6 SHARKBITE Mistakes NOT To Make!

6 SHARKBITE Mistakes NOT To Make! | GOT2LEARN

Рет қаралды 2,813,040

Күн бұрын

Sharkbite fittings are awesome, but they must have the proper installation procedures like any other joining method, here are 6 common mistakes NOT to make, that'll help you get a leak free connection!
Join my plumbing forum for FREE!
got2learn.freeforums.net/
Insertion depth chart: www.sharkbite.com/pipe-insert...
Amazon affiliate links to all the products I used in this video:
Silicone Grease: amzn.to/2YmDeqv
Sharkbite Pipe Cutters: amzn.to/30dspL0
Deburr & Depth Gauge Tool: amzn.to/2LG5krm
AutoCut Pipe Cutter 1/2": amzn.to/2XlyqAn
AutoCut Pipe Cutter 3/4: amzn.to/3gPmhhz
Disconnect Tongs (set of 3 sizes): amzn.to/2LLcZVz
Disconnect Clip (set of 5 sizes): amzn.to/31JO2PA
Sharkbite Self-Adhesive Tape: amzn.to/31J3VGe
Pencil reamer: amzn.to/2tBuhKW
All-in-one deburring tool (blue): amzn.to/2U3J1xu
Start - 00:00
Insertion depth mark - 00:19
Not deburring - 00:55
Not aligned - 01:25
Pipe/fitting not clean - 01:55
Soft copper - 02:28
Reusability - 03:02
DISCLAIMER: Got2Learn is NOT responsible for any damage done to a property of which the plumbing wasn't done by a professional, I do not recommend doing your own plumbing if you are unsure about what you are doing, always hire a LICENSED contractor when doing any type of plumbing so you can be covered by insurances if something does happen, these videos are for entertainment purposes only!

Пікірлер: 1 400

@fistpunder 2 жыл бұрын

I've worked in the HVAC field over 30 years. I'm still watching, reading and learning from books, other technicians and even videos like yours. You can always learn something new, even if it is a small detail, it can mean big savings in time and labor later. Thanks for the video.

@Got2Learn 2 жыл бұрын

😇😇😇

@Mouse_007 2 жыл бұрын

I'm 30 year hvac mechanic too and thought : Hey I might learn something new about sharkbite fittings. Never too old to learn something new.

@velodim 2 жыл бұрын

I am in HVAC business. Haven't even used regular caplings in a while. Just use a tool to expand copper pipe and than stick one into other

@twentydixoncider7443 2 жыл бұрын

After 30 years as an HVAC tech you should probably know damn near everything about your job by now and shark bites aren't very professional they're quick and easy but they're not the correct way, they really should only be used in a pinch when It comes to copper solder it, when it comes to PVC or CPVC glue it, When it comes to pex throw it in the trash lol jk crimp that shit

@idonttext9783 2 жыл бұрын

no dude shark bites are garbage lol

@5fiveful 3 жыл бұрын

The guy on this video could script videos for many products. He is excellent. He knows what to say, what not to say. He speaks clearly. He doesn't use annoying filler words like, "and, um...".

@Got2Learn 3 жыл бұрын

Thank you so much for your kind comments Susan!

@rmd2387 2 жыл бұрын

Good to see others use my tool of choice, the ice pick

@jonjacobjingleheimerschmid3798 2 жыл бұрын

You mean!!!???? It's NOT just for shotgunnin beers!!???

@burpostockings 2 жыл бұрын

I use my teeth.

@jackmaddesty 2 жыл бұрын

No touch karate with a whole lotta chi… works every time. Be like water-Bruce Lee

@julyguynj 2 жыл бұрын

😅😄😂🤣

@bryenlink 4 ай бұрын

Don't mean to flex but I just picked up the new Festool Arctic22 Ice Pick.

@boxsterman77 11 ай бұрын

This was SOOO helpful. The warning about soft copper was especially useful and explains a current issue I'm having.

@mitchellm4746 9 ай бұрын

What issue are you having? I just realized I installed a skarkbite on soft copper, and I'm hoping I don't have any issues. So far so good though.

@spymasterjr7185 3 жыл бұрын

lol, i love the "let me kick the pipe into the fitting" part, that cracked me up m8. But seriously, good vid as always

@Got2Learn 3 жыл бұрын

I've seen it done, and it's not even funny lol 🤣🤣

@2014cwajts71 3 жыл бұрын

I would've used the ice pick.

