3rd Gen 4Runner Lift Install - Tundra TRD Coils and 906 Springs

Рет қаралды 416,105

10 жыл бұрын

Join the Channel! / @speedysgarage
Wheels: amzn.to/3jiCH4g
Center Caps: amzn.to/3sXcwU3
Tundra TRD Coil Springs Used: amzn.to/2OTn5EZ amzn.to/2uIANDG
Isolators: amzn.to/31QZYA5
5100 Front Shocks: amzn.to/3kCwfJ8
5100 Rear Shocks: amzn.to/3L8JsUX
OME 906 Rear Springs: amzn.to/31RsFgc
Stuff I use:
Race Ramps: amzn.to/2Sicrdt
Race Ramp Low Profile Extension: amzn.to/2MhlDLa
Tire Rack: amzn.to/38X0foa
Cordless Ratchet: amzn.to/3uxBwkV
Cordless 1/2" Impact: amzn.to/2MlxMyL
Cordless 3/8" Impact: amzn.to/2sPLm6K
Ratchet Set: amzn.to/2QbKsJK
Wrench Set: amzn.to/374jt9R
Impact Socket Set: amzn.to/3o06wYh
Impact Socket Set: amzn.to/3xSpiW5
Lug Nut Set: amzn.to/3o1maCu
www.speedysgarage.net
Today at Speedy's Garage see how to install a lift kit on a 3rd gen 4Runner using Tundra TRD Coils in the front with Bilstein 5100 shocks and OME 906 coils in the rear with 5100 shocks. Before and after measurements shown. Ride is better than stock in that it is not only smoother and more compliant, but the vehicle has a meaner look to boot 😎

Пікірлер: 499

@jevoistout5786 6 жыл бұрын

Finally!! A video that skips the b.s talk and music and shows you step by step instructions and detail. Great video

@SpeedysGarage 6 жыл бұрын

LOL, my channel has a bit of both to try to have something for everybody. I plan to keep the mix with some "chat" and a lot of "how to".

@JoseMartinez-jw2dy 5 жыл бұрын

People don't ruin your ride,do you see that axle and ball joints angle ,really bad ,I used to do this to my trucks, not anymore more it changes how factory ride is supposed to be,stay away from leveling kits

@rediranch 10 жыл бұрын

Thanks for taking the time to video this, it is appreciated. I've done lifts on vehicles before but it's been a while, this was a nice refresher before I got into it.

@LifestrongCo. 4 жыл бұрын

This is one of the best install vids on youtube. Super detailed review, so detailed I'm doing my rig while watching. Great Job !

@TheGwolk 10 жыл бұрын

absolutely amazing video. You explained WHY you did everything, instead of just showing what to do, which made it much easier to understand. As of right now, you're on of my favorite guys on youtube. diffidently subscribing.

@christopheradams7309 4 жыл бұрын

Couldn't of said it better

@morphic31 10 жыл бұрын

Excellent thorough video. I like that you give reminders on washer orientation, reattaching the e-brake cable and brake line on the pumpkin (even the spare!) Much appreciated!

@preferablyoutside 5 жыл бұрын

thanks so much for making this video! still relevant in 2019. I had the bottle jack pop out twice on me while under load, but with the proper blocks in place and eventually the impact-driver extension, it really was not very violent... just more of a surprise. also helped to generally avoid putting any body parts in the line of fire. anyway, this is a fantastic walk through. I owe you a beer, sir.

@globalmobile017 7 жыл бұрын

Thanks to this video I completed the lift and had no issues. Using the bottle jack upside down was very easy. Just make sure it's in good. Most of my bolts needed the sawzall, but after that it was easy.

@robertmccabe7328 4 жыл бұрын

Awesome! viewed this before i replaced all shocks and springs on my 2002 4runner. Getting to rear shock/top nut was a challenge but all in 2 hours for back spring and shocks. 3 hours for front

@jvogler_art4708 2 жыл бұрын

This seems like the best lift for my 4runner. Cheapest too. Exactly what i wanted. Highway comfort with slightly better clearance for offroading.

@triedandtrue1820 4 жыл бұрын

Had same lift for 10 yrs, rides same as day of install. It's a heavy duty upgrade, carried 4 guys and all gear with camping supplies, truck sits level. 1999 4runner SR5

@hongkeejoseph Жыл бұрын

Still recommend it? Tundra fronts feel pretty good?

@SangTran-zn7lq 3 жыл бұрын

Your video helped accelerated my install. Appreciate the details and effort you into this video.

@stevelongacre5829 4 жыл бұрын

Thank you for a straight forward easy to understand video on these installs. Well done.

