▼EXPAND FOR TOOL LINKS and INFO▼ Watch Next = Harbor Freight vs other Parallel Clamps - kzfaq.info/get/bejne/oKdkocuYvpmUm4k.html Tools In This Video: Current Harbor Freight Deals - sovrn.co/pnvc06d Bremen Parallel Clamp - sovrn.co/1gzlppz Pittsburgh Bar Clamp - sovrn.co/isu3emi Hand Screw Clamps - sovrn.co/kz808c4 F Clamps - sovrn.co/1kmjj26 Magnetic Trays - sovrn.co/nopmixp Tool Wall I have - amzn.to/3H1ySwJ Magnetic Hooks -- sovrn.co/5ctsjh7 Magnetic Tool Holder - sovrn.co/10feg7o Magnetic Paper Towel Holder - sovrn.co/121b1rh Hercules Miter Saw - sovrn.co/tvwe222 Bauer Planer - sovrn.co/1etpcno Tool Wall I have - amzn.to/3H1ySwJ BETTER CHOICES THAN HARBOR FREIGHT Irwin F-Clamps - amzn.to/3FdWJrB Bench Mark Rules - lddy.no/1e3bc FastCap Tape Measure - amzn.to/3AX74pg Swanson Square Combo Pack - amzn.to/3Vz8hLs Bosch Router I Recommend - amzn.to/3VikTqA Narex Chisels - lddy.no/1e3bf DeWALT Table Saw - amzn.to/3Vz1xx2 Whiteside Router Bit Set I Recommend - amzn.to/3VxbStK (If you use one of these Amazon and other affiliate links, I may receive a commission) Some other useful links: Daily Tool Deals on my website: www.731woodworks.com/tool-deals Subscribe to our email Newsletter: mailchi.mp/7e44c16eefdc/731-woodworks-email-newsletter Check out our easy-to-follow woodworking plans: www.731woodworks.com/store Outlaw's Board Butter - So Good it Should be Outlawed: www.731woodworks.com/store/boardbutter
@FixItFrench Жыл бұрын
I own the Hercules Table saw and they remodeled it in the last year or so. I have the original and it has a rack and pinion fence. The only negative about the saw I have found is that you can’t use dado blades on them
@fromthebackofmymind Жыл бұрын
Thanks for this video. FYI, about eight years ago I found a list of countries that china exports to. There were about 135+ countries that received A rated trade goods. The sole country receiving -B trade goods was Guess who? It is about hate. And it is about the steel. HF steel is sub grade. The best chinese steel goes into their growing fleet of aircraft carriers, missile cruisers, destroyers and submarines. Artillery and tanks. They are a globally focused communist country. Working on a 100 year plan towards economic and military domination. We still butter their bread. Only for a few more years.
@fromthebackofmymind Жыл бұрын
@@FixItFrench Thats a big no go then.
@markthompsoncpa Жыл бұрын
I'm not saying the BBB is a bit of a scam bit..................
@Daveyk0212 ай бұрын
I love Harbor Freight, but I am not using most of the tools professionally. The have a new screw drive kit that I am. I also like their 6 piece small screw driver kit.
@davidtadlock2238 Жыл бұрын
My cousin was a mechanic for about 5 years prior to becoming a Paramedic, and his tool kit primarily consisted of Harbor Freight hand tools. He definitely didn’t think they were superior to top tier brand names, but they overall performed awesomely and he had like 1/10th of the cost in tools that some of his co-workers did. A lot of them were in significant debt to snap-on and others. He actually gave his whole tool kit to a new young mechanic that didn’t have any when he left to be a paramedic.
@bravofighter Жыл бұрын
Yeah, the Snap-On truck should be thrown out of every garage they darken the doorstep of. My buddy has a huge tool chest full of their tools, but lives in a rented cottage because half of his paycheck goes to Snap-On. They charged him $150 for a single racket…NOT A SET, but a single ratchet. I wanted to weep for him, but he still thinks they worth every penny….it’s like he’s been brainwashed, nothing can sway him. He swears up and down that anything else is trash.
@benjinmins Жыл бұрын
W cousin
@donwilloughby2667 Жыл бұрын
Warranty sucks on name brands give you a hassle for weeks when you need it right then. Where harbor freight for a extra couple dollar give you extra warranty they replace it in the store.
