How to Fix: Rust Bubble Under Paint from a Rock Chip Around WIndshield

Рет қаралды 2,532,276

4 жыл бұрын

This all started with a stone chip in the paint and overtime, the exposed metal rusted and has bubbled beneath the surrounding paint. This is what happens if rock chips are left alone, so cover up chips with touch up paint as soon as you see them.
This chip got really bad and the rust has spread, causing the surrounding paint to bubble. Today I'll strip it down, fill the pitted areas with body filler and prime & paint the repair area to blend in with the original OEM paint on the rest of the roof.
Here's a list of products that I used:
• Wax & Grease Remover: amzn.to/3e36vQr
• Blue shop towels
• Q-tips
• Wire wheel brush set: amzn.to/383G5Kt
• Automotive masking tape (wide): amzn.to/2PkGTE6
• Body filler, hardener: amzn.to/2Oc64Ix
• Mixing board: amzn.to/3qhB1sk
• Spreader: amzn.to/3kLZVyX
• Dura-Block sanding block: amzn.to/3sIbCth
• Sand paper variety pack: amzn.to/2NNsPmr
• Spot putty: amzn.to/3sJh4fA
• Duplicolor self etching primer: amzn.to/308pH7a
• Duplicolor filler primer: amzn.to/3dXe0Iy
• Duplicolor Perfect Match paint
• Duplicolor Lacquer Clear Coat: amzn.to/3qb8cgT
• Tack Cloth: amzn.to/383o52Q
• Orbital buffer 10": amzn.to/303HufA
• Terry cloth pad set 10": amzn.to/3uRvcF8
• Meguiars light cutting compound/polish: amzn.to/3cb6XcT
Since making this video, I have found better Clear coat options:
Spraymax 2k Gloss: amzn.to/43KbyMK
Duplicolor 1K Gloss: amzn.to/3UKXheM
Duplicolor 1K Matte: amzn.to/3A5i6rY
More How-to videos of this 2009 Toyota Camry
How to repair/paint a scratched plastic bumper: • How to Repair & Paint ...
How to paint a replacement fender to match vehicle:
• How to Paint a Vehicle...
How to replace a front fender:
• How To: Remove & Repla...
Leaking transmission fluid from radiator:
• Toyota Camry Transmiss...
How to Replace a radiator:
• How to Replace Radiato...
More Paint & Body videos:
How to: Professional results painting in residential garage: • How to: Spray Automoti...
How to: Prepare plastic bumper for painting: • How to Prep a Used Pla...
How to: Prepare metal body panels for painting: • How to Prep Used Metal...
I don't have Patreon or ask for donations but you can support the channel with some rad gear from my store: 6thgeargarage.com/merchandise/
Follow Us:
Instagram: 6th_gear
6thGearGarage

Пікірлер: 1 300

@tossedsalad5532 4 жыл бұрын

Great video for a simple quick clean up of a spot as you said it is a quick for a simple fix not a masterpiece show car. I'm sure if you wanted you could have put a rust converter over the bare then some self etching primer body filler then the other. But then you would have had to call it more than a simple repair LOL great job Toyota would be proud keeping another great vehicle lasting longer

@6thGearGarage 4 жыл бұрын

Best comment so far. Some people are commenting as if I cut corners on restoring a 69 Camaro. It's just a Toyota Camry with almost a quarter-million miles that I bought for $500. I used rust inhibitor on my nicer vehicle repairs - See my TSX or 85 Toyota vids for that. This Camry is just a cheap daily here in Ohio, where road salt eats vehicles from the underside.

@carlolicuanan719 4 жыл бұрын

6th Gear Garage good work! anyway, i have a question. what is the process if im going to apply some rust converter after the bare metal? im just confuse of what is next to apply after treating the rust with rust converter. thankyou

@6thGearGarage 4 жыл бұрын

@@carlolicuanan719 I would follow the instructions of the specific product you use., as there are different types of converters. Some you can prime over, and continue the body work.

@matthewfarrell317 4 жыл бұрын

@@6thGearGarage As a Camry person with a modified Camry, it's not just a Camry :p lol, also would prefer my Camry over the Camaro. That said, a good quick repair doesn't need to be perfect, just enough to stop the rust from growing.

