35 MPH Razor MX500 or MX650 for $420 - Tesla Inspired Dirt Bike
Рет қаралды 136,427
Күн бұрынLink to products used in video: amzn.to/3O8XeaM This is full length DIY video on how to upgrade your Razor MX500 or MX650 for around $400. This is a Tesla inspired bike, only the decal's are Tesla. #teslaDirtBike #tesla1800w #teslaminibike All products used listed below:
48V / 14Ah Li-ion battery (20Ah for longer ride time): amzn.to/43gniXw or
s.click.aliexpress.com/e/_mNV...
48V 1800W or 2000W motor kit: amzn.to/48YJd7k or amzn.to/4dVmg8o
13T 25H motor sprocket amzn.to/4ax9Ukh
Hydraulic Brakes (front & rear): amzn.to/3RN0acN
Brake Rotors (48mm bolt pattern): amzn.to/3LmX7Wi
Yellow Junction Box: amzn.to/4c4rvRI
(optional) 3 speed throttle: amzn.to/3LnNUgi
(optional) Scott Grips: amzn.to/3BqFCzN
(optional) CRF50 Plastics (Red & White): amzn.to/3QCkGLH
(optional) 25H Chain (thicker links) is optional: amzn.to/3dBOR4D
(optional) Headlight: amzn.to/3UjCoXE
(optional) Handlebar switch: amzn.to/3LeCsUh
(optional) Tesla Decals (small): amzn.to/3eCOU3W
(optional) Tesla Decal (large) with big "T": amzn.to/3K5op3O
(optional) Electrical Connectors: amzn.to/3Sh8v8f
(optional) Crimper Tool: amzn.to/3UvOpcC
(optional) Solder & Seal Connectors: amzn.to/2WcCQNZ
(optional) Heat Gun : amzn.to/39HAABD
(optional) Lever Wire Connectors (east to use): amzn.to/39BuYZy
(optional) Stepdown transformer (48V to 12V): amzn.to/3eZzmrj
(Optional) 4” motor heat sink: ebay.us/qY6S2z
Velcro straps amzn.to/3ZCOpcH
.
Chapters
0:00 - Intro
0:36 - Disassemble
1:13 - Connect & Test motor kit & battery
8:11 - Modification to motor
12:08 -Battery connection to controller
12:33 - Installing Battery into the frame
15:25 - connecting the 3 speed throttle
22:10 - Install hydraulic brakes
27.10 - Install new grips
28:57 - Wiring on/off switch; headlight and LED lights.
33:26 - Conclusion
razor.com/products/electric-r...
razor.com/products/electric-r...
razor.com/products/electric-r...
razor.com/products/electric-r...
razor.com/products/electric-r...
www.walmart.com/c/kp/razor-di...
FTC: Products linked above use income earning auto affiliate links, which means that if you click one of the links and purchase a products, I could receive a very small commission (at no additional cost to you).
@Dareal_dave Жыл бұрын
This is the best tutorial video i ever saw. i watched so many and they skipped the 2 steps you showed. THANK YOU.
@BRichSolution Жыл бұрын
Glad I could help others out. Have fun riding your bike
@SuperSickNerd 6 ай бұрын
Can you use the mx350 ? Mine goes 23mph. I want to upgrade my 3rd one.
@imwiththebusiness Жыл бұрын
subscribed for giving us something short, sweet, into detail and a cheap alternative.
@BRichSolution Жыл бұрын
Glad I can help other razor owners out
@maukaman Жыл бұрын
I like using brass brads (the ones for binding papers) as bridges for testing, and sometimes long for long term. They slide in perfectly and stay tight
@BRichSolution Жыл бұрын
Great idea
@tomp2636 8 ай бұрын
Great video. I just received all the parts and giving them to my son for Christmas. He has been wanting this setup for a couple years but I was hesitant about doing it. Thank you for a very easy to follow video. We have 2 bikes and eventually we will do both.
@BRichSolution 8 ай бұрын
Glad I could help
@maxlewin7807 Жыл бұрын
I have to say I am very impressed. Some other guy made a guide to adding a 50cc without welding anything and it was a clean build - but prob spent way more than you guys. Plus this just shows skill. Very cool.
@BRichSolution Жыл бұрын
In burbs electric is must as gas will annoy neighbors
@landisburnett6035 Жыл бұрын
Thanks Rich! you are single handedly helping me make decisions to get a bike And on the road! For Best Bang for my buck!
@BRichSolution Жыл бұрын
Glad I could help other people out
@poison_ivy8279 11 ай бұрын
Wow, i’ve been looking for a tutorial for ever to help me because i’m new to this stuff, thank you so much!