@GoneNForgotten Жыл бұрын
@@bravofighter ive noticed that too, i think people get caught up in trying to impress everyone, with snap on it costs alot and alot of people in the mechanic world are man babies and will make fun of you if you dont have it, personally myself i dont care what anyone has, as long as it gets the job done, i carry all my main hand tools in a case i found at the thrift store and carry my harbor freight power tools in the bags they come with, and guess what? I dont think twice about it lol
@treatzfortruckerz3913 Жыл бұрын
I am a big fan of snap on tools they are expensive certain snap on tools did a much better job. I found The screwdrivers wrenches and impact drivers are the best buy such things as breaker bars, sheet rock knifes wear a waste of money. Extensions as well . Buy what you can afford.
@joehanika Жыл бұрын
I love when people with a following bring to light that cheap items have their purpose! I love me some harbor freight. There is a time and a place for everything.
@ancienttom97 Жыл бұрын
If you're like me as you continue to shop there, you will begin to notice that they're systematically making changes to their product lines to elevate the quality of their products.
@Kasper623 Жыл бұрын
@@ancienttom97 this is so true
@a9ball1 Жыл бұрын
Harbor freight is great for a one time use and abuse type of situation. Don't let your chisel hit a nail, naw it's harbor freight just whack it harder. I've also used dollar store tools. For example, a long nose pliers might not be worth anything but if it's just for holding something while soldering it then they work great.
@joehanika Жыл бұрын
@@ancienttom97 I have seen that! it is great to see.
@jdarokhajiit9153 Жыл бұрын
There is not a lot i will swear by at harbor freight but for one offs and disposables harbor freight is boss
@GangstarComputerGod Жыл бұрын
As a weekend DIYer, I don’t need heavy duty use. However, I’ve inherited a ton of my dads stuff. Now that I’m looking to buy some things I’ve finally started looking at Harbor Freight. Glad to hear it’s not as bad as the rumors claim.
@robertcraigh73 Жыл бұрын
The router bits can be useful because you can buy so many different styles at a much cheaper price. Gives you time to figure out which bits that you're going to use the most and upgrade later instead of buying the most expensive bit kit possible and finding out that you only used two bits. I like a lot of things about harbor freight in that regard of being able to actually test out a type of tool to see if it's useful to your workflow.
@chrisfarley66627 ай бұрын
I've done that, buy a cheap tool at HF and then realize I love or hate it. I didn't realize how much I would use a grinder tool till I bought a ten dollar one at HF. I then spent the money to get a much more expensive Dewalt after the HF tool quickly burned out.
@aerialrescuesolutions32776 ай бұрын
Well said.
@jayduncan89946 ай бұрын
I'm a fan of this approach. Get a cheap kit that has everything you need. As pieces break or wear out, it becomes clear which things are worth investing in.
@howardadelman8218 Жыл бұрын
I recommend their moving blankets. They are inexpensive when on sale and they’re great for protecting finished projects if you are transporting them.
@The_Bigot Жыл бұрын
Yep. Tarps and tie downs too. The ratchet straps are kind of weak feeling I wouldn’t trust it for big stuff
@cewaffles Жыл бұрын
OMG Yes. They had a Sale last year, bought like 12 of them for about $2 each. We use them as Picnic blankets, Lining for tents, Day camping in the car (they go on the bottom under the blanks and over any padding), and also, moving things.
@charleselkins4546 Жыл бұрын
They have good deals on furniture dollies too. I have several and they have served me for years at a very low price.
@jonjacobjingleheimerschmid3798 Жыл бұрын
@@charleselkins4546 I've put my kitchen range on one of the steel reinforced. Makes it easy to pull out and clean around
@spidgeb3292 Жыл бұрын
Second that! I bought a bunch and they work just fine.
@natedoggschip Жыл бұрын
I've been making guitars for a year now and woodworking for 10 years, here's my top 10 gets from Harbor Freight. 10. Angle Grinders, look bad, work great! 9. Orbital Sanders, 2 for the price of one from a big box store, save time and lifetime of the sanding disks by not switching pads as much, have an 80grit and a 220grit at all times and they're just as good as anything at Home Depot 8. Casters, they are so dang cheap and work perfectly 7. GLOVES! they have a pair of gloves for 1.99 that last me weeks to months in the shop and I'm ripping apart old furniture and stuff constantly to upcycle into guitars 6. Sanding disks! They may not be the best but the cost per disk is minuscule, a 50 pack is 20 bucks 5. Miter Saws, unless you are a framer, they do the job just as good as the big names 4. Circular Saws, they're just as good as bigger names, try and see, just don't get HB blades for them, lol 3. Battery Operated Drills, they last forever on 1 charge and you can buy 4 for the price of 1 big name brand, and save time on switching out bits over and over. Get 4 and 4 different common bits. 2. Everything that you spend money on at the big box stores that lasts a week either way. Disposable Gloves, masks, masking tape... Get more of them pay less. 1. Small Clamps, f style and c style, they hold up and are extremely strong, I've only broken 1 out of 100 in 10 years
@big14tx Жыл бұрын
We’ve had two of the Chicago electric angle grinders in our shop now for 2 years and they are impressive. We use them regularly and in long durations and they continue to hold up.
