I'm definitely going to be using the gasket upgrade!
@JaeyouPark3 жыл бұрын
Loved the intro of your recent voice65 video! Thanks for stopping by :)
@case31773 жыл бұрын
i wonder if the gasket upgrade will work on other budget and midrange gasket mount boards like the kbd67lite
@XDTheLaughingManXD3 жыл бұрын
Your intros are top tier Hamaji Neo
@arc11honist3 жыл бұрын
does it still bend the pcb?
@XDTheLaughingManXD2 жыл бұрын
@@arc11honist , tbh, this pcb bends itself if you're using polycarb plate. ever so slightly, but not enough to notice.
@sviz3 жыл бұрын
This makes me wanna pick one up! Loved the adding gaskets, board sounds great
@lilrowbear3 жыл бұрын
Still a little muted to me, but you can’t really ask for much better at $170.
@JaeyouPark3 жыл бұрын
The original bottom gaskets was compressed below the alu lip around them haha so wasn't doing anything! I gotta say, the knob feels 12/10 premium :)
@user-qn1zj5bs5p2 жыл бұрын
@@lilrowbear mute is better than pingy and hollowness , dont too picky nothing is perfect
2 жыл бұрын
@@lilrowbear which is better with a knob my lk67 sounds better
@little_fluffy_clouds2 жыл бұрын
Biggest upgrades you can make are: - Switch the default GOAT stabs for some decent aftermarket ones, like lubed Durock v2s - Don't use any of the Glorious plates, buy and install the aftermarket FR4 plate by AVX works. It fits the PCB perfectly and is compatible with any brand of stabs. It looks, feels and sounds great. - Apply the gasket upgrade as shown in this video, you may use the extra gasket strips which comes with the keyboard - Install a thin layer of PE foam between the PCB and the plate, and optionally remove the stock plate foam that came with the board After that, using decent lubed switches and thick keycaps will provide you with a pleasant typing sound and experience.
@gregory_p3 жыл бұрын
Aaaah So clean! Fantastic build once again Jaeyou😄
@JaeyouPark3 жыл бұрын
Haha I can’t take too much credit as I am only modding a prebuilt in this one. Thank you though Greg!
@MrSharkswith3 жыл бұрын
Great looking board, and the sounds are fantastic! I got mine with the brass plate, and so far I love it. The only complaints I have are that the stabs, even when taken care of a bit, still aren't great, and that the cable that plugs into the PCB in the bottom doesn't line up very well when you're trying to put the board back together so it gets pinched if you aren't careful.
@Twk199111 ай бұрын
just swap it out for some durocks and you are good to go
@Dirchew3 жыл бұрын
This is so helpful, thank you so much for uploading! Subbed:)
@JaeyouPark3 жыл бұрын
Thanks for subbing! I am so glad I could help :)
@faye84003 жыл бұрын
I was so happy that I also got a PC plate when I saw that you used one :D gonna get to modding my GMMK Pro soon aswell :) great video!
@Calibeamer73 жыл бұрын
Just wanted to give you a shout out. Your video was such a blessing and help when building my gmmk pro. Your mods has made this whole process worthwhile. Looking forward to more content!
@AnzelLmao3 жыл бұрын
Good stuff, man! Can't wait to hear your first voice over video too!
@sviz3 жыл бұрын
^
@JaeyouPark3 жыл бұрын
At this rate it might have to be Q4 haha, realllllly trying to set up a proper set up before I dive in to voiceovers and streams! Thanks for the support as always though :)
@AnzelLmao3 жыл бұрын
@@JaeyouPark ay you got it bro! But i totally get where you're coming from haha, I wish I researched more about EQ before doing voiceovers, my first few were rough lmao
@JaeyouPark3 жыл бұрын
@@AnzelLmao I might have to bug you for some tips when the time comes ;) if you’re on discord, would love for you to join the community! Lots of good questions being asked, and your knowledge would be an amazing resource.
@AnzelLmao3 жыл бұрын
@@JaeyouPark count me in!!! Although I'll admit I'm no expert on audio, I just have knowledgeable buddies that help out and too many videography channels I'm subbed to LOL
@marginalmeaning3 жыл бұрын
Wow! Definitely made the switches sound much deeper after those mods. I cancelled my reservation after hearing about the ineffective gaskets and how the board kind of nulls a lot of switch sound. Might have to reconsider after hearing your mods.