@sethdunn96 5 жыл бұрын

Hey man, thanks for the video and detailed how-to of it. I just finished the lift on my 4Runner going by this video. Also got the parts from Wheelers. Appreciate you taking the time to put this video together

@eddiereyna2308 5 жыл бұрын

Seth Dunn have a link to the parts??

@Davis2you 4 жыл бұрын

This is the ONLY good video in 3rd gen lift. Thank you

@RichardMularski 6 жыл бұрын

Thank You Speedy Like Many others here that have watched, made my install go seamless, thanks again

@firstgenjon 3 ай бұрын

Thnx for sharing. Doing a 2” lift on my first gen sequoia this week. This was quite helpful.

@enduromite 9 жыл бұрын

Thanks for the bottle jack recommendation to remove/install front shocks easier. I'm sure you saved me a bunch of frustration!

@enmanuelcash6574 6 жыл бұрын

Speedy you are a admiration! I have all exact parts on there way and we are now on mid Oct 2017. Still inspiring!

@scubbarookie 4 жыл бұрын

Thank you! This video was very educational and encouraging. Great work! Love those wheels and suspension upgrades.

@yeahright2449 5 жыл бұрын

Thank you for making this video! I'll be using it to do my lift this week

@DocGeoz 10 жыл бұрын

Super clean car! I'm in the market for a 3rd gen T4R and I've bookmarked your site and vids!! Thanks for taking the time to make high quality, and easy to follow DIY's.

@karltaylor1740 3 жыл бұрын

This was the best install video. Ive nvr said this before about any other youtube video but this was on par with a chrisfix video no doubt

@juansterthemonster21 7 жыл бұрын

Super helpful. I have an FJ Cruiser and plan to put on some Bilstein 5100's. I know it's not the same car but totally good to know the basics on how to assemble these bad boys.

@WallDiver7 2 жыл бұрын

Very nice instructional video... Thank you! A couple of notes: The top stem sockets, at least on mine, were a 5mm allen wrench instead of the 3/16" as you mentioned. The top bushings WILL allow shock-stem rub against the chassis mounting hole because Billstein was TOO cheap to provide the correct bushings. The installer can either buy a very short nylon bushing to slip over the shock stem to ride between these Billstein bushings, or re-use the old bushings from the old shock.

@getupgonow3231 9 жыл бұрын

Excellent! Your tips and explanations are well thought out! Your video shots give us a front row seat on "how to" do it! Plenty of light to see! Your attention to detail in your remarks about shock model numbers etc. gives you an A+ ! The advice on safety is something I will utilize and take heed! Nice, by far one of the best top videos! I have been working on cars for 50 years, video production for 25 years and your combination of the two is superior! Congratulations! I would like to see a video on a Gen 5 Toyota 4Runner as this is my next project installing a 3" inch OME LIFT! I will take your advice and concepts and apply it to my project! I subscribed to your channel, something I rarely do! Very professional presentation! Kudos!!

@stevejette2329 6 жыл бұрын

Get Up & Go Now - I totally agree. The VIDEO is well done. Sound, camera, light, sound ... 94 4Runner now

@ZacCostilla 4 жыл бұрын

This is a great step-by-step on how to do this. I mostly want a better ride quality and maybe 1” max of lift, so I think I’ll do this but compress the front spring more than you did. Not sure how I’m going to do the back, but might use the same springs you did and accept the 2” of lift.

@ohtwo23 7 жыл бұрын

Doing my truck now. Ordered my 5100's from Tire Rack. Bushings with them are the correct ones.

@RicardoGomezToro 9 жыл бұрын

I performed the same installation on m 2002. I am happy with the results. Rides better than stock. Brakes are next.

@dylrichardson 9 жыл бұрын

Great informative video. I used this as a guide for replacing my shocks on my 2000 4runner.

@chadduckworth6357 3 жыл бұрын

Don't even need to see another video. Subscribed after this one alone. Great explanations!!

@chadjacobsen1 8 жыл бұрын

I have to say, this was an awesome job on the install and very informative! Thank you speedy! i will be subscribing to your channel just from this video. I am installing a rear lift in my 5th gen 4runner, (2015) next weekend after my H.A.M. hunt. New SAW coil springs and 5100 series shocks, (already installed new adjustable front coils from Toytech in the front). i just got a new Gopro camera for Xmas so i might do a small video on how to do it on a 5th gen after watching your video. again, really great job and hope your 4 runner is still running strong. Gotta love the 4 runners!!!

@4bob432 5 жыл бұрын

I appreciate the conciseness of the video! Thanks man! You've got a new sub!