@6thGearGarage 4 жыл бұрын

@@matthewfarrell317 Thanks, I agree. With the high miles and being an ohio car that sees road salt, a spot returning above the windshield is the least of my worries. Around here cars rot underneath faster than they rust on the surface. I'm happy to make the exterior look better and get a few more years out of it.

@mickholgate3347 4 жыл бұрын

Hi Mate, a few improvements that will assist you and your viewers. Once you have sanded all the flaky rust away, always use a rust converter to neutralize the active rust before putting filler over the top as it will de-laminate in a few years otherwise. Something like phosphoric acid will work perfectly and is cheap. Once you use wax and grease remover/ prepsol, don't touch with bare hands (like you did before etch primer) as this will transfer grease from your fingers and hands and could cause 'fish eyes' in your paint.

@6thGearGarage 4 жыл бұрын

Thank you for the advice!

@olitonottero7620 11 ай бұрын

very helpful thanks

@Sceme1991 9 ай бұрын

I have never figured out what you're supposed to do with phosphoric acid after it has done its job. Do I just leave it there or am I supposed to wipe it off and if yes then with what?

@PalpatinesPlumber 9 ай бұрын

@@Sceme1991 Just wash it off with warm water, that's at least what was recommended in the bottle I used.

@ratgreen 8 ай бұрын

Yeh wash it off with water after its been on for 30 mins or so, or as long as possible before it dries, (otherwise it'll dry with phosphoric acid crystals on it, which will eat away at the metal if left there long term because its acidic.) Then dry with hot air asap, then paint asap after that.@@Sceme1991

@matthewchandler2647 2 жыл бұрын

Minor rust repair & painting just got a whole lot less intimidating, thank you!

@cynthiafougere8404 2 жыл бұрын

Thanks my friend. It takes guys like you to encourage guys like me who don’t have a bunch of confidence or know how to see even a small job through. Looking forward to seeing more of your videos. From Nova Scotia, Lester

@kamilk6956 2 жыл бұрын

I've watched this video like 10 times already while fixing up my project car. Great video tutorial, thank you for putting this together.

@marilynvanos3081 4 жыл бұрын

The '89 Toyota is rusting like crazy and I can't afford a body shop. This is a great vid! Nothing but the facts. No crazy lead-in chat, no music, just good instructions and visual details! Mahalo!

@brayden6260 4 жыл бұрын

That was an outstanding, clean, and to the point video.

@Stu650Zuk 4 жыл бұрын

Thank you for your helpful DIY tips. I've got over a decade of professional certified hand spraying under my belt for airplanes. Tips like these on a used daily driver and to have it coming out looking good for not a lot of money is what I look for. Sure beats touch up paint in a tube..lol! I have several cars/trucks and both foreign and domestic. I always liked my VW's for a fun, sporty, daily driver. I own 2 as of now. My nicest one is one I searched for. It is a 2009 Jetta GLI 2.0 turbo manual shift in top condition. My second is a 2010 Jetta SEL 2.5 with a DCT trans and every option you can think of. I found it down south needing work, but in great overall condition. Just some normal scratches and a small rust bubble on each fender. It had average miles of just over 90K, but the owners neglected oil changes, and probably the right oil for that matter. The inside of the engine was filthy and it was out of time from a stretched timing chain. I made a deal with them and trailered it home to fix back up as a DD. If the interior wasn't like brand new and being the top of the line SEL package I would of passed on it. Not to mention the body was in very good shape for the year. I decided to source a used engine instead because of the gunky build up in the engine from negligence. I found a matching 25,000 mile engine in clean like new condition for $700..Wished I could find a 2.0 Turbo for that kind of money. Well anyway I decided to get the matching DCT that came with that engine as well for an additional $500. All said and done I have under 3K total in the car and it looks, drives, and runs like a brand new car. If you have the know how and take your time you can save a lot of cash. Plus they are a nice car too. Man I was surprised as how strong that inline NA 5 cylinder turned out to be. I let my son drive it and drag race my GLI at the local track in the 1/4 mile..He actually pulled me through the 1/8th and I barely ran him down at the 1/4...I was impressed for just a daily driver that also looks cool and handles and drives great. Well worth the $3k and my time...sorry for the book..its videos like yours that help us diy'ers the most. thanks.