@ThatDudeDeven2 жыл бұрын
Oh man I got mine a few days ago and the first thing I did was take it apart about put some lubed Gat black ink v2 stabs in there - but the first thing I noticed was how good the pads still were. I had I only seen videos about how gnarly they are when you open the board up - now they include a big bag of gaskets also. And a big bag of screws. Little off topic, but I didnt strip any screws with a size 0/00 PH. PH1 seemed a little big contrary to everyone's suggestions. It may just be ifixit in particular though.
@savsheik3 жыл бұрын
The video I’ve been lookin for for a long time! Ty
@JaeyouPark3 жыл бұрын
haha thanks for watching!
@DaveOrtiz3 жыл бұрын
Liked and subscribed. I plan to do these upgrades (sticking to Aura Keycaps and Gat Black v2s as my only variation) as soon as my GMMK Pro. That you for this video. I will have it on as I make this my first build.
@JaeyouPark3 жыл бұрын
thank you for your support! Hope your build goes well :)
@timfederwitz3 жыл бұрын
I just reserved my GMMK Pro and the PC Plate isn't in stock ATM, but I will be doing EXACTLY all of these mods as well. Great to hear the difference and know that my plan will provide my desired result!! Keep making great vidz. I am now a subscriber.
@JaeyouPark3 жыл бұрын
Glad I can help Tim! Hope your build goes well :)
@timfederwitz3 жыл бұрын
@@JaeyouPark Glorious only just got the stock in on my reservation, so I should have the board in about a week. Can't wait to get to this stuff. BTW, I had to wait for the PC plate to be in stock, but I was able to get that weeks ago and have it ready for when the GMMK Pro is delivered.
@timfederwitz3 жыл бұрын
@@JaeyouPark It took a little longer than a week to arrive, but I now have it and applied the mods. A couple things: The version I was sent actually already has pads under the stock stabs. Also, the stabs were *heavily* lubed! To the point that the spacebar wouldn't work properly. I had to take them off anyway to clean them and relube them, and that's when I noticed the pads under the stabs as stock now. Also, I purchased new PCB and case foam from StupidFish (stupidfish.design/products/gmmk-pro-case-and-plate-foam) in the 3mm size (the case foam is 2mm and has cutouts for the hotswap sockets). I feel like this foam is an additional upgrade from the stock. Finally, I am using the GMK Godspeed Apollo keycaps set and loving the build. Thanks again for posting these mods!
@chubbs62313 жыл бұрын
Great vid! Gonna come back to this when my board comes in!
@talonclark12363 жыл бұрын
I didn't add any screws back in other than the diffuser screws and it gave a keyboard a nice bounce with the poly plate and no pcb or case foam. Worth a try if you dont mind the tedious amount of work it is to take this dang board apart. Great video as always though! That keycap set goes so nice with this board.
@JaeyouPark3 жыл бұрын
That would be a good way as well! Might have to open this baby back up some day...
@UpgradingAsUsual3 жыл бұрын
From what I have experienced, the typing experience overall is wholly improved after changing from the PC plate to the Aluminium plate with the gasket mod. This is because the PC plate has issues with bowing and the consistency around the board is way off all over the place. Sure it does sound better, but only in the middle. The outer keys sound much higher pitched than the middle and it ruins the entire experience. Of course, this is all corrected with the aluminium plate. This should also apply to the brass plate, too. I will however, try to sand down the stab holes on the PC plate to give them space to move around which might help. Stock PC plate is a huge no no for me at the moment. I am going to attempt a new type of gasket mod which I will update you here in the near future. I have applied a similar mod in another type of enclosure (nothing to do with keyboards and on a much larger scale) in the past with huge success. If I could apply it on a smaller scale, the result should be the same. If the mod proves to be successful, I will update you here. Back off, man. I'm a scientist.
@ronakbarman35802 жыл бұрын
So, did it work?