@BRichSolution 11 ай бұрын
Glad it was helpful
@sunnyhillestate1 7 ай бұрын
Thanks for the detailed video, DUE TO THIS QUALITY VIDEO..I HAVE SUBSCRIBED!!
@BRichSolution 7 ай бұрын
Thank you
@CristianCiobanu-plus Жыл бұрын
Thank you for making such a detailed step-by-step tutorial.
@BRichSolution Жыл бұрын
Glad it can help othets
@kexrm6887 Жыл бұрын
@@BRichSolution where do you connect the voltage meter yellow wire from the throttle?
@TheMrjetdoc35 Жыл бұрын
Awesome video. Subscribed! Thanks for all the links.
@BRichSolution Жыл бұрын
Glad it helped you out
@thekidwitdaonetwunyfive 3 ай бұрын
Thank you so much. Better video than any other tutorial.
@BRichSolution 3 ай бұрын
Glad it helped and reason why I made the video
@Idolikethis 11 ай бұрын
Thank you so much for doing this!!!
@BRichSolution 11 ай бұрын
I’m glad I can help other owners out
@stevusbeefus Жыл бұрын
used this guide to build mine and it works great, thx man
@BRichSolution Жыл бұрын
Glad I could help others out as that was my intention
@jingostanklong1265 Жыл бұрын
How long did this take to build?
@stevusbeefus Жыл бұрын
@@jingostanklong1265 about 6 hours to strip it and install the new motor, controller, and battery (along with the throttle), and probably spent another like 12 hours installing brakes, plastics, rotor disks, keyswitch, etc
@Diegosconfused 11 ай бұрын
Best budget razor vid ive ever seen
@BRichSolution 11 ай бұрын
Thanks man
@bluethumbdiy4735 Жыл бұрын
Great video! Did you have to tap new threads to mount the new motor? I can't quite tell what you did from the video. I've head that the spacing is wider on newer motors. I've also heard that the 1000W or greater motors don't have recessed bolts.
@BRichSolution Жыл бұрын
New rotors bolts same thread as stock threads. No drill or tap required…bolts right on. As for the motor 2 screws need to be recessed as show in my video. If you buy more expensive kits the bolts will be recessed
@camdenbailey3185 Жыл бұрын
I have a 3kw motor, same vevor kit. I'm using overboard batteries and xt60 adapters to splice everything together. I'll eventually buy a solder kit and actually wire the batteries correctly. This all is going on a mx650. I'll be drilling holes in the frame because of those screws. I'm kinda new to all this, so I hope I don't mess anything up.
@BRichSolution Жыл бұрын
I would not drill holes in the frame especially with 72V / 3000W; recess the 2 screws in the motor see video 8:00 mark
@TURBOMOOSE Жыл бұрын
Sounds familiar..... is this who I think it is lmao??
@TURBOMOOSE Жыл бұрын
As B rich mentioned, unscrew the bolt, recess the screw head on the plate and repeat for the other two just in case you need to play with fitment. The screws will then sit flush and you can cut, grind or leave (if you have clearance) the extended screw ends off the opposite end.
@hibby5793 Жыл бұрын
Great vid, I was planning to try this out and follow your video but was wondering if you could just use a standard drill bit to recess the screw holes or do you need a special one.
@BRichSolution Жыл бұрын
Yes, standard drill bit it what i used. The aluminum drills out very easy.
@Razor.racing Жыл бұрын
What size drill bit did you use and what happens when you recess it , is it just making the hole deeper ?
@andrewnick9895 Жыл бұрын
Love your videos. I already over-volted my son's MX650 to a 48V 20Ah lithium linked in another of your videos. Also installed lights thanks to your help. Considering getting him this motor and controller for Christmas. Any issues running the 1800W motor with the ebay battery rated for 1200W? The 35A 20Ah I got is rated for 1500W, but still under the wattage of this motor. Thanks again for sharing all this great content!
@BRichSolution Жыл бұрын
No issues running 48v with 1800w motor kit. I believe the battery bms states 30amp but its more like 40A as i see no degrade in performance until voltage drops below 45V so that tells me 1800w / 45V = 40Amps
@Michael_2211 4 ай бұрын
Fantastic tutorial, planning on doing this but I was curious if you used the same chain as the stock one ( length wise ), sorry if I missed you saying it. Please let me know asap, thanks!
@BRichSolution 4 ай бұрын
Yes, correct use stock chain
@aaronrain9077 11 ай бұрын
awesome video, thanks for doing this. sub'd!
@BRichSolution 11 ай бұрын
Thanks for feedback and glad I could help others out
@jamesobrien6855 Жыл бұрын
I wrapped the whole battery up in that foam and wrapped it up good with duct tape. So basically it is covered all the way around with 1/2 of that foam that came in the box and completely wrapped and sealed in duct tape. What do you think? Could it possibly get to hot and maybe catch fire or blow up? Thanks.