@T_Shane 3 жыл бұрын

Very helpful. Got a few rust bubbles on my f150 which is 14 years old so I’m not wanting to pay someone to fix something so simple. I’ll most likely be giving this a try this weekend. Thank you for the help.

@ncognitod.460 4 жыл бұрын

I have a rust bubble like yours on my hood. This was a truly excellent tutorial. I learned more in just the first 3 minutes (yes, I checked!) than I did watching several other videos on here. I now have the confidence & knowledge to tackle my hood. I can't emphasize enough how much this has helped! Might even make a video when I repair it in the spring. Thank You!

@HavokBWR 2 жыл бұрын

how did your repair go?

@lukeellis8507 2 жыл бұрын

@@HavokBWR he died :(

@amj76425 2 жыл бұрын

The Gospel is 1 Corinthians 15:1-4 kzfaq.info/get/bejne/osiSZ9uovtCVaZs.html How to get saved

@jasonchristopher2977 2 жыл бұрын

@@lukeellis8507 Dam rust kills us all!!

@lukeellis8507 2 жыл бұрын

@@jasonchristopher2977 so true. may he rest in peace. im also taking the journey to repair my rust spots on my hood and other things

@kieranstephenson3187 Жыл бұрын

Great video! This kind of thing always amazes me after everything is done, and how close you can get to making it look good with comparatively minimal effort and cost!

@OldeCarrGuy 4 жыл бұрын

Great demo! I think you made it look easy to novice DIY'ers. We frequently do these types of touch ups on some of our cheaper cars!

@kevvyg04 3 жыл бұрын

100% agreement!! - I never buy a new car. The one I have now cost me £450 and is still going 3 years on ..,,👍🏻

@AlexanderKubik1993 2 жыл бұрын

I’d never ever take my car to you. You guys are horrible at what you do

@bensettle194 4 жыл бұрын

One of the better videos I have watched. Very well presented.

@darrelldavidson1987 4 жыл бұрын

This was an very informative and well executed video! Nice work! Thanks!

@averagejoe9011 3 жыл бұрын

Great job! Bought a 2013 Sierra. Has this problem on the roof as well. I was going to spend $1000 to have a shop repair it but you convinced me to do it. Thanks for sharing. You saved me and my family a ton of cash!

@6thGearGarage 3 жыл бұрын

Glad it helped

@N8TheSnake Жыл бұрын

Bro this video is gold, so clearly explained and not over my head. Thank you!

@kenlaw04 2 жыл бұрын

This turned it out really well. Great video! Exactly what I needed to watch for my next project!

@Peter_Riis_DK 2 жыл бұрын

Amateurs tip: Wet the floor down when painting to reduce dust contamination.

@megaruhe6296 2 жыл бұрын

@Max advice for you...let amateurs do the work themselves if they want.

@asmongoldsmouth9839 Жыл бұрын

@Max When you own a $10,000 car you don't want a $10,000 paint job friend. 🤣 No one can afford professional body shops. If it wasn't for insurance companies you guys wouldn't have a job.

@destineecostanzo2603 Жыл бұрын

Your a Genius . Thanks !

@pranavdutia Жыл бұрын

Parked in building basement which gets one cleaning each year. This tip is useful for me. Thanks Peter.

@RobinWhistles Жыл бұрын

@Max advice for advisors....let the humble amateurs throw in the toupence worth 🤷‍♂️

@AVB2 4 жыл бұрын

An excellent video. To the point, clear concise directions, no goofy music in the background and showing exactly what you did. As a side note if you don't have a buffer or polisher try elbow grease; it works quite well!

@DigitalConfusion Жыл бұрын

Gorgeous job sir. Really shows how taking the time to make sure each step is done flawless is worth it.

@6thGearGarage Жыл бұрын

Thank you very much!

@chriskitchen3913 Жыл бұрын

I really like how this video simplifies something that can be very intimidating

@JoeSmith-pf7ir 4 жыл бұрын

For what it is I would say thats pretty well done.

@Robert8455 3 жыл бұрын

Nice fix! I like that Q-Tip idea too.