@TheSevenJr86 3 жыл бұрын

Works like a charm with galvanized unions!

@beotheguitarist 3 жыл бұрын

Awesome video as always. Learned so much from your videos and will continue to learn. I've never used sharkbite fittings, but have always used propress and solder fittings. Your videos on soldering have helped me to do it correctly! Cool man!

@Got2Learn 3 жыл бұрын

😊😊😊

@T.E.P. 3 жыл бұрын

you do a fantastic job on all your videos and very excited to see this channel grow ... and your sense of humor is so fun too. not many people can pull that off

@Got2Learn 3 жыл бұрын

Thank you so much @Thor Eric, a true loyal fan you are :)

@brookswest3306 3 жыл бұрын

Excellent advice with a most clever sense of humor . It was direct and clear . Post others like this and you will own the fixit internet . Well done !

@Got2Learn 3 жыл бұрын

🤩🤩🤩

@nvlvdave Жыл бұрын

Great video and great info! I especially like your super-plausible examples, like drilling the stud with the fittings laying there. Great job!

@henryaxe1 3 жыл бұрын

“Cut with an ice pick”!, outstanding! Great vid as always.

@Got2Learn 3 жыл бұрын

🤣🤣🤣👍🤩👍

@butters4596 3 жыл бұрын

Ice pick made my day 👍

@Got2Learn 3 жыл бұрын

🤣🤣🤣

@daviesoyetunji9994 2 жыл бұрын

Or smash with ice breaker 😀

@YouTubeStudio101 3 жыл бұрын

By far the best video showing the use of copper to CPVC via a shark bite. This was exactly what I was looking for. Thank you!!

@Got2Learn 3 жыл бұрын

Awesome 🤩🤩🤩

@robertanderson2370 2 жыл бұрын

I repiped from galvanized to PEX using sharkbites, I wish that war was only a weekend, lol. Good points, and things I did not encounter since I was not using copper in any way. From my own experience, I would add a couple of things. First, don't expect PEX to hold itself as well as metal pipe. You are going to have to strap and support it through long runs and when you might have counted on a rigid pipe to provide some passive stability on fixtures, you will be disappointed. Since we're on the topic of strapping, don't use wire to tie PEX along floor joists and such. Over time, it will cut through the PEX slowly. Next, don't let the PEX touch the soil or become exposed to even partial light, the pipe will decay quickly. Finally, if you are repiping be aware that the builder might have used your metal piping as a ground for your wiring. You may need to carry a ground wire to where your metal piping still exists and connects underground, for me, it was the supply line from the utilities district. You would be safer buying and driving down a ground stake and connect grounds to that to protect your house from electrical fire...All that being said, I loved the advantages of PEX and the price and durability was comparable to favorable over metal piping. It has been ten years now, and no troubles.

@kreamowheat 3 жыл бұрын

Always ensure your tip is clean before inserting.... wisdom of the age.

@Got2Learn 3 жыл бұрын

I had to do it 🤣

@skully70 3 жыл бұрын

"Get silicone lubricant so that it is easier to go in" is a close second. Especially for older parts!

@Got2Learn 3 жыл бұрын

🤣🤣🤣

@chrisvanweele6641 3 жыл бұрын

Yah that's why cavemen dragged their women home by the hair and not by the feet they don't fill up with dirt

@jacobcarraway1989 3 жыл бұрын

Make sure you have you Pipe Dope handy!

@lquinn7212 3 жыл бұрын

Very informative video. Using an ice pick...lol! Making sure the end of pipe is clean before insertion into fitting. Also good advice for the bedroom.😯 Thank you for cutting to the chase and not having annoying banjo music.

@Got2Learn 3 жыл бұрын

Awesome man, thx!!! 👌👌👌

@tommytwo9051 Жыл бұрын

I’m using the SharkBite end stop product for the first time. Your video made the process so much easier. Thank you!

@boatrs6102 Жыл бұрын

I’ve been plumbing for 27 years and this is the best explanation video I’ve seen yet!! Great video, hands down! And I love the sarcasm. Because I myself in my early years have done one of those things 😂 . Let’s keep it 💯

@maaly8111 2 жыл бұрын

Awesome. Had a plumber ignore all these steps using shark bites and cause more problems. Fixing it myself using these tips. Thank you!!

@johnmoniz2715 2 жыл бұрын

He prob isn’t a licensed plumber if he’s using sharkbites to do his plumbing work.

@maaly8111 2 жыл бұрын

@@johnmoniz2715 I found that out the hard way.