@greenflintriver 8 жыл бұрын

I took your advice did the same install Love It. Great video Great Package Perfect Ride. Thanks Speedy

@kevinpuckett4145 3 жыл бұрын

Just did this to my 1999 limited and it rides like a dream.

@dustywizard1104 4 жыл бұрын

you always post the most detailed and comprehensive videos, thank you. and sweeeeet rig

@brianabston4280 8 жыл бұрын

Awesome video and site. I am going to start shopping around today to do this on my 98 4Runner

@Da_Goon_Rider 3 жыл бұрын

Thank you so much for this I got a 3rd gen to and needed some advice because I want to do a lift. Thank you so much🙏🙏🙏🙏🙏 you should do more 4Runner mod videos.

@SingleSubScrub 4 жыл бұрын

Great video. FYI another way to remove the rear shocks easily is by removing the bottom bolt, and bending them until they snap at the top. Took me 2-5 minutes to do each.

@jp.purdom 9 жыл бұрын

Great vid. And i overheard Two Door Cinema Club in the background and got so stoked

@hugos.5059 7 жыл бұрын

You make it seem so easy... I have a 2000 4Runner.. I've been wanting to do this as well... perhaps one day.. good video.!!!

@dragonfly6243 4 жыл бұрын

Dude you explain things really well. Your an awesome teacher.

@KilllBox 3 жыл бұрын

Thank you. This is the exact video I needed. I truly appreciate the meticulous attention to detail.

@SpeedysGarage 3 жыл бұрын

Glad it was helpful!

@abrahammcdermett3624 3 жыл бұрын

Awesome! Gave me the inspiration to do the install on my 4Runner. Thank you!

@nickcarverphoto 7 жыл бұрын

Geeze man this was so helpful. Thank you for making such a great video.

@SnoopyGSX 4 жыл бұрын

very nice video sir! Because it's so thorough, hands on, and informative.

@mikecampbell7361 7 жыл бұрын

Great video. what I've been looking for, appreciate all the detail.

@taatibarao3764 4 жыл бұрын

I love your tutorial, well explained especially love your improvised techniques, Got another subscriber...cheers

@theregularguy5409 2 жыл бұрын

I can’t believe i used to watch this video and freaking out if I can Do it myself. Last week i went and converted my automatic hubs to manual on this 4runner😂

@TheSaturnV 5 жыл бұрын

22:00 For anyone else installing coils up front, while you have them compressed and before securing the top mount, you have to get the alignment correct between the top 3 nuts and the end of the bottom of the coil spring. The bottom coil spring end must be facing the outside and point down the long axis of the vehicle. Passenger spring end points directly to the rear, driver side to the front. This will keep the spring from being too close to the upper ball joint mount. (Toyota FSM) Great video.

@Lopex-MTB 6 жыл бұрын

Awesome Vid! I will be doing this next week when my lift arrives! Nice Toy

@taconobaka1688 8 жыл бұрын

We just got a 3rd Gen 4runner. With our 1st Gen Tacoma, we now have a matched set. =D You did almost exactly what I plan to do with ours. I want to go with the same tire size, but I want to go up about 2.5" instead. I'm probably going to use the OME 881 springs off my Tacoma over a set of 5100s. I'll be going up to 883s on the Taco and replacing the OME Nitrochargers with a set of 5100s. For the back of the 4r, I'm going to try to go with a set of 5125s. Just put a set of those on the back of the Taco and they ride much better than the old OME Nitrochargers.

@tx4runner459 6 жыл бұрын

I was genuinely surprised you don’t have to take off the sway bar end off, or the upper ball joints. I’ve done leveling kits and lifts on GM, Ford and Dodges and always had to do that to them.

@Bugricua 7 жыл бұрын

Great video, excellent detailed explanation. Thanks for the product info.

@stephenlindborg5671 9 жыл бұрын

Thanks for posting this awesome vid. It was very helpful when I did this lift on my wife's 01. However I thought I'd give everyone a heads up with the rear shocks. If you order the bilstein part number from anywhere but wheelers off-road you will NOT be able to install them on your 4Runner due to the fact that the bushings that attach to the rear axle are the wrong size. Wheelers off-road takes the 5100 shock and presses different bushings in to accommodate the 4Runner. The only reason i know this is because I found a killer deal on the 5100's from a different site and was bummed out when I thought I ordered the wrong shocks. I had the idea to give the folks at wheeler a call and they explained that I did actually have the right parts but they simply put in different bushings in them. They had the proper bushings in stock and shipped them to me. Now it's all good! Just order the rears from wheelers, guys! Thanks speedy for this tutorial. It was well done as are all your vids. Keep me comin!