@BRichSolution Жыл бұрын
I left some of the ends open to vent and breath a little
@RHauto 10 ай бұрын
Hey man, great video, it was really helpful! On your link for the battery it says its rated for 1200w and I was told I would need a 50amp bms in the battery to run the 1800w kit. Have you had any issues running your battery?
@BRichSolution 10 ай бұрын
No issues with performance with the 14Ah or 20Ah battery
@RHauto 10 ай бұрын
That's good to hear 😁 Thanks for the reply bud!
@thatclappedcanam 11 ай бұрын
Hey I’m looking to do the same build this video really encouraged me to do it and helped me I was wondering what you use to charge it because the battery does not come with it
@BRichSolution 11 ай бұрын
There is an option to buy battery with or without charger
@BRichSolution 11 ай бұрын
If you didn’t order with charger this one work with the battery charge port amzn.to/476zig7
@ryancollar1 Жыл бұрын
love the video, where did you get the jumper cables?
@BRichSolution Жыл бұрын
Used a scrap piece of wire 1” long
@grahamemerick4548 11 ай бұрын
Hi I am not sure if you are checking comments, but thank you so much for the video. I have managed to get to the point where all I need to do is wire the on and off switch. I can’t quite figure out what I need to do there. Do you think you could give me some advice?
@BRichSolution 11 ай бұрын
glad I could help.... I forgot o film the the wiring on/off switch but you can see it wired at 28:57 in this video
@kingsosa7288 Жыл бұрын
The bar ends are so when u wreck the bar doesn't stab into u and never use soap to put grips on. They won't dry and slip off
@BRichSolution Жыл бұрын
The soapy water dried and grips tight
@GreySchobloher-ce1uf Жыл бұрын
I’m about to do this once I save up the money. Great tutorial. How long does the battery last?
@BRichSolution Жыл бұрын
12 miles in high longer mixed riding
@ih0nda Жыл бұрын
My son has mx125 with upgraded makita 18v power tool battery. It goes a little faster and longer playtime for him. Also looking to get a used mx650 wanted to upgrade just the battery into lithium for longer riding time as well but also keep same motor and controller. My question is 48v 20ah a good idea for it or bad? Thanks in advance if you ever or not reply. Awesome builds!
@BRichSolution Жыл бұрын
20ah battery option is a great idea the bike will run for a long time
@evananderson2918 2 ай бұрын
Do you use the stock on/off button for this build, and if I didn’t want to do the headlights/with the switch would I still need the step down transformer?
@BRichSolution 2 ай бұрын
See video at 28:57 for on/off switch wirings. Step down transformer not need if you forego headlight
@jamesobrien6855 Жыл бұрын
Thanks for making my decision easier to make. I wasn't trying to spend alot this worked out perfect for me. Just bought same bike, same vevor kit and battery with charger. Am I missing anything else that is needed? I read the description and noticed there's alot listed but I'm basically looking to start out bare minimum upgrade later. Is heat sink highly recommended? Thanks.
@BRichSolution Жыл бұрын
I’d get the hydraulic brakes and calipers for $60-70 as the stock brakes are insufficient for speed above 25 mph.
@timm8247 Жыл бұрын
Thanks again for the video! I didn’t use the 3 speed throttle and it’s a bit jumpy at initial start, can I reduce the snappy start with a better throttle or different sprocket? Thanks!
@BRichSolution Жыл бұрын
Go to 12 or 13 tooth sprocket will make it less jumpy
@timm8247 Жыл бұрын
@@BRichSolution is it a standard 13t sprocket- 4mm thickness (25h chain) 8.5 by 10mm sprocket?
@steezben319 11 ай бұрын
If you are still responding to comments on this build... if I use the stock motor sprocket and use the stock chain it will be snappy (good for wheelies, 32mph according to you) will it still be a comfortable ride when not doing wheelies? I just don't want it to be so snappy it throw's someone off the back... thank you for the help and this great tutorial.
@BRichSolution 11 ай бұрын
It will not throw the person off you’ll be good
@Avidosart1 Жыл бұрын
So glad I found this! Gonna be attempting this on the weekend. Is it best to wire a fuse in the set up or is it not necessary. Thanks for the amazing video!
@BRichSolution Жыл бұрын
Not needed as the battery has a BMS bit you can if you want extra layer of protection
@warpdriver2076 Жыл бұрын
Did you purchase the battery with a charger or did you wire the battery into the existing razor charge port?
@BRichSolution Жыл бұрын
Battery with charger and let the factory charge port hang out the back by the motor. It shows it in the video
@davidlewis3693 Жыл бұрын
Great video thanks! I have a question about your battery and motor… the battery you linked says max of 1200w output but you’re using it with an 1800w motor. Does that just make the motor run slower…?