@maelvomen7 ай бұрын
I finished building mine today and added tape mod and I can't believe how big of a difference it made
@bestfemale.3 жыл бұрын
This video was so good to watch since I’m about to build a GMMK pro and use same plate. Awesome video thanks for breaking it down well
@biohazardmonkey123 жыл бұрын
THANK YOU SO SO SO SOOOOO MUCH! THIS REALLY HELPED A LOT ESPECIALLY WITH MY STAB PROBS! Ordered durock v2’s after this video
@JaeyouPark3 жыл бұрын
Glad I can help! thanks for watching :)
@ThatDudeDeven2 жыл бұрын
Man, I got the gateron black ink v2 stabs and durock v2 stabs at the same time. Put the lubed durocks on for a while, then changed over to the black ink v2 stabs - I really like the black inks tbh. Idk what it is, but the sound is a bit more thocky. Not a lot more, but it's there. Balanced the wires on each and the black inks barely needed any balancing Co pared to the durocks also.
@Beinhard42 Жыл бұрын
nice video! :) What kind of dampeners did you use under your stabilizers?
@StachelyPigglyBottom3 жыл бұрын
Not to be picky, but for the before and after side by side, is the mic closer on the before shots? If so wouldn't that be an unfair comparison? Either way thanks for the video. Will likely reference this for future upgrades. If you had to pick one or two of these mods which do you think were the most impactful?
@Flybeck3 жыл бұрын
Great job! I tried creating a different type of gasket with silicone! Mods do this board justice.
@dontrom15882 жыл бұрын
I love your videos, so peaceful and incredible!
@DerisHopePilipinas3 жыл бұрын
the usual haters of this board aren't in the comments yet I see. expecting to see them soon as they go around every gmmk pro video like a mob of villagers out for a witch hunt. btw great build! Hope you can test GHP switches or alpacas
@casualcarmelogaming204 ай бұрын
Thank god you didn’t put painters tape on the PCB, I just replaced my stabilizers and put in some sea salt silent switches and it sounds amazing just after those two changes
@Keybored3 жыл бұрын
Great tutorial and advice! I'm thinking of shaving off the plate screw tabs to see if that helps to improve the gmmk feel. Let's hope it works lol
@JaeyouPark3 жыл бұрын
Haha please let me know how it goes! Maybe I will open this up again to do your tab removal mod...
@justplainlawr3 жыл бұрын
what if you replace the bottom case screws with slightly longer ones so that when you screw it together, the plate and PCB doesn't press as hard against the gasket?
@Keybored3 жыл бұрын
@@justplainlawr I think ultimately, I might end up filing down the lower case to increase the space for a thicker gasket to fit. I feel like the tolerance is too tight and it's squeezing the poor and already super thin gasket way too tight... kind of defeats the gasket mount.
@justplainlawr3 жыл бұрын
@@Keybored that’s a good idea! Looking forward to your mod video, I used your foam tape mod to help with my GMMK.
@justplainlawr3 жыл бұрын
@@Keybored oooh interesting! Looking forward to your mod video when it drops!
@PandaXpress173 жыл бұрын
I love the PC plate, but man it warps the PCB so bad. Great video!
@TrynaBeCray3 жыл бұрын
7:30- 7:45 The Polycarbonate plate looks like it's causing the PCB to bow a little. For those considering the Polycarbonate plate, alot users including myself have found the PC plate causes the PCB to bow some more than others, but it might vary from batch to batch, should carefully inspect the plate when installing
@tswyeung123453 жыл бұрын
I just got mine recently and it stayed flat and fit durock v2 stabs. So maybe this has improved in later batches?
@little_fluffy_clouds2 жыл бұрын
I just got mine and it was terrible, bowed the PCB badly when fitted. Sent it back and will stick to aluminium instead
@langotaroots19682 жыл бұрын
Hi! I've been looking for a few weeks how to get started with the first mechanical custom. After seeing your video I had no more doubts: I want it the same as yours! Really beautiful ... in the next days I get the pieces! Grande!!!
@nerdy13 жыл бұрын
Andy was right, the board was made for tactile thocks, linears are a bit lackluster in getting that pop sound. Nonetheless the before and after with mods sounded way better!~
@JaeyouPark3 жыл бұрын
100% agree with Andy. I feel like this board might pair nicely with a certain tactile panda switch..... 😏😏
@TechGuy42ilm3 жыл бұрын
Waiting on my white ice gmmk pro now. I can't wait for it. I have the drop shift and modded the shit out of and it sounds dang good but I think this will be on another level. I have my polor pandas and my halo clears so I can make my holy Panda switches. I also am going with matrix white pudding caps and the white aviator cable. I'm so excited I can hardly wait lol.