@williamjerry 7 жыл бұрын

I did the same as you did and end up have local shop to press out the busing and replace with a correct one for 4runner.

@seandalejackson2525 5 жыл бұрын

Will all that fit on a 1997 2wd 4runner?!?!

@skydrive75 4 жыл бұрын

@@williamjerry & @stephen what is the part number for this bushing??

@Asian_Connection 3 жыл бұрын

I like all your safety protocols!

@batbawls 8 жыл бұрын

Dude that is a sharp 3rd gen.

@ZedZerps 5 жыл бұрын

gen3 will never die

@jake27schannel 5 жыл бұрын

@@ZedZerps best looking gen

@JmanK77 10 жыл бұрын

Looks like a tight fit in there! Very nice looking truck.

@luisamoa2500 5 жыл бұрын

I don't even own a car but I LOVE your channel anyway. OCD to the max:) that's a rust free truck btw

@fernando13e 8 жыл бұрын

Hi man, great job on swapping out those suspension parts, but a good idea to loosen or lube rubber parts would be using some silicone spray on those parts, they get off soo much easier, also about the spring compressor.. You always wanna use it while having the strut mounted securely on a vise, if the compressor slips by accident it can kill you or do some serious injuries and never touch the springs while compressed with your hands!. Great work man!.

@scorpionsunday9483 5 жыл бұрын

I like the way you work safe, cheers

@briandavis55 6 жыл бұрын

I wish my 3rd gen had no rust like this. added about 5 hours of pain to doing my lift.

@drunkenmunky2131 4 жыл бұрын

Wassup brotha just got my ome front springs, is there a side preference on them they look exactly the same 🤔

@coreys121 3 жыл бұрын

@@drunkenmunky2131 what does ome stand for?

@bchriscoe3984 3 жыл бұрын

@@coreys121 old man emu

@johnpavon799 6 жыл бұрын

Great Video! Thanks for showing it!

@nolancampbell6139 2 жыл бұрын

Excellent video, well organized and helpful. Thank you!

@SpeedysGarage 2 жыл бұрын

Glad you enjoyed it!

@juanjay5958 4 жыл бұрын

Wow! Those wheels look beautiful! I have a 97 limited and I'd love to find some wheels like this but I like the stock height I don't Wana get no lift kit

@pjc4425 4 жыл бұрын

Great video! , wish I came across it 6 years ago. In that time frame I added 1” spacer to front stock spring & upgraded rear springs to moog eliminating 96 sag with 1.5” spacer & upgraded shocks. Combo provided comfy ride, looked good many compliments received In the Last year I’ve noticed rear sag taking place , nothing major but sits slightly lower then front & it bugs me. Adding 2906 springs minus rear spacers might be the fix UPDATE: Put measuring tape on my 96 limited setup finding odd results. Front 22” & Rear 22.5. 22” up front is very puzzling to me seeing I only added 1” spacer. Maybe new struts had higher ring then stocks , I’m really not freaking sure seeing install took place @ night low light , I was just throwing it together. Anyway , mid grade off brand struts gave me extra 1.5” on top of 1” spacer = 2.5” front lift. Rear spacer upgrade from 1.5 to 2” should provide results I seek. Or 809 coil with 1” spacer with unknown outcome 3” - 3.5...

@michaelwood4158 4 жыл бұрын

Great vid for sure. Glad you took the time to make a detailed video about this. Kudos! Will those rear Tundra shocks work with 891 OME springs? And with front 883 OME?

@Z-nl4ht 3 ай бұрын

Love your content would enjoy seeing more toyota stuff nice work. I'm doing a valve cover and 3" susp lift on my 02 right now... I'm wishing it had the engine bay your did 😄

@vbrtrmn 7 жыл бұрын

Great video, thanks for making it!

@edgarrangel9464 5 жыл бұрын

Hay man your video inspired me . Great job

@donedoda791 6 жыл бұрын

good as new! its has to fit, before u can in stall great stuff mate 👍

@channelderek9005 7 жыл бұрын

Well it's been one year since I perform this lift thanks to your video and everything is going great not one problem .. The only small issue I have is my front passenger is a half an inch higher than the driver side is that normal or will the coil eventually settle down

@Bimmerrx7 10 жыл бұрын

Thanks for this very detailed video.

@mayk3lll 6 жыл бұрын

Loosening the lower A arm bolt allow it to move freely instead of hanging up like it does, you can also loosen upper if you wanted to also. Allows for a much easier install

@grossmeister1181 2 жыл бұрын

That would also remove the pre-tension on the rubber mounts, wouldn't it?