@carportchronicles1943 Жыл бұрын
I have had a Chicago Electric angle grinder for several years. I dropped it two years ago and broke the plastic housing. I bought a Harbor Freight plastic welder and fixed it. I am honestly shocked the thing still works after all these years and abuse. It was well worth the $20 I paid for it.
@briand5083 Жыл бұрын
I actually bought a Chicago Electric miter saw off Craigs List like 5 years ago. Still works just fine. Granted, I paid like $40 for it. Not sure I would pay the sticker price for a brand new one.
@sinisterdeer7601 Жыл бұрын
Their $12 grinders are surprisingly good. My ex brother in law has had one for 5 years and he uses it all the time.
@daleferber2096 Жыл бұрын
You can decide if you want to do it and how "ethical" it is but when you do wear one out odds are good you can go buy an identical replacement and then you just keep the receipt and bring in the broken one within 30 days and as long as it is in the box and you have the receipt you will get a "free replacement" which you can just put on the shelf so you always have replacement/spare on hand Come in during lunch or some other "busy time"
@TBD3.0 Жыл бұрын
Me too 👍🏻
@TheCompyshop6 ай бұрын
Shop owner here. Every single person should buy their tools from harbor freight. If it breaks, replace it with something better. I guarantee you 95-99% of the tools you buy you’ll still own for years later. And by not buying name brand you’ve saved tens of thousands of dollars. Don’t buy the brand. Buy the tool. That $65000 snap on toolbox full of snap on tools isn’t making you anymore money than the Pittsburg brand from HB.
@MrAquinas126 күн бұрын
And you've supported slavery and child rape in the process!!!!
@kyleolson8977 Жыл бұрын
To be fair to Harbor Freight for the BBB rating, it's largely meaningless. People don't just go to BBB to say things went great very often, Especially for a large, high-volume no-frills business like HF. The level of complaints will be far outnumber people coming in to say "the cheap Chinese tools I got didn't break" or "lasted about as long as you should expect for something that cheap. If you know what you're getting into, and know what you need to avoid, as no-frills stores go, they're not that bad.
@wesnall6796 Жыл бұрын
@@1pcfred as a former ER nurse supervisor, I totally agree with this statement. That’s why I quit and found a job where I no longer lay hands on patients. I haven’t listened to anyone bitch in months.
@kwilliams2239 Жыл бұрын
BBB isn't totally meaningless. Some companies monitor their reputation closely and will make things right if there is a BBB complaint. These companies tend to monitor social media pretty closely. If there is a problem, these are good places to try to get satisfaction. OTOH, some companies don't care enough to spend any energy on customer sat.
@RonaldRugen Жыл бұрын
BBB Seems like a scam to me. They want you to join so it seems a bit like extortion
@davidnonnenmocher5122 Жыл бұрын
Own a business..never been harassed as much as I was by bbb...it's all about money with them..out of date and no power
@davidpeters8813 Жыл бұрын
ANY rating at the BBB is meaningless, companies can pay the BBB for better ratings.
@johnmooney9016 Жыл бұрын
Harbor Freight has one great buys for tools that you may not use everyday. I have several tools from HF, but the vast majority of my tools are name brand. I like how woodworking/woodworkers out there seem to be more concerned about bragging about tools or cost of tools then they do woodworking. Use what you have or can afford and enjoy your craft or hobby.
@industrialpalletworx3548 Жыл бұрын
Can't say it any better. Who cares what you have. As long as you get the job done what does it matter. I went forever without a nail gun. I didn't feel I had the need for it. I've since bought a battery powered nail gun. Life changer. So much faster than predrilling and hammering in finish nails. I was kicking myself for not making the investment sooner.
@geppettocollodi8945 Жыл бұрын
A true craftsman can do good work with mediocre tools. A mediocre craftsman can do no better than mediocre work with top brand tools.