@BRichSolution Жыл бұрын
No, the 1200w option battery has minimum of 30 amp output BMS so it can supply the 1800w motor. I used this battery it my 1800w builds
@davidlewis3693 Жыл бұрын
I don’t understand? I’ve been looking for a battery to power my 48v 2000w motor but all 48v batteries I find are rated at 1800w max… what should I be looking for?
@_Razonster Жыл бұрын
And also how did you connect the on/off switch to the side panels you didn’t show that in the video or do you just unplug the battery
@BRichSolution Жыл бұрын
See video at 28:57 for connecting on/off switch
@DaveDivesIn Жыл бұрын
Hey Brother, great video, would you have the links for the Velcro straps?
@BRichSolution Жыл бұрын
I believe they were 18” long straps here is link to variety pack for $8.99 amzn.to/3ZCOpcH
@Seth_69 Жыл бұрын
Can you do a video showing how to plug in the stock on an off switch to the E Lockport
@BRichSolution Жыл бұрын
You can see wiring in this video at 29:00 and my other video has diagrams kzfaq.info/get/bejne/qs6WhNx00snenJ8.html at 5:40
@lukez3501 Жыл бұрын
For the modification to motor does it matter what drill or do u just drill the hole a little bit deeper
@BRichSolution Жыл бұрын
Just drill the hole a little deeper so the head of the bolts are below flush so motor can mount in frame
@TooTall2Sk8 Жыл бұрын
I have a question? Is it possible to run the SX500 wheels on the MX500 or MX650 . I’m looking to see if I could run a set of the smaller ones instead of the MX stock ones? Please let me know if possible and if not what alternatives are there? Please and thank you
@BRichSolution Жыл бұрын
Yes you can put sx500 front wheel on mx500 or mx650 and vise versa
@tinyking4114 Жыл бұрын
do you mind explaining how the display shows the voltage? I get that you splice it but where does that connector hook up to?
@BRichSolution Жыл бұрын
Voltage display you can splice to any connector on the controller outputting 48V like the indicator harness or splice into charge red wire on charge port
@mykwilwin 4 ай бұрын
I did the $20 +5 kit I might do this next for more speed.
@BRichSolution 4 ай бұрын
Good idea to upgrade in steps
@dongood1386 11 ай бұрын
We have a throttle with a volt meter we aren't doing 3 speed so it's just throttle and volt meter. We have a Red, Green, and Black wire on the throttle all in one clip and then a yellow and blue wire each in heat clips. What is the coloring for the wires into the controller you used?
@BRichSolution 11 ай бұрын
Blue and yellow wires go to indicator harness on the controller. 3 throttle wires go to the throttle harness on controller
@lynngeorge1762 Жыл бұрын
@B Rich. I’m using the links you provided and when I go to eBay for the 48v lithium battery it makes you select for type of motor it will be used for, the only selection available is for the
@BRichSolution Жыл бұрын
1200w battery is sufficient 48v with 30A discharge
@lynngeorge1762 Жыл бұрын
Thanks for the quick response! If I just start with the upgraded battery first, do you recommend anything else since I have the bike apart? Like the heat shrink or anything?
@lynngeorge1762 Жыл бұрын
I finally got everything in to upgrade to the 48v lithium batteries you had linked using the stock controller and motor. Which video of yours is the best to use showing the steps to install this please? Thanks
@cooperhigginson3255 Жыл бұрын
I have had a problem with the free wheel breaking due to the high power of the bike I was wondering if you have a solution to help the free wheel to not break or you just buy a new one?
@BRichSolution Жыл бұрын
I wish I had a solution. Try new free wheel and if the tire is worn by full assembly as it might be cheaper. You could try welding the free wheel hub
@PhonyRice Жыл бұрын
Question!! Do i need the step down unit if im not using a 3 speed throttle? Also whats the benefit of getting the 3 speed throttle vs the throttle that comes with the engine
@BRichSolution Жыл бұрын
No you don’t need the step down transformer for the throttle, its only need to run the headlights and taillights as they are 12 volts. You can use the single speed throttle that comes with the motor kit but be sure the motor is in high gear all the time by using jumper wire on the 3 speed wire harness on the controller: see video at 5:16. The benefit of having a 3 speed is better control in low gear off road. Also if kids rides ride the bike you can lower the gear
@PhonyRice Жыл бұрын
@@BRichSolution hey thank you so much for the reply I appreciate the help!
@davidtreto9597 Жыл бұрын
do you need to wire the e lock to the stock on off switch or can you just bypass the old switch and only have the e lock switch?
@BRichSolution Жыл бұрын
You can bypass the stock switch
@HoeLeeFuQQ Жыл бұрын
Bro this is a good diy video thank you. Any updates how is it holding up?