@joem5643 3 жыл бұрын

Been using these for a few years and they work very well specially on repairs where soldering is almost impossible when the pipes have to much water in them. It only takes a few drops of water to ruin a soldering job, then you have to start all over.

@Got2Learn 3 жыл бұрын

😉

@integr8er66 3 жыл бұрын

When water is a problem stuff some wadded up bread in there then solder it up before it melts away. It will flush right out when you charge the line later

@bernardkinsky1637 3 жыл бұрын

I use white bread make a dough ball and put it in the dripping pipe ,solder and flush out the dough

@charleshank8573 2 жыл бұрын

I just want to thank you for posting this your videos they are very helpful for a person such as myself that does not know plumbing all that well. I have learned a lot from your videos.and I want to personally thank you!!!!! have a great day and God bless.

@Got2Learn 2 жыл бұрын

So nice of you!!!

@paulreed2526 2 жыл бұрын

Not going to lie…. I actually laughed out loud when you kicked the pipe. Great video!

@WJHandyDad 3 жыл бұрын

great sense of humor while still teaching us

@Got2Learn 3 жыл бұрын

😉😉😉

@mat4410 9 ай бұрын

Best SharkBite tips video I’ve seen. Glad you added no Vaseline to it, too many folk show no mercy to the beloved “O” ring. You covered all I can think of Bro!

@Got2Learn 9 ай бұрын

Wow, thank you!

@deeray1974 2 жыл бұрын

This vid was hilarious!!😂😂😂 I've been using them for about 2 years now and haven't seen such craziness!!! "But.. I kicked it in.."😂⏬😂😂😂

@kristenaasrud533 3 жыл бұрын

U can actually use those parts on soft cu pipes, but you have to put in a support sleeve inside the pipe 👍🏼

@davidcraft4909 3 жыл бұрын

Thanks again I just learned that there is soft and hard copper. unfortunately, I believe I have soft copper and galvanized pipes ok. so like yeah I'm learning and figuring out what can and cannot be done and eventually after 9000 hours of research I will have a plan. Its funny how I keep finding more and more videos from your channel that is very relevant. thanks.

@Got2Learn 3 жыл бұрын

🙏🙏🙏

@paulmaxwell8851 3 жыл бұрын

I see a lot of old-school plumbers are on this page, guys who love to rant about Sharkbite fittings. Fact: Sharkbite fittings have their place. They are reliable, durable and cost effective when labor is factored in. They can withstand temperature extremes, and can be released during renovations or repairs. I see the same resistance to new ideas from old-school carpenters. Just don't hire an old-school guy! Hire someone who is up to speed instead. I've been plumbing for the last forty-five or so years. I have never hesitated to keep my mind open to new ideas, and when Sharkbites came along I gave them a try. Installed properly, they are dependable. Sure, installed by a sloppy guy who doesn't care, they'll leak.

@Got2Learn 3 жыл бұрын

Well said!

@kamron_thurmond 3 жыл бұрын

Yes, same with a glue(weld), soldered, or threaded fitting too. A leak is possible in any fitting if not properly installed.

@redlobster4841 2 жыл бұрын

You better have good insurance on your house if you plan to use these in your house

@Soldier1234ish 2 жыл бұрын

@@redlobster4841 properly installed these fittings are great, i have multiple shark bite fittings in my house going from copper to PEX where repairs were needed in my basement. In two years, living in North Dakota, a state with 150 degree temperature change I haven't had a single problem

@ProjectStrum 2 жыл бұрын

Got ones all over my house ,12 yrs now no problem .

@AmitSingh-zn1kz 2 жыл бұрын

Brief but very helpful and well-made video. Thank you.

@WeazelJaguar Жыл бұрын

I made the very first mistake, so I will disassemble, mark the depth and do it again! Thanks for the tips!

@rmbjr60 3 жыл бұрын

1:07 LOL! I was like, "wait ... what did I just hear???" The perfect all-around tool I guess! I want one!

@Got2Learn 3 жыл бұрын

🤣🤣🤣👌

@ApoJake13 3 жыл бұрын

I cut my copper pipes with an ice pick all the time. Highly recommended! :P

@Kainosktisis 3 жыл бұрын

I never install a Shark bite fitting without plumbing grease, you will inadvertently damage the o-ring shorting it's life, once it is debured properly, remember that a file can leave marks that can cut the o-ring, that's where the Plumbing grease comes in, clean the outside of the pipe in a circular pattern so the scratches go around the pipe as shown in the video, not length wise as this can provide a path for water to escape, grease the pipe to protect the O-ring and insert to the proper depth with the pipe in line as shown in the video and I've never had a leak when I do these steps, Great video!