@mezmerizer0266 Жыл бұрын
Damn good advice for enjoying your hobby/craft.
@DanielDroegeShow Жыл бұрын
If you made a nice piece and then you told someone that you did it with a $4 chisel set and $6 hand plane, how could I not respect you more?
@brianfreeman3676 Жыл бұрын
I have a wood lathe that I bought from HF back in 1994 and it is one of the best values I own. It's been a great tool the few times a year that I use it. If you need a top quality tool, go spend four grand on a brand name tool.
@joshuatatro4503 Жыл бұрын
Recent sub, and someone looking to build out a shop -- just want to say I really appreciate the level-headed approach to your reviews and willingness to take on broader perspectives when it comes to addressing brands and categories of tools and the things that make a tool "cheap" vs. "inexpensive." It's really useful, and vastly more helpful than the folks who just tell you to get the Festool product and be done with it. I have no problem spending the cash when it's something I'll use all the time and rely on, but for niche tools it makes more business sense to think about the cost compared to the utility and find the middle ground; your insight really helps with that!
@hootinouts8 ай бұрын
Good presentation. As a hardcore DIYer, I have been buying from Harbor Freight for years and have learned what sort of items to avoid. Naturally, we often get what we pay for. But for that occasional light duty application, the affordability and ability of HB tools to stand up to the job can't be beat. I even own a HB milling machine that is priceless. I had to do a little tweaking and customizing but it is truly a nice piece of machinery. The big box stores gouge you with the price of tools and they are all made in China anyway, so depending on what it is, I generally go to HB after doing some research in the reviews of items and such.
@Azurko Жыл бұрын
I've got that exact router bit set and have been happy with it for the last 4 years. So long as you don't ask it to hog out large amounts of material (which you shouldn't be doing anyways) and take your time, they work great.
@industrialpalletworx3548 Жыл бұрын
@@1pcfred agreed. I'm not building high end $10k end tables or something like that. I'm making a couple hundred dollar end table or shelf or whatever. The point is unless you're making super expensive high end products those cheap bits get the job done. I have the cheap ones from the big box stores and they are no different then harbor freight bits.
@industrialpalletworx3548 Жыл бұрын
@@1pcfred slow and steady seems to work pretty good while not taking a huge bite.
@crackedmasonjar Жыл бұрын
I’ll be honest I was a HarborFreight hater for a long time. Here, in the past few years I’ve slowly started to come around. Yes, there’s some really good deals in there but it’s sort of like how you would treat the dollar store. You get what you pay for.
@ancienttom97 Жыл бұрын
And you eventually come to know what to expect out of your purchases. If you have a problem with the tool you just bought, they have a 30 day return policy that hasn't disappointed me yet.
@kwilliams2239 Жыл бұрын
They're great for most consumables. Nitrile gloves are a really good bargain. Even their ALKALINE batteries are good, for the price. Again, it's HF. I wouldn't trust them in an expensive tool. I use only Energizer Lithiums for these.
@nickbrutanna9973 Жыл бұрын
The fewer moving parts, the better HF is (known exception: Anvil. The iron they use is far far too soft for a proper anvil). And as another commenter says, they are great for consumables. They have a small-size neodymium magnet, 10 for 2 bucks, IIRC, which is a very good deal. They have some different tweezers that are quite good. They also make a really really good 4x4x6 "tilt bin" for keeping larger screws, bolts, washers, and nuts in for organization. I just buy those by the pound from a local Rural King (think of a farm-oriented Wal-Mart... they sell live chickens and rabbits, for example!) which is by far the best place for getting bulk fasteners... P.S., another source for great cheap stuff is Banggood. You're basically getting stuff from the exact same factory in china, and slicing out the middle man's cut.
@rushthezeppelin Жыл бұрын
They've actually stepped up in the last 5 years and are sending American QC teams to China. If I'm rarely going to use a simple tool I'll go Pittsburgh but if I need a little more quality I've been very happy with their mid grade stuff like the Quinn line. I've generally been a bit wary on the power tools but I might have to start looking at reviews of the Hercules line after this video. I'm very much in need of a cordless impact.
@markh.6687 Жыл бұрын
@@rushthezeppelin I bought an HF 'Warrior' 3/8" cordless drill a few months ago; battery holds charge really well, and for a home DIY type it was a better tool than Menards or Walmart sold, and with a coupon it was a few dollars less. It also runs at a higher max RPM than most 3/8 cordless drills. I've bought a few other items like a ~24 inch 1/2 breaker bar for lug nuts; used it a few times with no problems so far. Price is not the sole indicator of quality anymore, since it's all made in China anyway.