@BRichSolution Жыл бұрын
I have two bikes with this setup. Both still running strong no issues
@evananderson2918 2 ай бұрын
In this video you used the 14ah version of the 48v battery and I am going to do the 20ah version for more ride time, is all of the wiring the same between those two battery’s? Thank you.
@BRichSolution 2 ай бұрын
Yes same wiring for 20Ah battery. Enjoy and good luck
@thealphateam2986 Жыл бұрын
i love this vid so much i think i might give it a shot what do you think
@BRichSolution Жыл бұрын
Sounds good and thanks for the feedback
@Tsibs98 11 күн бұрын
This I a great tutorial but I was wondering about the heatsink. Did I come with the kit? Do you need one or will it overheat? Where can I get one?
@BRichSolution 11 күн бұрын
You dont need the heat sink u less heavy rider. You buy it separately for $30 if you need it
@Tsibs98 11 күн бұрын
Oh ok thanks
@mtndrew9624 Жыл бұрын
How do you do the Elock part? I know you mentioned it at the end of the video, but you never showed us how to do it.
@BRichSolution Жыл бұрын
collect the 2 wires coming out of on/off switch on the razor to 2 wires on the elock port. If the switch turns on when it off then reverse the wires.
@JohnnyBenzekri 22 күн бұрын
I saw that he used wires to get everything to get going but i couldn't jump start the bike every time i wanted to ride it and wanted to find an on/off switch that would be compatible with the bike. Are there any recommendations?
@BRichSolution 22 күн бұрын
Wire the elock switch to factory on/off switch
@Tdot2340 Жыл бұрын
Can you use the stock charger without using the lights with the step down transformer
@BRichSolution Жыл бұрын
No
@Ed-soda 11 ай бұрын
Do you know is the original charging brick/cable is compatible with this battery if you use the existing charge port and controller connection? You mention it around 14:11 but the input and output ratings on the charge cable that comes with the battery are different than the stock charger and I don't know enough about the electronics side to know if that would still work. Thanks.
@BRichSolution 11 ай бұрын
no the old charger is 36v, you need a new charger that is 48v
@robertplayzgames8980 5 ай бұрын
For the weatherproof thing did you have anything on it or something covering it?
@BRichSolution 5 ай бұрын
I made sure the connections and controller are packaged inside the battery box
@aidanblue1005 Жыл бұрын
thank you so much
@BRichSolution Жыл бұрын
Glad I can help
@aidanblue1005 Жыл бұрын
@@BRichSolution also do you think it would work on a mx350 or is it just too small
@davewieder9634 Жыл бұрын
This is the best video on this upgrade where is the parts location list I want to purchase everything used in this tutorial. Thanks
@BRichSolution Жыл бұрын
Glad it helped
@liberty0831 11 ай бұрын
Does the brake rotor you listed in the description come with 2 or 1?
@BRichSolution 11 ай бұрын
1
@holdenfitzgerald4212 Жыл бұрын
Did the motor hall center have a red wire cut. Mine does, it’s looks like it’s on purpose but i don’t know. Thanks
@BRichSolution Жыл бұрын
It did not
@mrcappybara3372 Жыл бұрын
I was about to buy the whole kit but I had a question, what gauge is the jumper wires?
@BRichSolution Жыл бұрын
I just use some scrap 16 or 18 awg to test the system
@maderaj6354 Жыл бұрын
does this build work for a sx 500. also , can you list the 20ah version of the battery in the description as well
@TooTall2Sk8 Жыл бұрын
Yes it will work. And he did leave the link below . Click it and you can choose other options for the battery’s.
@BRichSolution Жыл бұрын
Yes it works. More room in battery box with sx500. First build was sx500 see video. kzfaq.info/get/bejne/rc-Sfa16tLLHZWw.html
@Tdot2340 Жыл бұрын
Do you think you can post where you got all the stuff because I’m trying to put together kit and it’s going well over $550
@BRichSolution Жыл бұрын
all the products used in video are in description below the video.
@Armandot6 9 ай бұрын
Isn't the rear disc brake 140mm? When you upgrade them to 160mm does the brake set accommodate for that? Thanks!
@BRichSolution 9 ай бұрын
When you upgrade to hydraulic brakes the stock 3mm thick rotors will not fit and you need 2mm thick rotors that are 160mm diameter. See parts list www.amazon.com/shop/brich/list/2A0OX01IQELT4?ref_=cm_sw_r_apin_aipsflist_aipsfbrich_HACDTVEAKMBVKX6M3P5T
@cooperhigginson3255 Жыл бұрын
My bike has worked great but recently there is like a short in my bike and I don’t know where it would be do you know any possible places where the shirt would be?