@Got2Learn 3 жыл бұрын

Good input, thank you so much!!

@paulmaxwell8851 3 жыл бұрын

Sharkbite O-rings are already greased. Another similar brand, Push & Connect, doesn't grease its O-rings. So I agree: use a bit of grease just to be sure. Your advice on sanding the pipe in a circular pattern is bang on.

@igortak9240 3 ай бұрын

Read a lot about Sharkbites on KZfaq, its pros and cons and decided to replace Accor Lite push -pull valves that started to leak ( internally) after 7 years of use . Followed all the cleaning /square cut as well as checking the insert depth and the 2 clicks that ensures proper Sharkbite Installation. The depth is more key as you may not totally notice the 2 clicks if you push hard /fast enough enough so Depth is more critical than the 2 clicks as basis for proper insert. It's been 2 years so far with no leaks on about a 18 units replacements. I also purposely opened and closed 1 unit 50 times after a year of use and there was no leak unlike the Accor Lite valve I used to have that started to leak even with less than 10 open/closes. The 25 year guarantee on Sharkbite as well as some inputs from plumbing friends who attest they did not have any issue if properly installed made me try this out.

@intrepid5566 3 жыл бұрын

I use shark bite, but never inside a wall! Only where you can easily check them for leaks.

@Got2Learn 3 жыл бұрын

💯

@87thisguy 3 жыл бұрын

That's dumb

@Obshowersyndicate 3 жыл бұрын

Bury them deep

@kristenaasrud533 3 жыл бұрын

In norway its against the law to have it inside walls, unless you want a ugly hatch 😂

@jimb3093 3 жыл бұрын

Weekend warrior here, great vid thanks. Plumbing task complete and didn’t have to call a plumber. Feels good to learn something new and self accomplishment. I enjoyed your soldering copper pipe as well-good stuff.

@Got2Learn 3 жыл бұрын

Thank you 🤗🤗🤗

@texan4life129 2 жыл бұрын

You will call one when that rubber o-ring gives out. It will give out. Then that piece of copper you tied onto will have to be cut because of the corrosion caused to the copper by the water. They are for quick fixes and not permanent.

@jimb3093 2 жыл бұрын

@@texan4life129 good to know, thank you. I’ll keep an eye on it.

@texan4life129 2 жыл бұрын

@@jimb3093 soldering is very easy. I've been a plumber for 20 years and I would recommend this guys video on soldering to learn how. Very good instructor.

@billymorgan7717 3 жыл бұрын

Good information. Although, thus far, sharkbite has not been in my DYI tool kit.

@rexrexford5249 2 жыл бұрын

Excellent,.....this video underscores the steps that need to be taken to ensure the success of Sharkbite connections. Many thanks.

@Got2Learn 2 жыл бұрын

Thank you sooooo much!!!

@unclemarksdiyauto 2 жыл бұрын

Your video was suggested a few times and finally I bit! Glad I watched as lots of good tips that make sense were shared! Thanks again!

@Got2Learn 2 жыл бұрын

Thank you so much man, really appreciate your kind words 🤘🤘🤘

@The_Cyberz 2 жыл бұрын

Great advice. Always clean the tip before inserting and use lube.

@leegray4999 3 жыл бұрын

The depth gauge is also the outside de-burring tool , this stuff works great just as long as you follow the instillation rules to a tee !

@wesg3084 Жыл бұрын

Great tips. I'm getting ready to do a Sharkbite T installation right now. Thanks for the heads up.

@ibrahimwehbe1153 Жыл бұрын

You are really a complete reference for each topic that you tackle 👍

@Got2Learn Жыл бұрын

🙏🙏🙏

@CountryBlessingz 3 жыл бұрын

Thanks I should've watched this before installing angle stop valve with faucet connector. I have a small leak and need to remove stop valve. Great video 👌🏾

@Got2Learn 3 жыл бұрын

Thank you so much!!!

@lorimatthews7240 3 жыл бұрын

Total fail...for me .... leaking...I guess the guy at home Depot should have directed me to debarring...he told me sandpaper...

@AJDIYNetwork 3 жыл бұрын

Excellent presentation! Thank you!

@Got2Learn 3 жыл бұрын

Glad you enjoyed it, please share if you can, it really helps out the channel AJ, thanks!!!