@sonub5401 Жыл бұрын
I was in Harbor Freight about a week or so ago and they had a “newer” version of the Hercules table saw that had the same rack and pinion as the Dewalt job site saw. I think it was at the same price as it as well. I liked this video as you recommended other alternatives at a great price for the items you don’t recommend purchasing at HF. Every time I looked at chisels, they were astronomically high in price. The Narex you recommended seems like a great value for what you get. Thank you.
@djtblizzle6 ай бұрын
The biggest problem with HF isn’t the company, it’s the customers that expect their tools to operate like Milwaukee or Makita. You don’t go to McDonald’s and expect a five star meal. It’s a DIY store. If you’re using your tools to primarily make money, HF isn’t where you should go.
@jaredbryant8297Ай бұрын
Wrong answer, they’re starter tools for pros who don’t want more debt than necessary Get the Milwaukee when your business is established
@homerthompson6028 Жыл бұрын
I built my entire tool collection from harbor freight. I've even ended up buying some of the stuff they say to avoid and they work surprisingly well. The basic Pittsburgh tools feel cheap but will last if you use them only for what they're rated for. The Pittsburgh Pro line is great. I regularly abuse them and they hold up well.
@iamnotafraid Жыл бұрын
I've only had a few issues with their products, and both times, I returned to the store and either got a full refund or a tool replacement, with no issues following afterward.
@LivingCommonSense Жыл бұрын
Nothing wrong with that plan. If the HF tool lasts, you saved some money. If it doesn't, you know what features to spend on the next one.
@cbmech2563 Жыл бұрын
I'm a heavy truck mechanic who got his box stolen in 2013 and to rebuild my tools most have been harbor freight. I don't buy "good" I stick with better and best and depending on the item I may buy some other brand, like my 1/2 inch impact is a nitrocat 1250. For air grinders that I need occasionally but that spend a lot time in the, box central pneumatic works great. For battery tools I started with Bauer but because of some of the tools available in the Hercules line I've started to transition to Hercules. I've been extremely pleased with both lines. I've been abusing the angle head wrenches (to 2") for 8 years and haven't had one fail yet. You can't beat the impact sockets, I have shallow and deep 1/2 and 3/8s since 2013 and I've only broken one that I use all of the time, walk in the store and walk out with a new one.
@BlackbeardKNAC Жыл бұрын
Same, I would not have been able to build a shop without harbor freight. There are snobs in everything and tools are no different. Often the people telling you not to buy harbor freight are standing in front of a SawStop, a $10,000 planer, or some ridiculously huge CnC that I will never have access to. Literally, ALL of my knife shop is harbor freight tools and I have knives that sell for hundreds of dollars.
@JoshJackson13 Жыл бұрын
I'ma farmer and the Pittsburgh wrenches are good and cheap. I like having 5 9\16s compared to 2 craftsman. Both are made in Taiwan metal
@forzaguy1252 Жыл бұрын
Being a modeler i love their needle files and micro drill bits. Perfect for use on plastic
@kamaeq Жыл бұрын
Bingo, need to know what you want them for. Building minis, HF stuff is great. OTOH, I have quite a bit of tropical hardwood I brought back from overseas that will not only tear up the big name brand tools, but even industrial woodworking machines take significant wear and tear.
@VanWelij Жыл бұрын
The wrenches are for more than just household DIY. I've been an industrial Millwright since 2007 and I started out with a Pittsburgh set up to 2". Those things have seen extreme torture in many heavy industrial settings and have held up remarkably well. They're not as good as Snap-On, MAC, or even older Craftsman, but for the price, you can't go wrong. My 2" Pittsburgh wrench has had 8-foot extensions on it torquing down anything from Evaporators to ID Fans and the teeth aren't spread open even a little bit. I'm not going to comment on ratchets or any of the gear wrenches, but the simple basic wrenches are excellent for the price. Plus, if you lose one it's cheap to replace; something that'll happen to you quite often on a jobsite. The Icon brand is not cheap at all and rivals the higher-end wrenches you get from Lowes/Home Depot/etc. It's no tool truck wrench, but those are essentially overrated anyway. I guess my goal is to not scare newer apprentices or up-and-coming journeymen from Pittsburgh wrenches at first. Sure, you can upgrade as you advance your career, but I've seen too many newcomers waste their entire paycheck on tools that were just unnecessary. Put that money towards your retirement and quit buying into the hype.