@gsc8902 3 жыл бұрын

Thank you for this video, just bought a cheap car which needs a few spots doing and this video was clear and concise!

@krassimirpetrov7131 2 жыл бұрын

One of the best dupli color jobs I’ve seen !

@peterjensen3162 4 жыл бұрын

Great looking 👍🏻 thanks for sharing this and merry Christmas 🎄

@msk3905 3 жыл бұрын

I have this same thing happening on my car, going to try the same repair and hope it blends in as well as yours

@leihooeh Жыл бұрын

Great DIY video. Best one I've seen so far. Thank you for the content! Well done.

@guidosarducci3047 4 жыл бұрын

Nicely done. A real confidence builder.

@michaelvincentvillamer2188 4 жыл бұрын

Very helpful. Noticed some rust in my mitsubishi lancer. Will DIY soon. Watching from the Philippines. Subscribed. 🙂

@victorloera3415 3 жыл бұрын

Evo?

@PaddleDogC5 4 жыл бұрын

If brown was still there in pits that means you left rust. It will be back again. Use rust converter at bare minimum, then epoxy paint. Then fill it. Then paint it.

@dharm3974 3 жыл бұрын

Does filler adhere to rust converter better than bare metal?

@mikebennett938 3 жыл бұрын

@@dharm3974 I'm not an expert but I have placed filler over rust converter after a light sand. No issues to date. I do see a lot of debate around the whether you should prime before you fill, or fill before you prime. All experts, all different opinions. I typically prime first just to be sure but I wouldn't like to say that its the only way. I 100% agree with PaddleDodC5 though, there is certainly a risk of recurring rust. Doing 'something' is better than having to do it again.

@dharm3974 3 жыл бұрын

@@mikebennett938 Thanks for the advice, man. I'm new to body/paint work of any kind so trying to figure it out. But I agree, seems like if you're going to go through all the work of repairing it you may as well do it as good as possible.

@mikebennett938 3 жыл бұрын

@@dharm3974 I'm reasonably new to it as well, although I am getting more confident. I can pull out dents, apply filler properly and paint. I've painted whole cars. I've even custom made whole panels and welded them in. It's fun :). The only real advice I can give is practice, practice, practice! Start small and examine your mistakes, then try again. It's ok to not be perfect, I'm certainly not. I think there is one professional who says it really well on youtube, it's only paint! if you get it wrong, sand it off, try again. If you can afford it and have the space, go and buy the biggest piece of crap you can find and practice on it. Hopefuly it's a piece of crap you can enjoy long term though. Happy tinkering :)

@mikebennett938 3 жыл бұрын

@@dharm3974 I just found this, finally someone who actually shows why primer needs to go first and what will happen if you don't: kzfaq.info/get/bejne/oc10hbOWsp2zkqs.html

@robmcgahey2305 8 ай бұрын

Really nice video! Love that you really highlighted the steps. Thanks

@powerofknowledge7771 3 жыл бұрын

Finally, someone who did this THE RIGHT WAY!! Everyone else misses the clear coat step, and instead, they just use wax... My question to them is , what do you do when the wax wears off? They also didn't feather it in like you did. The difference is like night and day!

@markt9438 4 жыл бұрын

Simple good straight forward ! Thx

@buggsy64 4 жыл бұрын

looks awesome good job!

@lejeuneceramiccoating4829 3 жыл бұрын

GREAT video man, very detailed. Exactly what I was looking for.

@Mondo5000 5 ай бұрын

Thanks for the video! Repaired a rust spot using your detailed method. Worked out amazing!

@ehh2681 2 жыл бұрын

After applying the body filler I wouldn’t go back with a 80 grit. I’d just hit it with a 150 grit and bring it down smooth, then spot filler. Then 500 grit, followed by 800 or 1000 grit.

@theirishman088 4 жыл бұрын

Good video for a 500 car. Try using clear blender to blend in the edges of the clear coat. It comes in a can also. It won't leave an edge of the new clear on old paint. Nice job

@rich123189a 2 жыл бұрын

Exactly! I was thinking the same thing

@cosmin1518 2 жыл бұрын

I will definitely follow your instructions when i start doing some work on my rust bucket passat 😁

@Brett_is_Veng 2 жыл бұрын

amazing job, nicely done. Making a $500 car look like a much more expensive one is awesome and a great way to prolong the life of a vehicle.