@josecandelario284 Жыл бұрын

Amazing intonation, and presentation, of course! Thanks!

@yeomenim 2 жыл бұрын

plumber here, yeah thats all good stuff, sharkbite are very easy to install, very expensive but makes the project quicker, the depth gauge is a good idea though not necessary if you know where that point is and do all the other things to make a good seal.

@aaronwimbish9382 3 жыл бұрын

Thanks for these tips man i had to learn the hardway first though lol

@Got2Learn 3 жыл бұрын

✌✌✌

@ccfmfg 2 жыл бұрын

The Shark Bite Depth Gauge should be cast in to every fitting so they are always immediately visible available just like strip gauges on electrical Outlet receptacles.

@BritIronRebel 2 жыл бұрын

Amen to that!!

@liman42 2 жыл бұрын

Right. I just today put on a SharkBite shut-off for a kitchen sink. That depth is only half an inch and it wasn't easy to see things inside the cabinet. I thought they make one that "clicks" when it's properly inserted?

@ccfmfg 2 жыл бұрын

@@liman42 I feel you. I don't know if the ones I've used click or if they do it is not always audible with or above ambient sounds or My Radio. What I need to do is get a High Quality LED Rechargable/AA Battery Head Lamp Safety Classes for Dark work places like that. Because My old AA Incandescent Work Headlamp is timing out.

@DemnRaig80 2 жыл бұрын

Nobody uses the strip gauge

@ccfmfg 2 жыл бұрын

@@DemnRaig80 You mean You don't. I can smell your electric work burning now.

@homeroguadarrama7800 2 жыл бұрын

Very interesting points man, they help a lot, keep up the good work you do by teaching!

@Got2Learn 2 жыл бұрын

I appreciate that!!!

@wildcat826 2 жыл бұрын

I love sharkbite valves because they are adjustable and if you have to replace it it's easy to do. No more having to cut pipes and put a new vavle on.

@daypoet23 3 жыл бұрын

I do not know why people hate shark bite. Im a licensed plumber and use them often. Shark bite and pro press. I do not solder. I never had no call back on these fittings. I even shark bite my own water heater and angle stops and home. Never had a problem. The key with shark bite. Make sure the fitting is home!! If not it will leak or blow off. Far as that i use them often behind walls i never had a call back. Most old school plumbers hate shark bite, pro press, any compression fitting. 😂😂😂

@bugattivi7110 3 жыл бұрын

If you a license plumber then I’m super man cut the shit lol

@mikejones5364 3 жыл бұрын

I don't know any licensed plumbers who uses sharkbite or push fittings.

@bugattivi7110 3 жыл бұрын

Mike Jones man telling you once I read his comment bro I’m literally up going to work for a union plumbing shop for the last 4 years and anybody here even say sharkbite it’s a sin in the plumbing trade lol

@bugattivi7110 3 жыл бұрын

Mike Jones we recently ripped out a whole house that was piped out in sharkpipe a fucking nightmare home owner hack job

@daypoet23 3 жыл бұрын

@@bugattivi7110 You said the key word. Owner did it he wasn't a plumber. I would never pipe a whole house using shark bite. I only use it in certain situations. And i am a plumber. Most old school plumbers hate shark bite because they simply do not know how to use it. And pro press machines.

@Thrillhouse114 3 жыл бұрын

Check the inside of your fitting for an anti theft magnet. Bought one from Lowe’s recently and saw it stuck on the inside of the fitting.

@Got2Learn 3 жыл бұрын

😯😯😯

@Gray-Today 2 жыл бұрын

I like this vid. Push-on fittings require greater care with the preparation of the pipe, but in return you get to skip the fire. This vid gets that across.

@Got2Learn 2 жыл бұрын

👌

@HipposaurusRex 2 жыл бұрын

Disagree 100%. You need to take the exact same care with deburring and cleaning the pipe as you would with soldering. It's the exact same process, minus the flux and torch.

@robertevras6577 2 жыл бұрын

Really great tips 👌! Appreciate you sharing!

@lequang2296 3 жыл бұрын

oh, you already answered my question the end of clip Thank you

@Got2Learn 3 жыл бұрын

No problem!

@TheGregoYatzee 3 жыл бұрын

Thank you for the ice pick tip. 😁

@Got2Learn 3 жыл бұрын

Any time 😁

@paulpenland5632 Жыл бұрын

Extremely great and clear tips to using these unique fittings! Thank you!