@lanzer22 Жыл бұрын
Stuff like the $10 grinder and $15 vibrating multitool are actually really good. They have very little moving parts and they get the job done. I've used both for many years before moving to cordless versions from better brands, but they're still running fine, and at that price it's even cheaper than renting.
@alexknight71917 ай бұрын
For the occasional use mine gets, I love my $10 grinder! If it dies, I'll just take that as a sign that it's time to buy a better one.
@johnmack537 Жыл бұрын
After you and many others recommended those Bremen parallel clamps, I went to the nearest HF for a couple of 48” at their listed $39.99; “out of stock”. Still out of stock several months later, but they’re now listed at $44.99; a 12-1/2% price increase. Lowes now has 48” Jorgenen parallels at $39.98, 24” at 29.98.
@tangoindiamike9189 Жыл бұрын
Since the pandemic and Bidenflation, I've noticed that HF tools have increased significantly and I often find "as good as" pricing at Lowe's on better known brands. However, HF still does some great sales, but a tool buyer has to be very discerning on quality and comp pricing elsewhere. In other words, it pays to check your other big box stores before biting on a HF sale price, unless it's an item that quality is not as critical, like disposables and consumables.
@mariondorsett Жыл бұрын
I've only discovered HF in the last year. I can say the router bits work great on pine... I haven't had any issues w/ their locking casters and ball bearing casters. I've also purchased tarps and moving blankets when they're on sale, and consuables like the rubber gloves, and paint supplies in the best category.
@arawtgabi Жыл бұрын
I buy the moving blankets those magnetic screw pans. Other than that they have an occasional good buy.
@ancienttom97 Жыл бұрын
I use their casters. They work for me and their cheep. I also use their tarps but they are cheaply made and only last a season but they are also sold very cheep. I consider them as consumable items. As far as their router bits go, they do work but dull rapidly and I will replace those with a better brand.
@4cClubT Жыл бұрын
Can't beat the price on castors,or solid rubber dolly wheels,Harb Rocks
@ancienttom97 Жыл бұрын
I am also a HF Junkie. I had their plunge router for exactly one day and returned it. When I set it up and tried it out. the plunge guides were so sloppy. I could not get an accurate plunge into the work piece. I have a couple of sets of their router bits and have used a couple. They seem to cut okay. At the price I paid for them, if they dull up on me prematurely they will have served their purchase at the price I paid for them. I will replace with Bits&Bits or another quality brand when they do. AS far as their casters go, I think that they're a little over priced when I can buy their small flat wood dolly for $17 and have to pay about $20 for just the caster wheels.
@mariondorsett Жыл бұрын
@@ancienttom97 it's funny you say that. My wife and I were looking at some coat hooks last night, and she saw some mounted on a board, and you just hang the board. She didn't like those hooks but we were contemplating buying the board w/ the hooks for less money, and tossing the board ;) However, I've not seen the locking caster wheels on any dolly, so that trick won't work for me there... but I will keep this idea in mind.
@IronMan-bn4wl Жыл бұрын
Another excellent review. I recently bought the Hercules 12-in sliding miter saw and used it for a project. I love it! For the money I feel like it is more saw than I even needed. I love the power of the motor, the accuracy of the cuts, and the stability of the cutting platform. I put it on the Hercules miter saw stand and it makes a perfect combination. I can stand it up in the corner of my shop out of the way until I need it.
@c00LKIDsix910 ай бұрын
Harbor Freight has some real gems in there sometimes. My dad used to own a mechanic and body shop and we had several of their smaller US general rolling toolboxes for new employees who had tools but no boxes. We still got a few of them years later even after we shut down after he passed.
@plektosgaming2 ай бұрын
I got one of their little fabric "toolbox" bags for $4. Works great. Stuff like that is taking so much of my money. lol.
@cerebustm Жыл бұрын
My favorite HF find is the 3/4" pipe clamp with base. There are very few moving parts and it doesn't even matter if they are square or not. I put 2" thick hardwood pads on mine and slowly sanded the pads down until they fit perfectly flat. If you combine these with a 6' long steel pipe, you have clamps that can pretty much handle nearly any job for $40 or less.
@212caboose Жыл бұрын
I actually JUST noticed the 3/4" pipe clamps! They're FAR cheaper at HF than Amazon or the big box stores!!
