45° degree offset EXPLAINED!

Рет қаралды 4,059

3 жыл бұрын

45° degree offset EXPLAINED!
This is a more in depth video to show why we use the numbers we do to figure this offset.
Remember....OFFSET = ADVANCE • 1.414 = TRAVEL
1.414

Пікірлер: 21

@Sam-qu7jx 3 жыл бұрын

This the second video I seen on your channel and Man am i thankful to found your channel so i have an idea of what to be involved with and learning in the plumbing trade. Stay solid stay blessed g, great content

@JoonRhee 3 жыл бұрын

Wow appreciate the love friend! Stay tuned and ask any questions mate! Glad this helps

@user-lk2di2ct5c Ай бұрын

good. need more info buy the electric references U glys has alot about bending pipe $15

@leonwoods4052 6 ай бұрын

Well explained, thank you.

@JoonRhee 6 ай бұрын

Glad it helped! Thanks for dropping a line. Any questions just shoot!

@leonwoods4052 6 ай бұрын

@@JoonRhee thanks again . I have a question, what about fall percentage of a pipe ,grade ,percent ,that stuff.

@JoonRhee 6 ай бұрын

@@leonwoods4052 that's all dictated by pipe size! Our code says - 1/4" per foot up 0 - 2 1/2" pipe...1/8" - from 3-6" pipe and 1/16 - on anything above that. But those are code.questions per your states code laws

@leonwoods4052 6 ай бұрын

@JoonRhee Right on Brother, you're on it. Gladly appreciated.

@denvercharlebois699 10 ай бұрын

Joon if you have a 45 degree 1 1/2" fitting and a 90 degree 1 1/2" fitting. Would you still measure centre to centre and times it by 1.414 and subtract the fittings or is the multiplier only used if you use 2 45 degree fittings?

@JoonRhee 10 ай бұрын

Let me think about that. I've never done that offset math. But 1.414 for sure is only between to 45 degree fittings

@denvercharlebois699 10 ай бұрын

@@JoonRhee So a 90 fitting and a 45 degree fitting can't use a multiplier?

@denvercharlebois699 10 ай бұрын

Apparently a 5th term apprentice was saying you can due to it still being a triangle. Which to be fair I don't fully understand what he means by that.

@JoonRhee 10 ай бұрын

@@denvercharlebois699 I am sure you can...but just cause you can doesn't mean you should. I've only done that to hit a rough in on a p trap stub out for a sink.

@denvercharlebois699 10 ай бұрын

@@JoonRhee Do you know of any sites to find the take off for copper fittings like a 1 1/2" 90?

@sloppyjonuts9162 3 жыл бұрын

So take off and off set are the same thing ?

@JoonRhee 3 жыл бұрын

Hey sloppy jonuts! Thanks for the question and negative you are incorrect. Take off is apart of your offset. It's apart of the equations once your travel piece is calculated. I'll make another video clarifying this. I made the same mistake too. But you'll get it

@deonterichardson2814 3 жыл бұрын

Hey bro how have you been doing? How’s work been?

@JoonRhee 3 жыл бұрын

Cold man! Ice cold doing the under ground! Haha but still alive and learning. How about you?

@deonterichardson2814 3 жыл бұрын

@@JoonRhee hahaha I feel it! And same . Just waiting patiently until I can get in and be out there with you and tell you about my experiences and what I’m learning I’m so ready!!