@BRichSolution Жыл бұрын
What connectors did you use? Take battery cover off twist the throttle in dark garage and you will see blue spark
@730Marcus 11 ай бұрын
Thanks! One quick question how do you charge the battery.
@BRichSolution 11 ай бұрын
Use the charger that came with the battery run the pig tail of the charger port out the back of battery box and charge it there.
@SurRazor 5 ай бұрын
I’ve been enjoying mine for a while until today , have you ever experience throttle problems ? At first it was getting stuck , but now my throttle is not responding at all 😕 Do you have any tips ?
@BRichSolution 5 ай бұрын
Did the throttle get wet? Also check the connection with controller? I had this happen on ebike and replaced the throttle and everything okay
@Sahil_Patel825 Жыл бұрын
How do you wire the on/off switch can you show how to do that? Thanks for the detailed video it really helped
@BRichSolution Жыл бұрын
With the on / off switch to the elock harness on new controller, see video at 29:04
@Sahil_Patel825 11 ай бұрын
@@BRichSolutionalso where do I get one of those jumper wires what do I search up
@Sahil_Patel825 10 ай бұрын
@@BRichSolutionalso where can I get that jumper cable in details because I do not know much about wiring
@robertplayzgames8980 5 ай бұрын
Hey man I'm gonna do this build but i do have a question, Is this build water proof because i want to make sure i don't ruin the bike when i clean it!! thanks man for the video this will help me so much the wiring couldn't do it without you.
@BRichSolution 5 ай бұрын
Yes weatherproof as I have rode in the rain no issues
@robertplayzgames8980 5 ай бұрын
@@BRichSolution Thank you!
@kudansuarez Жыл бұрын
If you use the 20ah version of the battery how far do you think it will go before it’s dead?
@BRichSolution Жыл бұрын
20-25 miles or more with full throttle. Could go further (30 miles) if not in high gear or full throttle all the time
@kudansuarez Жыл бұрын
Do you know if crf50 plastics will fit on a sx500?
@ryancollar1 Жыл бұрын
Hey just built mine and I love it! I’m running an 11 tooth sprocket with on flat ground goes around 20-25 miles per hour with a 110 pound person on it. Do you think I’m stuck in mode 2 or is it the sprocket?
@BRichSolution Жыл бұрын
Yes stuck in default mode 2, wire the 3 speed wire harness as shown video with jumper wire to mode 3 or high. You you be at 30 mph with 11T sprocket
@ryancollar1 Жыл бұрын
@@BRichSolution does this apply to the single speed throttle?
@jingostanklong1265 Жыл бұрын
How long did this build take?
@ryancollar1 Жыл бұрын
@@jingostanklong1265 in total 1 week if you count how long it took for everything to arrive, i wired it all up in less than 3 hours when it arrived
@Orvontix Жыл бұрын
would it be fine to add the upgrades to a mototec? just the performance upgrades i have the 48v pro version
@BRichSolution Жыл бұрын
Yes you can add this to mototec 48v but you may want to upgrade the batteries if mototec don’t last long
@Christian-gw3fb 7 ай бұрын
Sorry I forgot to ask. Can you keep the jumper wire permanently for the elock
@BRichSolution 7 ай бұрын
You can or just cut the harness off and butt connect the wires together
@samgriffin1763 11 ай бұрын
Is getting the 20ah battery a good idea or should I just stick with the normal one?
@BRichSolution 11 ай бұрын
If you can afford it get 20Ah
@chris2rll Ай бұрын
i’m a little confused on the 3 speed wiring, am i going to need any specific tools to make that happen? i’m new to this stuff and just want it to work overall in the end
@BRichSolution Ай бұрын
No special tools: you can permanently wire it high by connecting 2 wires and use the single speed throttle or use a 3 speed throttle and connect the wires to the 3 speed harness on the controller using butt connectors or solder and seal connectors
@chris2rll Ай бұрын
@@BRichSolution Thanks so much
@bingxautry 9 ай бұрын
Just finished my build. I have a key switch throttle and the voltage meter is always on, any fix for this? I also top out at 21MPH on the stock sprocket - could it possibly be in the lowest power mode as I don’t have a 3 speed? Thanks!
@BRichSolution 9 ай бұрын
Is the key wired to elock harness on controller
@zitera4190 Жыл бұрын
I have a question, if I do not have enough money can I just buy the motor and install that then install the other stuff later on?
@BRichSolution Жыл бұрын
Opposite. Install 48v battery with stock motor and controller. kzfaq.info/get/bejne/r91nqpOnr9i7k30.html Then upgrade to 1800w or 2000w motor later.