@Dewey-wz4ny Жыл бұрын
I agree but they were $5.99 just a few years ago not $11.99 like now.
@sehabets Жыл бұрын
Two things I would add, I go to harbor freight for disposable nitrile gloves, they are reasonably priced and work well for a consumable product. Second, as far as the router bits go I've been using the round over bits that come in the maroon packaging and are painted black for years and they are still sharp and work great. But like with all things mileage may vary.
@barrydonewar3785 Жыл бұрын
My Bauer 20v drill has never failed me yet. The battery life is incredible...20 straight days without a charge. I also like their clamps and the hand tool sets are good to travel in my truck box for a quick repair.
@doug38199 ай бұрын
I've got a bauer 1/2 inch impact wrench, I use it three times a yr to take blades off my riding lawn mower. I've never had a problem with it. Why would I go to lowes and pay 3 to 4 times as much. Many people buy products there I believe because they are not going to use them often.
@dudeharmonious Жыл бұрын
Latest Herc table saw is pretty good now. The v2 is rack and pinion plus some other quality of life features. Been using for a few months, no complaints so far. Only real drawback is it doesn't support dado blades. :/ Edit - Almost forgot, plug for the Herc router. Its super OP for the price, great value and performance.
@oldtireman4665 Жыл бұрын
Lots of good info here. I will also vouch for their power cords, especially the 10 gauge. I have two 25’ and a 50’, all with the lighted triple ends which are great if you’re not sure of a good connection. Never go to a job site without them. Price is at least a third lower than the big boxes. 12 gauge cords are also good. Doing a lot a stain and finish work? The nitrile gloves are great. Get the 9 mil. I’ve reused the same pair to do hundreds of linear feet worth of oak trim. Plus, they have XXL sizes! I concur with your assessment of the Fast Cap tapes. I swear by the 16’ lefty/righty. Actually, Fast Cap has a lot of good, reasonably priced goodies.
@ST-0311 Жыл бұрын
Gotta love the "Avoid at all costs, because I ASSUME," advise. I followed the conventional wisdom of buying a cheap set of router bits to see which of them I used the most then replacing those with quality bits. Got that set from Harbor Freight for that purpose, and 3 years later I have yet to replace any of them. I wonder why 97% of reviewers would recommend them? As others have pointed out the job site table saw has been totally redesigned. Perhaps an annotation of "Old Model," would be appropriate at this point. Also, while the Pittsburgh ratchets and wrenches may be fine for "Using around the house," the Icon line are professional grade tools, and deserve to be recognized as such.
@Lithic_Goose Жыл бұрын
I would counter that and add that I use my Icons "around the house" and my Pittsburgh tools are in my go bag. Reason being if I lose a wrench out of there, it's not going to hit the wallet terribly because I forgot a wrench at the junkyard. I keep the Icon at home because I know I won't be in a situation where if I leave one laying around, it won't grow legs and walk into someone else's bag
@ST-0311 Жыл бұрын
@@Lithic_Goose Good plan. Icon tools aren't things you want growing legs.
@ryan74701 Жыл бұрын
The Hercules miter saw is a BEAST. The new Hercules plunge router is great also. Their tool boxes are great, their ICON tools are VERY good. Their 2 hp Dust extractor is supposed to be decent for the price, upgrade the impeller with a WEN for $50 and change the bag to a canister filter and its twice as good.
@robertjames-life4768 Жыл бұрын
Agreed! Precision instruments rarely exists in the Chinese Cheap Hallowed Halls of Harbor Freight. That said I did get the new variable speed bench grinder recently and it’s great. I mostly go for magnets, zip ties, cheap paint brushes etc.
@steelsunpi Жыл бұрын
I've got the Hercules job site table saw. Actually my second, I had the first generation and brought it back to get the second gen version with the rack and pinion fence. Overall, I like it, especially for the price. Yes the fence can get sloppy, but a few adjustments gets it right and it works.
@ThePainkiller3666 Жыл бұрын
I miss my first gen I had to trade it in to get the rack and pinion table saw because my friend ended up losing the fence on the first one. The 2nd gen feels has a cheaper more plastic feel to it.
