They are definitely some good looking trucks

Thanks and hopefully you enjoy it

Thanks for watching and I’m glad they could help and I wish you the best of luck on finding one. Just keep an eye out and hopefully something good will come up

@@TruckLifeProductions thank You so much and have a great weekend 👍

Sounds like a good truck

Thanks man!! That’s awesome and I know the struggle sine my 10th Gen F150 has the sliding back window

It's worth it to have the beer window

It will bolt to the 02-05 grille support with the exception of 2 bolts at the bottom, it also has a gap on the side beside the headlights, so I am going to find a 06-08 grille support to swap over to and it should eliminate that. You will still have the gap at the bottom corners, but it you can live with that I’d say go for it. I personally like the 06-08 grille better than the 02-05

@@TruckLifeProductions awesomean I appreciate the quick response...you have a sub from me for sure thank you

@@mitchellmartinez8066 absolutely and thanks, hope you enjoy the content 👍🏻

That’s awesome, yeah the beds are bad for it but they definitely look good lifted

Thanks, I bought them through Custom Offsets. They’re 20x12 -51 Vision Widow in satin black

Thanks. It has a 2” Rough Country leveling kit

Mine is about to hit 262k so I would say yes especially if they are well maintained and not dogged out. Sounds like a decent price but before you buy you should check it throughly, that goes with any vehicle. The only problem I would have a concern with would be head gasket being replaced, usually that comes from having a blown head gasket which then causes the oil and antifreeze to mix so that would be the cause of changing the oil and filter. Definitely a plus with no rust on the bed but you should take a small magnet and test to make sure that it hasn’t been fixed with bondo, when I got mine the bed sides looked perfect and over the next few years they started to rust out so as far as tips keep any road salt washed away from the bed in the winter if you live in an area that you get snow. Another tip would be to let it idle after you park for 30secs to a min before you shut it off so it doesn’t heat soak the engine, one of their flaws is a ring around the valve seals that can drop out from excessive heat or overheating. Keep me updated and good luck!

@@TruckLifeProductions Thank you for the tips ! , ill definitely let you know how things end up going , but as im looking through the car fax , 191k miles , but when i said the headgasket got replaced , incorrect , it was actually the valve cover gasket that was replaced, would that be less concerning?? also ignition coils were replaced as well one more thing i noticed while i drove it around , oil temp gauge would go from the middle mark up to about 3/4 of the gauge every time i accelerate any idea on that one? that was the only thing i encountered while driving , i will get a code reader and see if anything pops up.

@@TJT153 yes that is less concerning and perfectly normal, they could’ve been leaking. Mine were at one time and I replaced them. It’s good to change ignition coils when they get higher miles on them because they don’t work as well as brand new ones. Definitely run a diagnostic test to check for any codes that may not be showing up. The oil pressure gauge can fluctuate when accelerating that is normal.

@@TruckLifeProductions just got back from running codes for the truck , I got 3 codes 1. C2206 vehicle configuration mismatch 2. U0141 Lost communication with FCM 3. U0100 lost communication with ECM/PCM. Are these concerning codes ?

@@TJT153 C2206 Code - when the Anti-Lock Brake System (ABS) Module detects the signal from the gateway module relevant for vehicle characteristic is missing for a period greater than the specified fault duration. Code U0141 pertains to the BCM "A" or the wiring to the BCM from the engine control module (ECM). ... The code may be detected when the ECM has not received an emission-related CAN signal from the BCM for at least two seconds. The generic OBD trouble code U0100 is a serious situation where the signals between the electronic control module (ECM) or the powertrain control module (PCM) and a particular module have been lost. There could also be a problem with the CAN bus wiring disrupting communications. The vehicle will simply shut off at any time and will not restart as long as communications are interrupted. Most everything on present day vehicles is computer controlled. The engine and drivetrain are completely controlled by a computer network, its modules and actuators. The U0100 code is generic inasmuch as it has the same frame of reference on all vehicles. Somewhere within the CAN bus network (Controller Area Network) an electrical connector, wiring harness, module has failed, or the computer has crashed. The CAN bus allows microcontrollers and modules, as well as other devices communicate independently of a host computer. The CAN bus was designed for the automobile specifically.

5.7 Hemi

Leveled

From eBay, I just typed in smoked headlights for 02-05 Ram

5 on sides 20 on windshield w/ 5% brow 20 over 5 on rear window

Awesome, yep the 5.7 Hemi, let me know if you have any more questions.