@needcoffeepls3 жыл бұрын
Very nice, the mods did wonders! And speaking of the d65, kbd just restocked. I know it's not a direct comparison, but you would recommend the gmmk pro over the d65? Purely on sound and typing feel (as I don't really mind either form factor)
@dloh0073 жыл бұрын
this sound... omg... saving this video for my build.
@JaeyouPark3 жыл бұрын
thank you! best of luck with your build :)
@GorillaBohne2 жыл бұрын
really like the sound :)
@bchang1263 жыл бұрын
how different was the typing experience using the PC plate vs the stock ALU? interested in getting a PC plate for mine!
@saab35draken393 жыл бұрын
The pc plate makes the sound a bit louder and less high pitched due to it being softer personally i prefer alu over pc and brass
@brianlam58472 жыл бұрын
If I were you, I would personally get a fr4 plate from AXCworks since the polycarbonate will bend your pcb.
@kyleb19583 жыл бұрын
The RGB difference between the Alu and PC plate is really quite noticable, I imagine the underglow would be quite uniform in dark conditions with the PC plate
@ceementality3 жыл бұрын
What would you recommend for gasket upgrade as I don’t wanna pay for kbdfans shipping for d65 gaskets
@AnonymousSpidey9 ай бұрын
As im watching this and needed to replace my gaskets on my board and they didnt sound the best but gladly glorious has replacements you can buy - Gmmk pro build Polycarbonate plate Akko cream blues - will upgrade to the new ones a nice thick foam pad inside 3 layers of tape with even a pe foam from stupid fish foam and eventually going To get the stupid fish foam plate replacement soon also Durock v2 stabs 👌
@HaiNguyen4083 жыл бұрын
great video as always
@JaeyouPark3 жыл бұрын
thank you Hai!
@bitcoyn Жыл бұрын
love what your doing here ❤ glad I found your videos....may I know what keycaps are those ?
@truuuupR3 жыл бұрын
Very nice. Will try the gasket upgrade on mine. Swapped my stabs out for durock V2's and removed the case foam so far. Running everglide aqua/water king switches which are buttery smooth. Debating removing the PCB foam as I do find the whole setup mutes the thock more than I'd like. More thock the better.
@little_fluffy_clouds2 жыл бұрын
I've also swapped to Durock v2s, holee modded and lubes and installed Aqua King switches (also lubed). I've also installed the aftermarket FR4 plate and removed the plate foam, but installed a thin layer of PE foam over the PCB, instead (it goes between the PCB and the plate, so it sits under the switches). Nice and thoccy now. I have the Stupidfish 3mm foam on the way, so I'll replace the case foam with that to see if it's better.
@mikes417203 жыл бұрын
Thanks for sharing the mods! I did the PC plate, standoff removal, and stabilizer upgrades to Durock V2s. I also removed the case and plate foam. I didn’t have D65 gaskets, so I went with a triple layer of stock gaskets on the bottom case, removed the diffusers, removed the PCB screws, and only used 4 case screws, lightly screwed in. Still a bit muted with linears but the added sound and flex is there, if not a bit unstable. Do the D65 gaskets provide a deeper sound over the stock gaskets or is it just mostly for the flex and feel?
@XDTheLaughingManXD3 жыл бұрын
Finally got mine, back to use the gasket upgrade.
@swiitchback38903 жыл бұрын
Great video! Will definitely try the gasket swap on mine :)
@daryljones37502 жыл бұрын
How easy did the PC plate fit over the durock stabs? did it require any filing/trimming? Love the vid :)
@magnus6683 Жыл бұрын
When I did this I had to file both the standard alu plate and pc plate to fit durock v2's.
@pittste883 жыл бұрын
I really like the gmmk because it’s reasonable custom board, like some of these 1500$ boards are just dumb
@MrUltimateX2 жыл бұрын
Damn how does your space bar sound so good? Mind sounds quite hollow, though I am rocking the aluminum plate for now. Wonder if the PC plate really makes all big of difference. Do you have any space bar foam by any chance?