@4strokefrosty Жыл бұрын
Does this apply to the mx350? Nice vid bro
@BRichSolution Жыл бұрын
Mx350 and mx400 frame is smaller and motor mounts would need to modified
@77jbob 4 ай бұрын
How did the throttle hold up?I got the same one I think and yesterday I was putting it on and it came apart
@BRichSolution 4 ай бұрын
The 2 i have still good a year later
@77jbob 4 ай бұрын
Ok. Maybe I tightened the set screw to tight?
@LukeTheNukeRC Жыл бұрын
Im also building a 48v SX500 bike, but need a different on/off switch. Do you know one with a connecter that fits the 48v ESC?
@BRichSolution Жыл бұрын
The stock on/off switch on the razor you can wire to the elock port in the 1800w controller
@LukeTheNukeRC Жыл бұрын
@@BRichSolution Thank you very much!
@kratzkekyle 11 ай бұрын
How did you mount the controller? Also, if you're not using the 3 speed throttle, do you just leave the jumper cable in the 3 speed throttle?
@BRichSolution 11 ай бұрын
Screwed controller to frame Cut 3 speed wires and connect to make high speed
@kratzkekyle 11 ай бұрын
@@BRichSolution thank you, got the controller mounted to the frame. Using a single speed throttle and left the jumper on high speed. I left on the stock brakes, what do you do with the two brake connectors?
@Lux_Lifestyle11 10 ай бұрын
On my controller the battery connector was just a wire without that metal circle, to connect the battery to that can I just shrink wrap them together?
@BRichSolution 10 ай бұрын
Yes
@cheeseburber7388 3 ай бұрын
I can’t figure out how to wire the on and off switch because I’m not using the step down transformer and also what wires did you use? and you think you can make it so you don’t have to use the on and off switch and immediately turn it off by the battery
@BRichSolution 3 ай бұрын
Wire the factory on/off switch to the elock harness on controller
@cheeseburber7388 3 ай бұрын
@@BRichSolution ok thank you
@grahamemerick4548 11 ай бұрын
I I have having a great time with my upgraded bike, however the motor started to over heat after a little while. What heat sink did you use?
@BRichSolution 11 ай бұрын
motor heat sink: ebay.us/SDi2Xt
@grahamemerick4548 11 ай бұрын
Thank you
@miminguyen4674 4 күн бұрын
I bought the exact same throttle as you did twice because the first time the 2nd gear did not work and now it happened again with the new one. Did that happen with you?
@BRichSolution 3 күн бұрын
Ya only 2 gears on 2nd build
@949viggo 3 ай бұрын
I just got the same kit but my battery hasn’t came yet so I got a question. Is the stock throttle just plug and play and if not what do I have to do to make it work?
@BRichSolution 3 ай бұрын
The throttle than comes with the 2000w motor kit is plug and play. The stock razor throttle is not
@949viggo 3 ай бұрын
@@BRichSolution Thank you!
@terranceenick Жыл бұрын
Can you make a video of how you connected the batter to on and off cause I don’t know what switch to use
@BRichSolution Жыл бұрын
See video at 28:57 I simply wire the two wire going to the on/off switch to the two wires on the elock harness
@terranceenick Жыл бұрын
@@BRichSolution is it the bigger or smaller switch
@GG6502kw 13 күн бұрын
Just asking is the heat on the battery and cables needed or optional? And also the yellow box is not available on Amazon. Any substitutions for it?
@BRichSolution 13 күн бұрын
Heat gun melts the solder and waterproof seals the connection you can also use lever connectors if you don’t want use solder/seal connectors. Here is updated link to junction box amzn.to/4c4rvRI
@GG6502kw 13 күн бұрын
@@BRichSolutionthanks man! Can this thing also do wheelies?!? 🤪
@troxlen353 11 ай бұрын
can i buy some of the items and install them and then whenever i save up enough money and buy the other items? Like can i just buy the brakes now or wait till i can buy everything.
@BRichSolution 11 ай бұрын
Yes, start with the battery and connect to stock controller & motor. Ride that for a few months and then upgrade motor see this video kzfaq.info/get/bejne/obimjKR6ls7Ik2g.html
@evananderson2918 Ай бұрын
If I use the throttle with the key start, I wouldn’t need the “jumper cable” to start the system while doing the bench test correct?
@evananderson2918 Ай бұрын
Because I would simply just turn the key and the system would turn on right?
@BRichSolution Ай бұрын
No, connect the key wires to elock port on controller and no need to factory on/off switch. Make sure to wire 3 speed permanently in high so top speed is 33
@rocksolid1829 Жыл бұрын
This is the best tutorial! Unfortunately, I haven’t been able To get setup to work after trying the 3 speed throttle. It worked with the throttle that came with just but won’t with three speed. I tried to plug back in regular throttle and now it won’t work either. Any help would be greatly appreciated. Ordered everything from the video link.
