4l60e overhaul

Рет қаралды 74,879

3 жыл бұрын

This video goes through a 4L60E from top to bottom and it follows along with the service manual. In this video, you will see factory measurements, specifications, and inspection. I also demonstrate the common vacuum testing locations. This video is used in the SIU Automotive transmissions course when students want to overhaul a 4L60E. They are required to watch this video first before tearing into the unit.

Пікірлер: 49

@kasems1536 19 күн бұрын

Very clear&cut, thanks a lot, Greetings from Bangkok.

@warrenmoore3006 Жыл бұрын

Thanks-a-MiL Mr. Siu✨You PATIENTly went through a Few Technical Details No-one else Has Ever illustrated..👍

@MarioDallaRiva 3 жыл бұрын

Extremely well presented! Having watched many of your other videos in the Auto Transmission playlist, the voiceover was brilliantly executed. Thanks!

@siuautomotive 3 жыл бұрын

Thanks! So you prefer the voiceover method?

@MarioDallaRiva 3 жыл бұрын

Live is always best! Your voiceover was nicely choreographed with the video content. I think it adds value to that which you're describing. You clearly know your stuff and present very well. The engineering that's gone into these transmissions is impressive. It's crazy to think the BEVs use only a single gear reduction, except for the Porsche Taycan I believe, and do away with the need for a transmission.

@spencemcmorris7686 2 жыл бұрын

@@siuautomotive I prefer live method, but you did very good with the voice over. I've watched it 2 or 3 times. Where can I go to get certified to rebuild transmission? Been studying for over a year on 4l60e. I'm pretty confident in it.

@RandomGuyDan 2 жыл бұрын

As a junior in high school in 1981 I really wanted to attend the SIU automotive program after graduation. My parents (SIU grads, I was born in Carbondale) wanted me to get a conventional degree. I have done well, but still regret not following my heart. In the next couple weeks I'll begin a rebuild of the 4l60E from my 2004 Envoy XUV.

@bigstuff52 6 ай бұрын

Thanks for uploading..What a beautiful shop..

@bundymc502 Жыл бұрын

Great video is an understatement 👌🏼👍🏼👌🏼👍🏼👌🏼👍🏼

@casualobserver620 11 ай бұрын

One clarification is that if the pin that secures the band has not been removed first, or the band is not cleared the retainer pin from inside the case, you AIN'T gonna simply reach in and remove the drums.

@speedfreak1161 7 ай бұрын

Awesome video, simple terminology and good video , cheers

@gamersmadness207 2 жыл бұрын

Very helpful on my build with the gears and bearings at the bottom of the case thank you

@lelandharper2099 2 жыл бұрын

Great video, best I’ve seen!

@diyguy446 6 ай бұрын

Wow goooooot joooooob!!!!!!

@joelrugg Жыл бұрын

Awesome instruction it really helped me

@alexanderstefanxandraswedi5835 2 жыл бұрын

Great job

@OlegIgorevich95 3 жыл бұрын

Спасибо за отличное видео)))

@pbooth001 2 жыл бұрын

Well done.

@MeaHeaR 2 жыл бұрын

at 54:17 I likéd hów you triéd to put thé Snáp-Ring on ovér thé Crow-Bár 😃😃😃😃😃😁😁👍👍👍

@sanchezjo78 2 жыл бұрын

Well explained video. I having a problem with my trans is liking fluid from the axle shaft where can I get info to fix that problem and get the gasket..thk

@james102377 Жыл бұрын

Is there a way to air check the pump stator seal rings after installing the pump to make sure they didn't get chopped during installation?

@humbertoramirez7799 Жыл бұрын

thanks

@AB-gi9gu 7 ай бұрын

Used this vid to help me rebuild my 2003 4l60e. Unfortunately i guess i boned up somewhere, because i have an extremely delayed 1-2 shift. Do you have any idea where i might have messed up?

@purityobot5390 Жыл бұрын

Please I want to know if the 4L60E 4x4 Tail Output Shaft turns anticlockwise only

@Spector_NS5_RD 3 жыл бұрын

Can the case saver also be referred to as an "anti-clunk spring"?