@GregariousGrog3 жыл бұрын
that spacebar thonk so noice
@reynoldsieog98962 жыл бұрын
Just finished my GMMK Pro build with Ink Black V2 and Durock V2 Stablisiers. It's an awesome keyboard and at a great price. Some work needs put in from factory, but it's great. I like it a lot What kepcaps do you have? They're awesome.
@meowwow83403 жыл бұрын
@8:30 I didn't know that you're a magician... the gasket has suddenly gone... wow
@Ranger.TomGunna Жыл бұрын
I just ordered this and bought the Everclear Aqua King switches but I heard the stabs are horrible.. would you recommend the Durock Stabs or something else?
@peetzaBoy3 жыл бұрын
Very cool! I've got a GMMK Pro on its way so I'm excited to start tinkering with it. I don't have a whole lot of money so I'll have to do these upgrades slowly. if you were to rank the upgrades from most impactful to least impactful, how might that list look?
@timfederwitz3 жыл бұрын
I wouldn't try to speak for @Jaeyou Park, but I bet if you did nothing more than buy/add the Polycarbonate Plate and lube/band-aid mod the stabilizers, that would get you most of the way there. Also, not sure what switches you went with, but the Glorious Pandas (what I bought for it) are NOT lubed from the factory. So lube those too. You can get a tube of Super Lube on Amazon for $3 that will make a huge difference (if you are trying to stay on the cheap).
@JaeyouPark3 жыл бұрын
Hey congrats on your purchase! I would probably rank Stabs upgrade/tuning>PC Plate/standoff removal>Gasket upgrade. Definitely would recommend lubing your switches as well as it makes a noticeable difference as well!
@timfederwitz3 жыл бұрын
@@JaeyouPark I'm glad you commented here. I didn't realize you fully removed the standoffs, but that TOTALLY makes sense. LOL. More flex and thock
@peetzaBoy3 жыл бұрын
Thanks to both of ya'll! Yeah, money's tight with covid going on so it was hard to justify buying the barebones board alone. I'll snag some cheap lube and see if I can grab that PC plate as well. Thanks again :)
@timfederwitz3 жыл бұрын
@@peetzaBoy this is certainly NOT what enthusiasts would recommend, but I know from personal experience that it absolutely works to lube switches and make them sound thockier. www.amazon.com/Super-Lube-51010-Oil/dp/B000BXOGHY/ref=sr_1_10?dchild=1&keywords=super+lube&qid=1620063898&sr=8-10
@8bitsamurai62 жыл бұрын
Does anyone else ever just want to do a build for the fun of it. But not many instock boards. Want to pick one up just to a build. You can get an fr4 plate for this guy now too. Not sure if it any good though.
@jeffholmstrom87132 жыл бұрын
Very nice video, going to cop your build! Do you have the name of the vendor for the Metropolis set? Not sure what which one you bought from!
@TechGuy42ilm3 жыл бұрын
You also earned another subscriber!!
@JaeyouPark3 жыл бұрын
Thanks for the sub! 💛
@DashzRight3 жыл бұрын
Does the thicker gasket actually work? Logically I would assume that as the case and top plate are sooo tight together any gasket you put in there is going to be squeezed to a completely flat hard state…
@TheBeefedBaby3 жыл бұрын
Hey built my keyboard btw and it turned out really good the only bad thing was the stabilizers.
@JaeyouPark3 жыл бұрын
Congrats! You can always go back and tweak stabs haha. I am always tuning my stabs too. Which board did you go with?
@TheCaveman5k2 жыл бұрын
just noticed you did band-aid mod on your finger lmaooo
@SaikaBdo3 жыл бұрын
What stabilizer pads are those that you placed on the pcb? I have been trying to find those but havent had much luck.
@JaeyouPark3 жыл бұрын
They are actually just precut doublesided tapes for photo hanging lol and I just use the leftover parts of the deskeys gasket films as the foam portion!
@rusyaidirahman1192 жыл бұрын
you guys havent see keydoues nj80 budget price for wireless rgb but superb quality for the price. asmr stock sound
@kamabokogonpachiro7093 жыл бұрын
Niceee! Did you screw the PCB screws back? What does removing the standoffs do? Imma have to try this, but with doubling the gaskets using the spare from the box. I don’t have a d65 gasket to use lol.