@BRichSolution Жыл бұрын
Does the elock port have a switch or jumper wire? You can used just the single speed throttle and wire the 3 speed in high
@rocksolid1829 Жыл бұрын
@@BRichSolution the elock has a switch. I tried switching back to the single speed throttle but it’s not working anymore. I did originally when I tested before trying the three speed. After I couldn’t get the three speed to work, I tried going back to the single now nothing will work. Is it possible I shorted something out our ruined the controller/motor? Thanks btw! Just a dad trying to spend quality time with my boys. I have limited electric skills but wanting to learn and teach them along the way
@rocksolid1829 Жыл бұрын
I got it to work! Originally I was usi the quick connects before I committed to crimping. I decided to start over and do overthibg the video said. After putting the connectors on it worked! Thanks again man
@user-hg6gy9rf1r 9 ай бұрын
I just ordered all of this. Only thing I couldn’t see from the videos I’ve watched is a acceleration run. The video that you showed top speed seemed like it took a long time to get there.
@BRichSolution 9 ай бұрын
I went with 13T to lower the torque so I wouldn’t wheelie. If you keep 11T you will gain speed quick but top speed will be reduced to 32 mph
@user-hg6gy9rf1r 9 ай бұрын
@@BRichSolution yeah I ended up holding off on the 13t. I also have a razor pocket mod (moped) I got them both free. And I’m gonna build it next if this one goes good
@jjjjjedii_cars 2 күн бұрын
so for the on off switch is it just a plug and play or do u have to custom wire it?
@BRichSolution 2 күн бұрын
See video at 28:57 for wiring elock harness to factory on/off switch
@grahamemerick4548 11 ай бұрын
Are the wires that go into the e lock the 2 large wires that come out of the on off switch?
@BRichSolution 11 ай бұрын
Yes
@bg123_____12 11 ай бұрын
Thanks for the tutorial. I followed everything you did and same parts but in high mode I’m getting 23 mph. Do you know a fix?
@BRichSolution 11 ай бұрын
3 speed is not wired properly. Its in low. Need to wire 3 speed in high
@BRichSolution 11 ай бұрын
See video at 5:16 for wiring 3 speed in high
@570kid8 11 ай бұрын
Same with me I’ve wired it to speed 3 and I’m still only going 24-25
@miminguyen4674 14 күн бұрын
How did you connect the e lock to the on/off switch? Because the on/off switch has 2 connectors. Also how did you wire the charging port?
@BRichSolution 14 күн бұрын
See video at 28:57 you can see elock connected to factory on/off switch
@miminguyen4674 14 күн бұрын
How did you wire the charging port?
@cooperhigginson3255 Жыл бұрын
Wait so should I just return the battery and motor I got or should I try and make it fit?
@BRichSolution Жыл бұрын
Depends on your skills. To fit the 4” diameter motor in mx400 requires welding on new mount location
@gregblau8082 Жыл бұрын
I'm looking at one of these for my son that needs a battery. If he's into it I'll probably do the whole upgrade, but don't want to invest that much yet. Will the upgraded battery work on an otherwise stock bike?
@BRichSolution Жыл бұрын
yes, you can buy 48V and connect to stock controller & motor. You will have performance gains. Then later on upgrade the motor & controller. See video for 48V with stock motor and controller kzfaq.info/get/bejne/obimjKR6ls7Ik2g.html
@gregblau8082 Жыл бұрын
Just watched it. Thanks
@robisonrogers3678 Жыл бұрын
Just as I was wrapping up my build I'm now seeing issues with the throttle working intermittently and now almost not at all. Initially it worked great. Issues happened to coincide with swapping out the sprocket on the upgraded motor with the sprocket on the stock motor. (Long story short I was using a stock chain and the upgraded motor sprockets are a bit wider which was causing a lot of noise when riding). Any thoughts on what it could be or troubleshooting steps? Followed your video pretty closely for the motor, battery, controller and lights on a SX 500 frame. Thanks for your videos BTW very helpful.
@BRichSolution Жыл бұрын
Is the chain slipping with the new sprocket?
@steezben319 11 ай бұрын
What is the heat sink used for? Do i need it and is it safe to ride without one?
@BRichSolution 11 ай бұрын
I don’t think you need it unless your heavy rider or excessive off road
Jeremy Walter
Рет қаралды 255 М.
DIY Zoonomaly Zookeepers Kinder Joy | PaperCraft Ideas #shorts #papercraft #toys #art #diy #unboxing
learning song
Рет қаралды 8 МЛН
Voltron Watts
Рет қаралды 22 М.
Electric OHV
Рет қаралды 12 М.
Pat Outdoors
Рет қаралды 49 М.
MarleyJax Garage
Рет қаралды 102 М.
RusMovies
Рет қаралды 543 М.
MotoTaper
Рет қаралды 977 М.