@williamdastous-stampe2865 4 жыл бұрын

Thanks for the great video! Would you recommend applying a second coat of self-etching primer before moving on to the filler primer?

@6thGearGarage 4 жыл бұрын

Yes you can apply a second coat if the first coat did not completely cover.

@340rps 4 жыл бұрын

You should wait a few weeks before waxing. The paint needs that time to fully "cure". You dont want to seal the paint to soon as it needs to breathe until hard. Not a bad for a quick repair though. One good trick to get a level finish is to make the first primer coat very light, sand very lightly with a block sander. The low spots will show the primer. Thin coat of spot putty over those low areas, sand smooth. Thin primer coat and light block sand. ect.

@Rough-inevitable 4 жыл бұрын

Great thorough instructions! Subscribed cant wait to see what your channel offers

@goldwolf0606 4 жыл бұрын

I did this kinda work on my Tercel when I was a kid. The Tercel had too much rust for me to want to complete the whole body. What I did do, I didn’t use clear coat and it looked pretty nice. I didn’t protect the plastic or the glass... learned that the hard way 😂 fun times. Now I take meticulous care of my car and don’t let it start rusting Or having mechanical problems.

@aurelienyonrac 3 жыл бұрын

That was a really helpful video. Thank you for the list of tools.

@MikeGervasi 4 жыл бұрын

I just had my Body Shop do this same repair. They couldn't get the windshield edge without removing the glass so we are gonna do that next and just replace it.

@av8ionUSMC Жыл бұрын

Finally, a solid solution and not a hack. Thank you.

@beagles70 4 жыл бұрын

Very good job. I didnt go deep enough to the metal on my 2000 Ford Taurus as my rust bubbles have sadly returned in less than a year. my problem area is right below the gas cap- a 6inch square. I'll use this video for my next try and the wire brush attachment.

@epr1 3 жыл бұрын

Geez I can’t believe you did that in your garage. That was incredible

@6thGearGarage 3 жыл бұрын

Thanks!

@c4279 2 жыл бұрын

If you're going to use body filler to make the repaired area smooth you may as well remove those blackened areas - because that is where the rust will come back from. I'd use a Dremel to drill out the blackened areas and sneak in some epoxy and fibre-glass underneath the area to give a string surface for the filler to bond to. I've done the type of repair shown in this video and the rust always starts to re-bubble after 12 months.

@evictioncarpentry2628 2 жыл бұрын

No need for that. Just use a rust inhibitor like POR15 on it.

@chrisgraham2904 Жыл бұрын

Agreed. Rust is automotive cancer. If you leave anything behind, it's going to grow and create the same damage within a year or a little more. The Dremel tool gives you the same ability and precision of a dentist's drill to remove all visible spots of oxidation (just as the dentist treats a cavity). Apply two coats of a rust converter to treat the specs of oxidation which may not even be visible to the naked eye and allow the converter to convert for at least 24 hours before proceeding to filler. I repaired three similar rust spots in 2004 on my 1999 GMC Safari van and they have never reappeared.

@goranolsson5981 Жыл бұрын

in sweden we do spot blasting only took 5 minutes then the rust will not come back

@kenmastersmaster Жыл бұрын

@@chrisgraham2904what rust converter do you use for car metal?

@kenmastersmaster Жыл бұрын

@@chrisgraham2904 wouldn't etch primer also prevent rust from coming back?

@dreamingcode 3 жыл бұрын

Really nice repair I'm going to do this on my old 1969 Impala which is in good shape except for some Rust spots

@josechavez5950 4 жыл бұрын

Super video, thanks for being so helpful and thorough!

@rotorblade9508 4 жыл бұрын

What about a 2k primer before the body filler? Also if there is rust underneath the sheet it needs to be removed and treated as well

@lagunafishing 2 жыл бұрын

You can use a Dremel tool to remove the rust on small areas and apply a rust converter to pitted areas before priming and adding filler. Always apply your primer both before and after adding any filler. Also if the surface is smooth without any pitting or bare metal exposed you can usually paint over the converted rust directly.