@Got2Learn Жыл бұрын

😇😇😇

@paull8678 18 күн бұрын

I just used one of these on our water heater. They're all our local hardware store sells anymore. I had no idea they could be reused, thanks!

@Got2Learn 18 күн бұрын

boom!

@jacobcarraway1989 3 жыл бұрын

I know one thing, having a shark bite valve handy when a line breaks and there isn’t a valve accessible is awesome. You will get wet but just push the valve on with it open and close once installed. The only downside is the o-ring could possibly come out but only has one time before. I hope this helps anyone!

@Got2Learn 3 жыл бұрын

Great tip!

@Blessd-savingrace 3 жыл бұрын

THANK U I will pu 1 or 2 God willing i won't need

@time1800 2 жыл бұрын

You can do the same thing with a compression stop

@jacobcarraway1989 2 жыл бұрын

@@time1800 I wouldn’t want anything compression that’s inside a wall or hard to reach location. A compression stop you have to install the nut and ferrule before you even can start to isolate the problem. I do agree with you that it will work though. I have encountered situations non residential when valves aren’t present to add what’s called a “add a valve” this installs on the pipe and cuts a knockout in the line and shuts the water off. Then you can install a sweat valve or pro press valve in place. Another alternative I have used is to use a freeze machine when valves aren’t installed. I have a nice RIDGID pro press tool that’s even better than a shark bite system. This will actually crimp the fitting or valve in place for a permanent fix but cost a few grand for a system of jaw sizes. Also if you ever need to get a shark bite off without the tool just use a crescent wrench and tap it on the plastic with a hammer or channel locks whatever you have. This way you can reuse the fittings or valves after use. I hope any of this information helps anyone.

@time1800 2 жыл бұрын

@@jacobcarraway1989 But your ok with a rubber O'Ring?

@hagensmith9112 Жыл бұрын

I just installed a 3/4 coupling on a pipe from my hot water heater on the hot side and now my hot water isn't running It has an arrow and I figured it was for how the water is running my arrow is pointing upwards and still isn't running anyone able to help?

@MattH-nd9qk 10 ай бұрын

Very informative and quick, thanks for the video!

@bretgreen5314 8 ай бұрын

Thank you for this lesson, and for providing the depth chart.

@Got2Learn 8 ай бұрын

My pleasure!

@brandoncarey2329 2 жыл бұрын

Ok so most of us use common sense. That being said, this is great how to because nobody has any. De- burring every thing is key. Cleaning as well. Waiting toll the pipe is cool also. And love the fact he pointed out how petroleum is not what to use. You will end up with more cracks than a room full of plumbers!

@SOfilmable 3 жыл бұрын

Again, awesome video. Always sad when the video ends. Will you do a dishwasher install video one day ? Asking for a friend ;) - Sam from Montreal

@Got2Learn 3 жыл бұрын

Thank you so much, most probably yes :) From Montreal too !

@akrocuba 2 жыл бұрын

The "ice pick" almost made me fall off my chair...LMFAO!!👍🤣🤣

@Got2Learn 2 жыл бұрын

🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣

@alexbornstein6078 3 жыл бұрын

Chris fix of plumbers

@Got2Learn 3 жыл бұрын

I'll take that as a very nice compliment, thanks Alex!!

@apex007 3 жыл бұрын

@@Got2Learn except you're not afraid to show your face

@Got2Learn 3 жыл бұрын

Hehe ☺

@eddiecedillos8417 3 жыл бұрын

Very informative. Hey can you also make a video on shower valves. Thank you very much

@Got2Learn 3 жыл бұрын

Thank you so much, yes I will.

@LarrySHC Жыл бұрын

Nicely done. Succinct. Good illustrations. And the 7th point is: deburr both outside and inside of the pipe!

@marcn6936 Жыл бұрын

I laughed out loud about the kicking it in.....good video,thanks.

@plove9136 3 жыл бұрын

Thanks for the video, and jokes. Made me laugh, not an easy task, like plumbing.

@Got2Learn 3 жыл бұрын

🤘🤘🤘

@markargenziano4777 2 жыл бұрын

I prefer to sweat joints for both cost and peace of mind but have used sharkbites on many occasions mainly for transitioning from copper to PEX. You'll want to strap the pipes well to eliminate movement of the joint which could cause deflection and distort the o-ring. You can install them on soft copper you just have to hit the end with rounders first and make sure it is straight with no dings or scratches. I always remove the inserts from the fitting first. If using PEX I put the insert in the end of the pipe then push home. Not needed or recommended to use them with copper. When soft copper is cut with tubing cutters there is usually no need for champfering since the cutter leaves a nice bevel but if using on ridgid type M or L i highly recommend not skipping that step because it usually doesnt bevel in nicely like the soft k does. It all comes down to proper application and proper installation. All water mains buried in the ground in the last 50 years rely on rubber gaskets to seal each bell joint. Same principle just smaller scale.