@zacharyhuston1269 10 жыл бұрын

Great work. Thank you for sharing this video

@jonathanhoye1017 9 жыл бұрын

Great video man. I will definitely be using this when I do my lift. Also did you do a pan hard drop later on or no? Or do you think it isn't needed with a 2" lift?

@idinaxuie786 9 жыл бұрын

Nice truck good job, very clear explanation thanks a lot

@freeindeedfishing6706 7 жыл бұрын

Video has been super helpful in setting up my 4runner, thanks! Question though, is the coil spring isolator needed? How much wider is it? I have talked to a few friends that have done this lift and say they don't think they remember using one.

@edwardm6276 9 жыл бұрын

Thanks for the video, fantastic!

@jdmoore9618 Жыл бұрын

This vid was great. Thanks

@michaelj.kastner5165 8 жыл бұрын

The candy break is the best!!

@andreypetrash3808 9 жыл бұрын

Great video. Very helpful. Thank you

@anthonybaiocchi3028 4 жыл бұрын

Old Man Emu sell a rubber bung that allows you to use a whole saw above the rear shocks and drill a hole to get to the shock top bolts.

@heatmyzer9 3 жыл бұрын

Did not know they had this as an option ...THE most frustrating part of the job was the top nuts on the rear shocks. Still having nightmares....12 months later.

@MrToyotaExo88 7 жыл бұрын

Thanks for the detailed video speedy however your website seems to be down. I'm interested in retrieving part numbers for the TRD springs

@Texasbroski512 3 жыл бұрын

You seem super knowledgeable on the 3rd gen and know how not to get ripped off with lift kits. What would you recommend for a nice riding 3" lift.

@odiliotorres3804 3 жыл бұрын

Love your rig and videos. Thank you for being so detailed. I have the exact same set up. Did you ever have to adjust the panhard bar and sway bar links?

@SpeedysGarage 3 жыл бұрын

Did not have to do anything with the PH bar.

@FreshYoungDude 7 жыл бұрын

I love your thorough install vids. Thank you. What sliders/side steps are those? I would love to get the same ones.

@SpeedysGarage 7 жыл бұрын

I got those 15 years ago and they were just a knock off brand I had blasted and powder coated a the custom titanium color. They aren't available any longer. A set of sliders may work well for you these days. The factory Toyota sport bars aren't available any longer either.

@jasonpeaslee8671 9 жыл бұрын

This is exactly what i'm planning on doing to my 4runner (TRD/906/5100s). So you didn't find it necessary to put in an adjustable panhard bar, extended brake lines, parking brake bracket, or diff drop? Seems like everyone always says you need these, but people are often doing 3"+ of lift. Thanks for the video. This is definitely giving me some confidence in tackling this myself.

@Zevach97 3 жыл бұрын

I need this set up!!!

@newfwheels2965 8 жыл бұрын

to push the assembly down, i used a ratchet strap to haul down the top a-arm down.

@SpeedysGarage 8 жыл бұрын

Excellent suggestion.

@maxnikolaenko4308 4 жыл бұрын

Very nice and informative video!

@ns671fr 5 жыл бұрын

The bottom of the coil where it meets the spring perch needs to be facing out on both sides actually

@california199_7 5 жыл бұрын

Very helpful video, thanks

@InnovativeShooter Ай бұрын

Very nicely done presentation. Toyota parts people want to know what Tundra model this front coil spring you are referring to will be coming from. like..2000-2006 extra cab, 4 door, 4x4, or what type of engine....I appreciate your time Thanks

@Jim2205 9 жыл бұрын

Nice Video! Really good info!

@NicoleMarie120992 9 жыл бұрын

great video, did the CVs and everything hold up well?

@captnmorgan9944 4 жыл бұрын

Awesome video inspired me to attempt a lift!... quick question and probably a dumb one but did you just buy two of the same front springs? Or are they two different part numbers? Thanks! Hope to have an answer

@270wsm140gr 8 жыл бұрын

cool vid man .. do u have any add weight in fronts like steal bumper,winch does the 5100 shocks handle heavy loads good thanks for sharing

@bhdproduction2007 4 жыл бұрын

I would like to add on to this video. I just got done with the driver side and i would like to say IF you are using the bottle jack. Please place the jack behind the nut on the top arm. If you do not, the jack will have nothing to hit or lean against with all that pressure to hold it down and will pop out.

@donedoda791 6 жыл бұрын

damn they should sponsor u for all the shocks u done sold by making this video ☺