@mehmeh5471 2 жыл бұрын

Filler should generally be applied to bare metal

@darkwood777 2 жыл бұрын

@@mehmeh5471 Filling over primer is OK. Filling over paint is a no-no.

@nigelnightmare4160 Жыл бұрын

While you CAN paint directly over converted rust/bare metal, it is better to etch prime it first.

@jwsclark19 4 жыл бұрын

Very helpful, thanks! This also happens to be the exact paint I need for my Corolla.

@VinylToVideo 4 жыл бұрын

I got a better idea.. fill the inside with fuel and throw a match in. It will look better after.

@VinylToVideo 4 жыл бұрын

@@aydentheninja877 Clearly you've done that already if you own a Toyota Corolla as you'd have no brains.

@shannonshawartworks1430 4 жыл бұрын

Thank you. I'm try this on the weekend for my vehicle.

@bierechaude6387 4 жыл бұрын

Nice job !

@fb3824 4 жыл бұрын

This was an excellent quality repair. Quality means adherence to specification, so while it may not be a top spec repair, it was well executed to meet that spec.

@Dragandspinn 3 жыл бұрын

Awwww Budd! Super impressive! Seriously. I have the same issue on a quarter panel. Im going for it . You've erased my paint match questions.

@KASLtja 4 жыл бұрын

Thank God for KZfaq! Awesome vid.

@shaktichauhan3744 4 жыл бұрын

Looks perfect. I need to do the same for my Jeep TJ which has several rust spots bubbles

@Blazingangels0 3 жыл бұрын

Yo facts same with my TJ

@germaned.lealnino631 3 жыл бұрын

Yep, a few

@DanielOlma 3 жыл бұрын

On top of my driver side fender. I think it might be a design flaw.

@grantsaunders6177 4 жыл бұрын

A detail oriented DIY video that didn't make me cringe. Thank you.

@timothyoneal8351 4 жыл бұрын

Great video, going to do mine now. Thank you!

@georgedavidla 3 жыл бұрын

What a great job! Thanks for all this amazing info you've shared.

@6thGearGarage 3 жыл бұрын

Thanks for watching!

@Bigcrappie1208 4 жыл бұрын

I always s love reading all the Monday morning quarterbacking on these types of repairs. This guy done a good job on an inexpensive car. Get over it people!

@chris-thumper7205 4 жыл бұрын

But all that work only produced mediocre results. Better to do the right way, it'll only come back and this what we get when we buy used cars at used car dealers. Quick, unreliable, and temp fixes that look good at the dealership, but once you get them home.... 1 month later you have the same issue.

@gravedanger789 3 жыл бұрын

Very good video. Biggest mistake i make is in the spraying. Definately light dusting with the spray can is way to go. takes longer and time consuming waiting for the drying but the results are a waste of time spraying to heavily. Lots of light coats is best. Lighter and more often the better.

@6thGearGarage 3 жыл бұрын

100% It's easy to go too heavy on the coats.

@robertstone8852 2 жыл бұрын

good video, enjoyed the informative step by step instructions, the different materials you used and the final result! Painting an entire car is a lot of work and requires lot of skill and patience, especially if there is rust, old body work, etc!

@6thGearGarage 2 жыл бұрын

Glad you enjoyed it!

@ytsux9259 2 жыл бұрын

@@6thGearGarage Why did you use all those coupons for coverage? 😭 I use similar coupons to purchase on a regular basis.

@6thGearGarage 2 жыл бұрын

@@ytsux9259 Sometimes you gotta work with what you have on hand... had to pick between cheap food or a nice car haha

@petebutler5139 3 жыл бұрын

I really enjoyed that video! I am a DIYer and it just popped up in my feed. But guess what? Now I’m a subscriber!

@olivertaylor4779 4 жыл бұрын

Great video but you should have used rust converter before the filler, and when you have finished painting you need to leave it at least 4 weeks before applying any waxes or sealants to let the paint 'gas out'.

@EazyDuz18 Жыл бұрын

snake oil, doesnt work

@jessicabriltz2261 Жыл бұрын

@@EazyDuz18 what is snake oil?

@speedokoterefinishnetwork4937 4 жыл бұрын

Even tho alot of the processes were not done to auto body industry standards , I'm very suprised by your outcome and kinda impressed. Nice.