@tareqeghafoor3962 Жыл бұрын

can i copper to pex for a water heater?

@markargenziano4777 Жыл бұрын

@@tareqeghafoor3962 yes shark bites are rated for 200 degrees F just make sure your using the right pex. Pex A, B, and C have different temperature ratings and are meant for different applications

@mauriciopcampos 2 жыл бұрын

Great job man, thank you so much!

@ericmiles6413 2 жыл бұрын

Great explaination!! good for quickies.

@robertweekes5783 2 жыл бұрын

The trick to remove shark teeth - push the disconnect ring in really hard with the orange clip, and *push the pipe in* hard simultaneously. (This should disengage the teeth) Then give the pipe a good tug while holding the clip in

@beentheredonethatoriginals5673 2 жыл бұрын

Use an adjustable wrench, way easier in my opinion.

@fortunatedad7695 3 жыл бұрын

Kicked in the kahoonies haha classic!

@BobMuir100 2 жыл бұрын

Good video, made me aware of a couple of new areas! Thanks Bob England

@Got2Learn 2 жыл бұрын

👌

@user-ct8yt4xy3w 3 жыл бұрын

Great video!!

@iron60bitch62 3 жыл бұрын

Making a test gauge out of a piece of clear flat plastic it’s something I did when I ran into a situation where I didn’t have enough slack in pipe to pull it together or push it apart

@Got2Learn 3 жыл бұрын

Works very well too, thanks IRON!

@tb2324 3 жыл бұрын

I’d love to see a video on this. I’m wondering what do do if you don’t have enough slack to push it together.

@flyingdiscproductions 3 жыл бұрын

the copper I have used was soft for a few years or until we moved them back and forth too much

@brandonbbradley Жыл бұрын

you can look up a guide on how to remove the sharkbite if you put it on and it's leaking (my copper was bent and had to remove). This video helped me a lot, thanks!

@JasonWalkerTN 2 жыл бұрын

Excellent. Perfect information. Thanks for taking the time.

@Got2Learn 2 жыл бұрын

🤘🤘🤘

@Niveous23 2 жыл бұрын

A quick trick for reaming is to use a needle nose and that smooths out the copper. It's not the best option. I always carry my reamer tool, but in a pinch...it'll smooth out burrs.

@ethanweeter2732 2 жыл бұрын

If you are careful on PEX, you can use a utility knife to deburr.

@hartshacks6445 3 жыл бұрын

Biggest mistake is saying reliable and using them as a permanent fix. Should only be used if you do not know how to do a real repair job such as sweating or bruising.It should only be used if you have a plumbing problem that you can fix with this as a temporary fix especially on a holiday when you don’t wanna have to pay extra to have plumbing repair. But when it is feasible have a plumber do it the right way

@rickj1983 2 жыл бұрын

Most new homes now have pex in them. There's nothing wrong with shark bite fittings as long as you know what you're doing. Copper is very pricey in today's world. In very confined spaces it's kind of tough to get a torch to do anything without burning wood. I'd prefer not to use a plumber unless I have to because they do not care what they trash in the process of getting the job done. I do care.

@VFizz 3 жыл бұрын

Excellent recommendations!

@HomeRapidRepair Жыл бұрын

Great Video. Fantastic quick information

@jimbo4203 2 жыл бұрын

Now retired from plumbing, when they first came out, i was like no way is that going to work ! But have used them many times with no issues now

@Got2Learn 2 жыл бұрын

Awesome!!

@smokepeddler 2 жыл бұрын

They all eventually leak. No legit plumber uses them.

@chaetophile 2 жыл бұрын

Sharkbite fittings work on pressurized systems like standard house plumbing, but they will fail if the system is under vacuum. Learned this while trying to draw water up from a cistern using a pump. The vacuum pulls air into the fitting, and the system cannot maintain a prime.

@JeepUSMC 2 жыл бұрын

Does it just suck the o-rings through? I have put them under suction with no issue but maybe it wasn't to the pressure you did?

@llama1917 2 жыл бұрын

Great video and style. Lot of content, no annoying stories.