@atlsoulja013 жыл бұрын
Off topic but what are you using to film? Looks incredible
@JaeyouPark3 жыл бұрын
thanks so much! My main set ups is the sony a6400 + sigma 30mm f1.4 :)
@marksironi33243 жыл бұрын
I use the PC plate and replaced stabs with Durock V2's. I left the foam and standoffs but I was going to take it apart at some point and try removing those as its still stiff (but sounds much better).
@user-qn1zj5bs5p2 жыл бұрын
just remove all the gasket and it will become more stiff , which is very good for me i love stiff typing feel
@nikolakostic56673 жыл бұрын
I found the PC plate makes the typing a bit less stiff but it sacrificed a lot of the sound. The board is already very muted, possibly due to its sturdiness (even with the plate foam removed) and the pc plate just made it sound cheaper/plasticky IMO. I would recommend owners try remove the plate foam and gaskets, and then use the alu plate for some added acoustics... That's what worked best for my tastes
@samshiff99653 жыл бұрын
Did I misunderstand or did you add gaskets on the board and the bottom of the pcb?
@denncardoso3 жыл бұрын
Great video. Next time, try to use timelapse videos to show you insert the switches and other build stuff related. Take care!
@PaladinSalt3 жыл бұрын
Great mods I did most of these myself, I would suggest you remove the bottom foam all together so you will actually get the flex from the gaskets.
@Pantifo3 жыл бұрын
Trying this on mine tonight
@ryanparker20773 жыл бұрын
@@Pantifo you think its better with or without the foam?
@FleyEnder Жыл бұрын
Hey sorry I’m quite the novice at keyboards but I was wondering what it was that made your space bar sound so much better afterwards? is it the stabilizers?
@min2youu3 жыл бұрын
what screwdriver head size did you use? I have some difficulties in removing the screws
@lukeAnthony-ci6rq11 ай бұрын
sounds better with aluminum plate but the space bar did improve
@benoice23843 жыл бұрын
So to do the gasket upgrade do you just replace ALL of the gaskets or just the ones on the bottom half of the case
@MontyS423 жыл бұрын
Can you provide some link for replacement gasket foam for the gmmk pro??
@JaeyouPark3 жыл бұрын
I used the leftover bits of this foam. If you don't have this, modular plate foam or shelfliner with doublesided tape works too! kbdfans.com/products/d65-gaskets?_pos=1&_sid=54495eb37&_ss=r
@MontyS423 жыл бұрын
@@JaeyouPark goddamntgat shipping is expensive
@Nicolium3 жыл бұрын
@@MontyS42 Maybe try with aliexpress fr.aliexpress.com/item/1005002300879578.html
@MontyS423 жыл бұрын
@@Nicolium ty
@jonfromsyracuse2 жыл бұрын
Were you able to get the Durock stabs to work clean with the PC plate? Seems that there is not optimal clearance from the PC plate to the stab wires with everywhere I am looking.
@cool_dude3292 жыл бұрын
How were you able to take out the screws? Mines don’t come out that easily and end up just kind of sliding around as I add in my magnetic screwdriver
@bukchoyfarmer25392 жыл бұрын
Damn I wish the glorious gmmk tkl had a metal shroud like that :(
@christophevers74763 жыл бұрын
Great video! It will be usefull when I receive mine. Why did you switched to your GF (or a friend) for the typing test? ;)
@wafflobufflo32803 жыл бұрын
Mate, those are his hands
@Koenv33 жыл бұрын
@@wafflobufflo3280 Building the board and the typing test are definitely two different people
@ShooterMcGapinFPV3 жыл бұрын
did your board bow like crazy with the pc plate on it? im worried to even use it. Idk if its the durock stabs or the plate itself
@keiz_2 жыл бұрын
There is some people in the community who made an FR4 plate that is available to purchase. Not certain how it compares to the PC plate, but they did add cuts in the design to allow for more flex.