@alexwmello 3 ай бұрын

I never had seen a video like this before! Professional level! Thanks for share! Now, you have more a brazilian follower!

@wazzlopiok240 3 жыл бұрын

Thanks man! Saves me taking my almost dead car in yet again! I had the opposite problem, I could only move forward. I had to do some yoga pose just to sit in the car!

@EasterlyArt 2 жыл бұрын

Really appreciate you sharing this. I currently have this issue on my car in a number of spots. I was quoted $1,500 for repairs and needless to say the idea of just slapping a glob of sealing glue or the like felt like a cheap alternative. Though I knew I wanted something that would actually fix my car, not just be a "duct tape" fix. This is exactly what I needed to see so I can feel confident to fix my car on my own... or convince my friend who actually works on cars to try something new. Out of curiosity, if you had to ball park the cost of your tools and supplies for this job, where would you hit at? Seeing if I can save up money to budget for this. I assume it will be less than $1,500.

@6thGearGarage 2 жыл бұрын

I would guess maybe $100 for materials. I have links to the products used in the description if you wanted to price them out. It's absolutely worth trying it yourself!

@Gripen85 3 жыл бұрын

Pretty good deal, 3$ for 10 nuggets and a large french fries. Thanks for the video ;)

@Raumyn Жыл бұрын

Excellent job and tutorial! Thanks for this vid, basically exactly what I need to fix on my Jeep.

@waqasmuhammad7264 4 жыл бұрын

Nice job and thanks for given knowledge

@gavinrichardson3918 4 жыл бұрын

Good tutorial however would it be worth adding a rust cure solution before filler to prevent tiniest rust spot returning?

@6thGearGarage 4 жыл бұрын

Yes. On a nicer vehicle with lower miles, it would be worth it.

@turboflush 4 жыл бұрын

Chris fix 2.0 Lol Looks good dude

@joshuaman01 4 жыл бұрын

Hey guys 6th gear garage here!

@6thGearGarage 4 жыл бұрын

Funny because one time I said "Hey Guys..." in an intro and later realized it sounded like a Chris Fix vid. He's the diy master, love his vids!

@cal88usa Жыл бұрын

Very nice job, thank you for posting. My daily driver, has 3 big rust spots on the trunk.

@mattywollaston3996 4 жыл бұрын

Fantastic job mate, love ya work!!!!!!

@j.j.springer1099 4 жыл бұрын

You didn't throw those nugget coupons out, did you?

@y_uwannaknowmynamehuh741 3 жыл бұрын

lo!!!

@StrongFreeLovin 3 жыл бұрын

most american comment you can find in this comment section

@user-hz9mw2gt8b 4 жыл бұрын

Thank you 10k times being disabled I can't afford the "professional" job, but you made me confident I can do it myself. Love.

@Hallsurfer2U 2 жыл бұрын

Great video with good photography and instruction. Cheers !

@RaisingAwesome 3 жыл бұрын

Great work. Turned out great. Thanks for sharing!

@helivesonforever 4 жыл бұрын

Great DIY video, BUT, I can almost guarantee you that the rust is starting from the seam underneath the windshield urethane, rock chips never bubble up like that unless they're 10-20 years old. Once the rust eats enough of the metal under the urethane, you'll get a leaky windshield in the rain and that will cause major floor pan rust. This is all caused by poor windshield installation and the installer not using a primer before they lay the bead of urethane. I totally get that it's a cheap car but just keep that in mind for future reference, or if anyone else is attempting to do this they should note that it's not a permanent repair. It's about $100 to have your windshield removed, many glass companies will come to your house and do it, and you can follow the same steps in this video for fixing any rust under there MINUS the body filler, just remove the rust and leave the metal pitted, the urethane takes the shape of the metal so any imperfections are okay to leave. Then body fill any necessary areas ASIDE from the seam, primer and paint the entire repair area and have the windshield PROPERLY installed again.

@6thGearGarage 4 жыл бұрын

Thanks for the advice!

