6.0 Powerstroke Injector Upgrade 600HP Build

Рет қаралды 769

4 ай бұрын

In this video we briefly talk about our 6.0 Powerstroke Injector Upgrade 600HP Build. We are doing a 6.0 powerstroke injector upgrade. The injector install is being doing while the shop is putting the heads on.
Merch Stores below
teespring.com/stores/60-bros-...
Check out our Amazon merch store
www.amazon.com/s?rh=n%3A71411...
Check out our sponsor Turbo Time USA
Don't forget to use coupon code SIX0BROS for 5% OFF your custom turbo!!
Affiliate link (automatically applies discount)
turbotimeusa.com/SIX0BROS
BD Diesel Throttle sensativy booster
tsb.bddiesel.com/
affiliate link for archoil amzn.to/2TtUVEO
6.0 Powerstroke build list for both project trucks affiliate links listed below
Turbo Time USA 66m Predator velocity port VGT turbo
kill devil diesel o ring heads and pushrods
colt stage 2 cam
warren diesel 175/stock injectors
Fass fuel system with sump amzn.to/2SXm5ik
cnc fab stage 1 hpop
S&B intake amzn.to/2XKKyea
Mishimoto intercooler pipes amzn.to/2XOpdAx
Intake elbow amzn.to/2XQTuio
MBRP intercooler pipe amzn.to/2SWjFQN
no limit fab intercooler pipe
csf 6028 intercooler www.ebay.com/p/Intercooler-CS... -non affiliate link
mishimoto degas bottle amzn.to/2F5iICc
mishimoto performance radiator amzn.to/2UslfLX
odawg s3r ported intake manifold amzn.to/2O0f6nD
odawg s2r ported intake manifold amzn.to/2ETf115
BD diesel exhaust manifolds amzn.to/2u0FdSp
BD diesel y pipe amzn.to/2O06HAH
4 inch magnaflow exhaust amzn.to/2XQuPdI
alternate to the magnaflow exhaust amzn.to/2F5UuaI
rough country 2.5 inch leveling kit amzn.to/2F6C61C
BDS dual add a leaf (rear)
firestone ride rite air bags amzn.to/2ESjn8Q
fuel sledge 20x10, -18 offset amzn.to/2NZrdl5
spyder headlights amzn.to/2NW7vGZ
spyder tail lights amzn.to/2EVlwR6
08 tow mirror amzn.to/2F5I5DL

Пікірлер: 17

@Outlandandassociates 4 ай бұрын

Look into the BD Tap shift so you can lock it in gear and you'll get to see how much break force it adss over the minimal stock setting. It's cool to see the power pull and the exhaust break kick in. I bet you could make a fun video on just that topic.

@six0bros 4 ай бұрын

I haven't looked at the bd tap shift in a while but doesn't that update the shifter to similar to what the newer trucks have?

@six0bros 4 ай бұрын

@Outlandandassociates I'll have to put it on the list. For this event I'll just have a tune for it, but that ND shifter has always had me curious

@Doom6.0 4 ай бұрын

YESSSSSSSSSS!!! 😎🇺🇸🇺🇸🇺🇸

@six0bros 4 ай бұрын

Hey man how are you doing. I'm excited for these new injectors man!

@bobuncle8704 4 ай бұрын

Looking forward to see how the dyno run goes.

@six0bros 4 ай бұрын

Me too man I'm excited to put it back on one and see how it does. Built trans, and engine I just need to make sure my calipers are not sticking this time

@bobuncle8704 4 ай бұрын

@@six0bros Absolutely. We had that on a circle track car back in the day. Turned out to be the flex hose, after going through 3 calliper.

@six0bros 4 ай бұрын

@bobuncle8704 I had all my lines replaced but that was before it was down for so long. However it was just a bad caliper before. My dad was going through calipers regularly for a bit turned out to be bad hoses

@markmorris6208 4 ай бұрын

I can't believe people pay $1k for stock remans to over $3k for custom injectors. It's not like there's 100's of builders. If you have any type of mechanical ability an know what parts you need. You can have a set of injectors for just over $1k

@six0bros 4 ай бұрын

I have learned a lot about these injectors and how to build them now but some of the parts are not as easy to find or get.

@Itsa_Mea 4 ай бұрын

Dyno event in NJ? How do I not know about this.

@six0bros 4 ай бұрын

April 13th Skyland stadium big time kustoms 7th annual dyno for charity event

@Itsa_Mea 4 ай бұрын

@@six0bros oh that's why. North Jersey.

@six0bros 4 ай бұрын

@Itsa_Mea they are close to turbo time. Turbo Time is sponsor the trucks entry provided everything is going smoothly once it's back. It's really last minute for the truck but hoping for like 3 weeks or so of good running before I put it on the rollers