@Got2Learn 2 жыл бұрын

🤘🤘🤘

@derrickrobertson4715 2 жыл бұрын

Great video - thanks

@sherrimorana4676 3 жыл бұрын

Fantastic job! As always! Best plumber videos on YT 🙌🏻❤️ 1 millions subs + coming soon..😏

@Got2Learn 3 жыл бұрын

Hehe, thanks, hope for 1 million one day :)

@sherrimorana4676 3 жыл бұрын

Got2Learn you WILL get it 🥰💪🏻

@3613jeremy 2 жыл бұрын

The invention of sharkbite is up there with ducktape & Velcro being invented

@stephenfresh1754 2 жыл бұрын

Except shark bites are way more reliable and long-term than duct tape or Velcro no matter what these old men who used to be able to charge an arm and a leg to sweat a copper pipe tell you.. sorry old man it's the new way and it's better than the old way

@MrTiberus1701 2 жыл бұрын

I agree with that assessment except for Velcro. That item was back engineered from an alien civilization.

@jamusmorrison3073 2 жыл бұрын

The oscillating saw or viberation saw.

@spydirty2530 2 жыл бұрын

Duct*

@jackfarrell4727 3 жыл бұрын

Thank you for the tips your videos are very helpful.

@Got2Learn 3 жыл бұрын

You are most welcome, please share if you can, it help s the channel tremendously ✌✌

@CAMPFIRESKY Жыл бұрын

Great video - THANKS !

@Got2Learn Жыл бұрын

Glad you liked it!!

@davidcurious169 3 жыл бұрын

What materials/tools would you recommend to clean old copper pipe to best attach a new sharkbite? In another video you said to never clean the copper, yet on this one you said to always clean the copper!? So which is it? And how best to clean it? And, will it work if it's got some leftover solder (from the older copper connection), or does the old solder also need to be cleaned removed from the copper before using a sharkbite? Thanks! Btw, Love your videos, great content overall!

@Got2Learn 3 жыл бұрын

Yes, it's not suggested by Sharkbite to "sand down" the pipe when installing Sharkbite fittings, however, if there's solder from an existing joint, I would personally suggest to heat up the solder, wipe it off with a rag and then use some light sandpaper or emery cloth to remove the residual solder. But honestly, the best thing to do is to have it clean and untouched, so if you can just cut out that part and deburr it, I would prefer that, cheers!

@awboat 2 жыл бұрын

If it looks like shit, I just use a normal pipe cleaner and make it shiny, just like if I was going to solder it. Haven't had one fail yet?

@ericprobinson 2 жыл бұрын

The shark bite depth gauge has built in reamers so when you mark the depth you can ream it as well.

@bnewman2544 4 ай бұрын

Nice video... and some great humor!

@Got2Learn 2 ай бұрын

Thank you, don't forget to share, it really helps the channel!

@juanbrito-nina2877 2 жыл бұрын

Thanks for this video buddy..really helped avoid mistakes...

@Got2Learn 2 жыл бұрын

🤘🤘🤘

@appleztooranges 3 жыл бұрын

Very detailed. Thank. I did everything but mine looks alittle out of line. It’s been 3 weeks since repair and no leaks. I may just leave it

@3vi10n3 2 жыл бұрын

You’re also supposed to remove the stiffener inside when using it on ridged pipe like copper and cpvc.

@Got2Learn 2 жыл бұрын

Sharkbite says it doesn't matter.

@awboat 2 жыл бұрын

@@Got2Learn But it does constrict the flow. That is one of my main complaints with regular PEX fittings, they restrict the flow. But the Mannings with the rest is better than pipe, but not much better than copper. So the restriction at the fitting diminishes flow downstream.

@cencoast_7.340 2 жыл бұрын

No you’re not. They are specific to Pex and copper. The inner sleeve is actually two different diameters.

@CrzBonKerz21 2 жыл бұрын

Plumbing is the one trade I’ve been least familiar with.. your videos are great!!

@Got2Learn 2 жыл бұрын

🙏🙏🙏

@uBmaniac 3 жыл бұрын

Haha where did you find an ice pick my guy. Made me chuckle

@kamron_thurmond 3 жыл бұрын

An outdoor sporting goods store.

@BInf-cj7du 3 жыл бұрын

Always good to have a small tin of plumber's grease handy. I have caps in the kit for rough in stubouts that have had a good working life. But I always use Sharkbite where access to them is easy. I never bury a push fitting. Just don't trust their life span. Just me.