
Same
@johncena81892 жыл бұрын
@@tractorsmarinemechanic Thank you Sir.
@j.jacobson2 жыл бұрын
Yanmar 3 cylinder .0010 as well and same procedure ?
@tractorsmarinemechanic2 жыл бұрын
All 3 cylinder engine is the same procedure
@Harrybollox2 жыл бұрын
@@tractorsmarinemechanic not quite. My Westerbeke is 1,3,2 firing order. Great video though
@lorgenefelipe943311 ай бұрын
Sir normal lang po ba na may langis sa part ng flywheel? Meron kasi tumatagas sa amin na langis galing sa flywheel.
@tractorsmarinemechanic11 ай бұрын
Hindi po normal.ano po unit?pwd k po tumawag sa #09502423351
@3sisters6842 жыл бұрын
Surplus parts
@agusidah6582 жыл бұрын
What clirens in ,eks master
@tractorsmarinemechanic2 жыл бұрын
0.25mm.thank you for watching.please subscribe,share and like.salamat
@karansharma-ot7hm2 жыл бұрын
Sir I m maknik
@tractorsmarinemechanic2 жыл бұрын
Thank you for watching.please share my videos and also subscribe.
@user-wx6wq9eg2z5 ай бұрын
Ano po yong size ng feeler gauge boss 4:02
@abebayehubelayneh66772 жыл бұрын
please write to me the valve clearance of yanmar 3tnv 82 -DSA
@tractorsmarinemechanic2 жыл бұрын
0.25mm
@jecxsonbravo25682 жыл бұрын
Boss pano tanggalin impeller ng water pump nyan? Sira na ksi yung bearing sakin. May thread ba ung impeller at shafting nya? O pinipress lng pra matanggal?
@tractorsmarinemechanic2 жыл бұрын
Sir paki click n lang po Yong profile picture ng channel ko tapos click mo video at hanapin mo po Kung paano ako magpalit ng bearing ng water pump.salamat sa panood.pls subscribe and share salamat.
@jecxsonbravo25682 жыл бұрын
@@tractorsmarinemechanic ok sir. Salamat. Nka subscribe ndin ako. San po ba shop nyo? Matanong ko ndin po ano problema pag naghahalo engine oil at transmission oil?
@tractorsmarinemechanic2 жыл бұрын
Sira Ang oil seal ng hydraulic pump mo.
@jecxsonbravo25682 жыл бұрын
Last na sir, narerepair ba control valve sir pra sa rotovator? Pano masasabi na sira control valve? Gusto ko lng mrestore yung unit ko
@tractorsmarinemechanic2 жыл бұрын
Tingnan natin sir Kung sira n b talaga or hindi.saan po loc?
@brynethpasco50322 жыл бұрын
Sir same lng po ba sila pag tune up sa engine na D950? Same lng po ba ng filler gauge at firing order?
@tractorsmarinemechanic2 жыл бұрын
Pareho lang lahat ng 3 cylinder
@brynethpasco50322 жыл бұрын
@@tractorsmarinemechanic salamat po
@marciohenriquelacerda42012 жыл бұрын
Me ajudou muito em
@tractorsmarinemechanic2 жыл бұрын
Thank you for watching.pls.subscribe and share
@divemasterkervie80562 жыл бұрын
Magaling sir nagets ko na din kse sa tatay ko tumitingin lng ako hndi ko makuha kung pano nya itune up ang d850 namin tinatanggal nya ang glow plug at tinatapat nya sa butas ang daliri nya di ko din sure kung tama ba yon...slmat sa tutorial sir
@tractorsmarinemechanic2 жыл бұрын
Salamat din sa panonood.pki share naman po.salamat
@divemasterkervie80562 жыл бұрын
Share ko yan sir,salamat sa pgshare...
@divemasterkervie80562 жыл бұрын
Sa fb lng pla pwede ishare sir nashare ko na di pala maishare dto sa youtube
@cristianquiroel52322 жыл бұрын
Sir ano po yung running mate nya?
@tractorsmarinemechanic2 жыл бұрын
3clinder Yan sir kaya walang running mate.ang may running mate ay Ang even numbers,gaya ng 4,6,8,12,16,18 Yan po Ang may mga running mate
@mostafaelsayed9716 Жыл бұрын
Whare are you frome sir
@tractorsmarinemechanic Жыл бұрын
Philipines
@prasetyalewang8195 Жыл бұрын
please write to me the valve clearance yanmar 3tnv84 .. terima kasih
@tractorsmarinemechanic Жыл бұрын
Just give 0.25mm
@edgardomarteriz44392 жыл бұрын
Sana tinagalog nalang ndi kapa nahihirapan
@user-nc5bb8mg1r Жыл бұрын
Sir parihas ba ang ganyang procedure sa 3 cylinder na deuts
@tractorsmarinemechanic Жыл бұрын
Kahit na anong 3cylinder po
@tractorsmarinemechanic Жыл бұрын
Salamat po sa panonood.pasubscribe nmn po share and like.salamat po
@user-nc5bb8mg1r Жыл бұрын
Ok sir salamat
@gregoriotigon7066 Жыл бұрын
1501 Kubota sir ano clearance?
@tractorsmarinemechanic Жыл бұрын
Pareho lang po Dyan..25mm lang nilalagay ko
@gregoriotigon7066 Жыл бұрын
@@tractorsmarinemechanic salamat sir
@3sisters6842 жыл бұрын
Sir, nagbibinta rin ba kayo ng kubota engine spare parts?
@tractorsmarinemechanic2 жыл бұрын
Opo mam.ano po n parts Ang kailangan nyo?
@3sisters6842 жыл бұрын
@@tractorsmarinemechanic valve seat for kubota D950 po sir.
@3sisters6842 жыл бұрын
@@tractorsmarinemechanic cylinder head for kubota D950 magkanu po sir?
@tractorsmarinemechanic2 жыл бұрын
Baka po valve seal.kung sira po Ang valve seat nyo,ipa machine nyo sa Isang machine shop.
@3sisters6842 жыл бұрын
@@tractorsmarinemechanic sir magkanu po binta nyo pagbibili ako ng buong cylinder head?
@tewodrosabera42832 жыл бұрын
፨፨፨፨
@karansharma-ot7hm2 жыл бұрын
Sorry for eangish iam India🇮🇳
@tractorsmarinemechanic2 жыл бұрын
Salamat/thank you
@karansharma-ot7hm2 жыл бұрын
Sir please job tractor mechenic
@user-ISEKI3 жыл бұрын
Hi .please sais klearens too waive iseki engine e3ae1./1296 cm. Iseki landhope tu 197f ---1---3---2 ... Sorry for eanglish .i am ukraine...
@tractorsmarinemechanic3 жыл бұрын
Your engine is Isuzu.Valve tappet clearance for that engine you can apply 12 or 14 in your feeler gauge.thank you pls subscribe and share.
@user-ISEKI3 жыл бұрын
@@tractorsmarinemechanic tank yuo veary mach. I dont stand...inlet valve 0.12 ... Exhaust valve 0.14 ...or all 0.12--0.14.. engine e3ae1----1-3-2???
@tractorsmarinemechanic3 жыл бұрын
Intake and exhaust apply 0.14
@user-ISEKI3 жыл бұрын
@@tractorsmarinemechanic ok .thank yuo very mach.yuo is the beast mechanikal master👍👋. Good like...