@siuautomotive 3 жыл бұрын

Yes sir! It keeps the low roller housing lugs in contact with the case lugs so they don’t “clunk” when the trans downshifts from 2nd to 1st. If it wasn’t there, it’d eventually beat the case lugs out.

@matermark 2 жыл бұрын

Did you R&R the rear case bushing?

@mikeverything4098 2 жыл бұрын

i have a late 90s 2 piece 2wd 4l60e out of a pontiac firebird i need to replace the pumps this will be my first tranny juob how should i go about it ?

@EGOR1100 2 жыл бұрын

dude, cool video, very informative. but do you have similar video for 1995 Tahoe 4L60E tranmission?

@Twan5.7 2 жыл бұрын

It should be about the same way

@siuautomotive 2 жыл бұрын

The main difference is a few things in the valve body. Don't get a spacer plate for anything but a 1995. The 3-2 downshift solenoid is pulse width modulated and not on/off like on the later units. But for the most part, rebuilding it is the same.

@AntonioMartinez-pr3wb 10 ай бұрын

If and when i do my rebuild, do i need a new torque converter or can i use the old one i heard you mentioned something like this at the end, thanks for the video helping me and im sure plenty others, cheers

@davepetrakos1192 9 күн бұрын

New or remanufactured as stated in video. I believe one gets what is paid for. An old TC that fails in a rebuilt transmission means Everything has to get rebuilt, again! Purge the cooler while the lines are disconnected.

@micthegreasemonkey2918 3 жыл бұрын

Thnk u 4 the clip but i would hav appreciated u telling us diyers how to do things @ home ! Like sizeing the teflon orings ect.

@siuautomotive 3 жыл бұрын

You can align the pump halves with hose clamps. The 2/4 servo needs 1/16 to 1/8" movement when installed and pressing on the cover. The teflon seals can be resized using electrical tape and a hose clamp, or sometimes even a zip tie. If the rings are in good shape, just reuse them. Many builders don't change those rings. They usually last forever. Other than that, there are not many tools needed.

@martinez1701a 3 жыл бұрын

Does anybody know if it matters the position of the rear case bushing when installed? I installed my bushing and lined up one of the slots of the bushing with the oil slot of the case, didnt know if the slot position of the bushing was important.

@siuautomotive 3 жыл бұрын

I don’t think it matters, but I always line up the slot as well! But I’ve seen them installed from the factory in random positions.

@martinez1701a 3 жыл бұрын

@@siuautomotive ive been thinking twice about the 4l60e im building lol some guys say you gotta line up this way or that way then Ive been seeing professional builders just through them in any which way LOL i guess I shouldnt worry thanks.

@craigj.651 2 жыл бұрын

I dont know if it matters but they arent lined up from the factory, I marked the spot with marker an took pictures an put the new one in the same position.

@DEVUNK88 5 ай бұрын

How similar are the 4L60 and 4L80 ?

@hermanjones4124 Жыл бұрын

Hello i have enjoyed your video and find it to be very useful tool, i have a couple questions if you don't mind i rebuilt my 4L60E and reverse stopped working and my sunshell is good i replaced it in the rebuild also the 3-4 clutches burnt up again as to that is the cause of original failure. CAN YOU HELP ??? THANKS

@siuautomotive Жыл бұрын

The 3-4 burn up is common on these. The input shaft can get loose and that causes 3rd oil to leak out. The valve body has a few valves that cause a loss of 3rd oil. The the abuse valve plugs, worn afl bore, and the capsulated check ball in the case.

@beckydeanmcleod1017 2 жыл бұрын

I would like to know how to make the bushing o washer stay on the back of the pump when rebuilding the transmission

@siuautomotive 2 жыл бұрын

Vasoline or trans assembly lube. It allows you to stick bearings and shims in place for assembly.

@MeaHeaR 2 жыл бұрын

At 48:50 I noticéd you didn't replace thé vâlvé body Filtér Screen (s). Is this necessary to do or not required generally ????

@siuautomotive 2 жыл бұрын

I usually get a new plate because the check balls beat up the plate too much. The new plates have a gasket bonded to the plate and built in filters. But if I’m reusing a plate, I’ll put the new screens that come in the overhaul kit.

@MeaHeaR 2 жыл бұрын

@@siuautomotive oh thats useful and interesting, thanxx 👦🏿👍🏿