@JaeyouPark2 жыл бұрын
fr4 is definitely one of my favourite materials. My friend hypekeyboards.ca/ actually sells them! I have a discount code "jaeyou" as well if you end up trying haha
@cerme923 жыл бұрын
I don't get the gasket upgrade mod. is it bad to have a fimr board? it is a matter of preference or that flex bring some improvements? Quite new in the game, tbh not quite sure about the benefitx of the gasket mount iteself
@Great_PatBingsoo3 жыл бұрын
Good video but a little more explanation would help, especially with the gasket part.
@SuFrostWill3 жыл бұрын
Yeah I'm wondering how to do that
@JaeyouPark3 жыл бұрын
yeah I totally agree as well. I would have to definitely consider doing voice-overs to provide more context!
@jerielcaranto58783 жыл бұрын
@@JaeyouPark hi! did you put the extra gaskets on top of the installed gaskets or on the side?
@stevensuryajaya75693 жыл бұрын
Bro i just wonder did the durock v2 stabs fit perfectly when you installed the plate? Since i’ve watched several videos stating that durock v2 wont fit into the gmmk pro plate. Nice mod btw!
@zero6042 жыл бұрын
It doesn't fit with the aluminum plate but works fine with the PC. They have since made a V2 of the aluminum plate that fixed this.
@Chocofank3 жыл бұрын
I think what I heard is the difference of the plates not the gasket...
@iLuvCats Жыл бұрын
It really bothers me how you took the first screws out. Like, what if you dropped one?
@azurezinc3 жыл бұрын
Hi sorry I couldn't really tell from the video but where did you put the d65 gaskets on? 2 on the sides under the pcb and the rest on top of the existing gaskets?
@the_steko2 жыл бұрын
Duddeee,, those keycapsy can yoi get the same ones, but double shot so the letters are tranasparent like normal keyboards
@n3o3213 жыл бұрын
could i ask what blue mat you're using for your desk mat? also, how are the screws? are they solid? saw a few videos saying the screws are prone to breaking/snapping
@n3o3213 жыл бұрын
nvm just saw you listed the deskmat in the descriptions!
@gravex3 жыл бұрын
i have the exact same build except my plate is making the space bar stuck (it doesnt go back up) ami doing something wrong?
@AJTamiSan3 жыл бұрын
Hello! The way I see it in the video, What screws did you install in the PC Plate and PCB assembly?
@get_troll3 жыл бұрын
i mean not fully tighten the screw work better than the gasket upgrade. just leave room for the gasket to bounce
@Soryai_Sarutobi Жыл бұрын
can you possibly provide a link to the exact Keycap set please? I would really like to purchase it!
@eternalgreed67153 жыл бұрын
How you use gmmk pro with macbook? How you press option and command button on it ? Is win bottun works as command and alt as option? Thanks!
@theboyedson2 жыл бұрын
what kind of tape or materials did you use under the stabilizers?
@marwanfikrat77162 жыл бұрын
Wondering the same thing
@xampleman3 жыл бұрын
i mean is the board decent as is...seems like a ton of work. little overwhelming..... my hands are not very stable either due to medical issuies... i daily drive the Drop CTRL and just got my GMMK pro with pandas and GMK Laser keycaps.... didnt realize the stabs were screw in so upgrading has been less of an option for me
@gloktopuss56283 жыл бұрын
im worried because i ordered the flex batch of the gmmk pro but I also ordered durock v2 stabs and I've heard from some people that the included allu plate is a really tight fit or it wont fit at all .
@luuuser98033 жыл бұрын
Can i cut off the parts on the plate that wraps around the pcb to give it more flex? just curious if the material is easy to cut off to provide more flexibility
@legion5643 жыл бұрын
MONKAS MONKAS MONKAS
@JaeyouPark3 жыл бұрын
This is definitely poggers as people nowadays say it - am I right??
@alicetong31592 жыл бұрын
Is there any other way to get the gaskets without buying another board?
@jaden12162 жыл бұрын
I did the tape mod and my keyboard stopped working…
@Moni-ValMar2 жыл бұрын
Where can i get new gaskets? can i find good ones on amazon? (It needs to ship to Colombia)
@nvn30423 жыл бұрын
Can i ask what what is the name of white thing you apply on PCB and under stab and purpose of it ?
@Jazzero89 Жыл бұрын
Hi, the keycaps in this built are insane. I need the exact name please!