@bentnickel7487 4 жыл бұрын

Classified When you spend $5000. for one you worry about crap like that, but when you spend five hundred you don't worry about anything. Not questioning you, but insurance cost more than the car's worth. That's how you live way under budget and don't sweat the little shit. If it doesn't purr like you want, fk it, just call the junk yard and look for another $500. ride. :-D

@helivesonforever 4 жыл бұрын

Bent Nickel I get that, but people will be doing this on nice vehicles thinking they’re doing a good job. It’s important that they know it is not a permanent fix, not really a fix at all. Kind of like slapping a fender flare over a rusted wheel well. Might as well fix it properly before you’ve got rust holes if you plan on keeping the vehicle. For the work involved, having the glass pulled isn’t anything more than $100 on your part, you won’t even be doing the work and you can fix it right that way.

@jasonchristopher2977 2 жыл бұрын

The major issue with this is when you showed the pit u said to use spot putty, to the left is rust. The dark black/brown is rust. Wire brush won't get rid of it all. Only sand blasting or use a rust reformer or acid. You can do all the nice work and paint but not worth the time and money when rust bleeds through in 3 months. I use Ospho. I know this because I did this when I was a young man restoring a 72 VW Bug. I did same as you and it rusted through in 6 months. Then a girl filling with gas day after I repainted, pump didnt kick off and my new paint job bubbled from the gas. So 3rd times was a charm. I learned from a grumpy old man that if you do a great job on prep you can paint with a spray cans and still look good! Gotta get rid of all that rust. Even if you don't see it, rust will be at the bottom of those tiny pits. If it was there it will be there until you use sand, acid etc Use whatever you want but use it and have it 100% rust free. Other than that it was a good video. I'm not breaking your balls I just want your work to hold up and be as good as it can. Even a newbie if following all the steps can get any job dam near perfect. We're judged by our work. And we all make mistakes.

@6thGearGarage 2 жыл бұрын

Thank you for the advice!

@Life2018Z 4 жыл бұрын

Nice work, thanks for sharing.

@RiSkyNick 24 күн бұрын

So helpful thx! Bought a budget car with a gnarly rust spot on the roof. I'm gonna use this advice!

@irietropicals4255 Жыл бұрын

Pro tip. Always apply an anti corrosive application to bare metal before applying any filler.

@kenmastersmaster Жыл бұрын

Filler can go directly on bare metal

@ScandiSledder8000 Жыл бұрын

Tought filler could go strait on metal?

@sergioavegazavala5116 8 ай бұрын

@@ScandiSledder8000 if there are any pits, rust will come back. I sanded the edges of a metal door last december, used some filler on the pits and bumps and applied 2 coats of anticorrosive primer, and 2 of color (no clear since it was a door). it is now september and rust came back in the same areas. This time will try some metal conditioner. some primer and then the filler.

@brianvilmer3926 4 жыл бұрын

Dude! You wasted a Burger King coupon! Haha! Nice video, thank you!

@wheresmygrasses1549 2 жыл бұрын

Thanks! I’m gonna really need that since my Uncle gave me his Acura RSX. He wasn’t very good at taking care of the car.

@chriswood4510 Жыл бұрын

Best DIY paint video. I love they way you didn’t mask the entire car lol seems more reasonable than some other videos

@6thGearGarage Жыл бұрын

Yeah it's really not needed with lacquer aerosol paint. its overspray turns into dust and doesn't stick to everything like a urethane paint does.

@Unrealdruiddd 3 жыл бұрын

I just did 20 spots just like this on my Subaru 2011 Impreza.... Took 3 days total...

@sindrek9779 3 жыл бұрын

How is it holding up?

@faridmk3707 4 жыл бұрын

What I dont get is why people dont treat the metal before covering it with filler. I found a rust inhibitor liquid that I spray on the exposed metal and then proceed to fill it up. No bubbles come back, ever.

@V8madm8 3 жыл бұрын

This! Every video on YT...they put filler on exposed metal. In one year rust will be back.

@The85F0X 3 ай бұрын

That’s amazing. For a few rattle cans, that is a great job. I’m about to fix some spots I just found on my 17 tundra and haven’t done body work or paint in 20 years. I didn’t know there were spray cans of match paint. Thank you.

@6thGearGarage 3 ай бұрын

You can get them at most parts stores, or I've even seen them on ebay/amazon.