@shawntodd10779 ай бұрын
I’ve used Harbor Freight’s tools for about four years now. I started out with the Bauer kit they had four years ago on Black Friday. It had the 20v drill, driver, circular saw, reciprocating saw, and a light along with 3 1.5ah batteries and two chargers. I then bought the hammer drill kit with a battery and charger. I did have to take back the drill as the chuck broke about a year into it. They replaced without any issues. Since then I’ve purchased several Bauer 20v tools. I also have the Hercules 12 in sliding miter saw anti love it
@camm668 Жыл бұрын
Definitely some great deals there and over the last 5 years, they have really been stepping up the quality of their product lines especially with the Icon, Hercules and Bauer line. Also the Badland winches are really nice and comparable to winches costing twice as much.
@stchman Жыл бұрын
I've bought lot of tools from Harbor Freight, pretty much all of them are the lifetime warranty Quinn, Doyle, Pittsburgh, etc. Their hand tools for working on cars I think are pretty darn good. From what I have read, there are a lot of mechanics in shops that use Harbor Freight tools on a daily basis.
@dmandman9 Жыл бұрын
I do. I haven’t had any problems with their Quinn hand tools or Earthquake air powered impacts. I’d steer clear of the lowest brand of air tools though if I was using them professionally.
@LYTOMIZE_Woodshop Жыл бұрын
Pretty much sums up what I found when I visited one for the first time. Bought a couple of the smaller clamps and some consumables... go in with your eyes open with some knowledge and you can escape with a few goodies!
@ourBrainF00D Жыл бұрын
The production value on this is crazy good. I've been getting into the "tool" and handyman world and I'm so tired of the bad audio cell phone videos. Thanks for changing it up.
@usaveteran18133 ай бұрын
The worst retail experience in my entire 76 years took place six months ago at the store in Orland Park, Illinois. I then traveled to their store in Downers Grove which was very nice with a wonderful store staff. Apparently consistency of quality of customer service is very spotty.
@sneekc21467 ай бұрын
Mechanic experience here the icon stuff is super solid. The Pittsburgh flex head long handle ratchets are nice. Also Daytona jacks snapon went after them because they were worried about the competition which if you know snapon they usually far exceed everyone else
@leytonmcnamee4 ай бұрын
Snap on exceeds nothing but being a bandwagon, I buy their pliers just for the hats
@sneekc21464 ай бұрын
@@leytonmcnamee I mean I think it’s poor taste to say they don’t exceed others. I get the fan boys are crazy I can take stuff apart all day long with the Pittsburg stuff. But the quality is far better with icon. Then stepping up from that is snap on quality. Is it worth the price difference? To me no not really but I still love snap on
@leytonmcnamee4 ай бұрын
@@sneekc2146 icon is the equivalent of an electric lawnmower, it works for small stuff but not like hard usage, Mac is just all around the best
@themaker4216 Жыл бұрын
I use the Hercules V2 table saw with the RP fence and it’s really a nice saw once you do the initial tune up. I was able to crank out some cabinets with it and I was very impressed with the accuracy for a harbor freight tool
@djdaveott Жыл бұрын
Agree with your comment. I remodeled my restaurant and bar with this table saw. It surpassed my expectations.
@martinoamello3017 Жыл бұрын
No thanks. I moved on to Sawstop and no longer worry about my body parts and a Sawstop almost never needs major adjustment. When it comes to possibly chopping off pieces of my body cheap is not an option. I build cabinets for a living now. I can't afford to be missing fingers. An hour visit to an ER to get a finger reattached will cost a WHOLE LOT MORE than the most expensive Sawstop model.
@frankbrown30476 ай бұрын
Just want to say I really appreciate your critique on Harbor Freight Tools. You were fair and unbiased; Additionally you pointed out those tools you found to be of value. I am one of those people that purchases harbor freight tools, at least certain ones. I do have a Chicago Electric belt sander. I got it thinking Ill use it for a particular job and if it craps out well so be it. I was able to use it on 2 deck resurfacing projects and it is still going strong. That sucker wont die! It's 15 years old now. I also have the electric impact wrench that has received heavy use. Only recently changed out the brushes (brushes are included) after 12 years....Still kicking. You could not have said it better when you mentioned the metals in the tools are softer and lack quality. I stay away from their screwdrivers. I've had good luck with their Pittsburgh line of ratchet; no issues. I am of a generation when people oftened complained about items made in Japan. We should be so lucky to have more made in Japan and not China. Japanese chisels, for example, can't be beat. As for their automobiles....well Toyota cars speak for themselves. LOL! Bottom line is it pays to be informed; read reviews and then draw conclusions regarding purchases. Your videos are very informative and I have learned a lot....keep 'em coming!
@Nolano386 Жыл бұрын
Their digital calipers are a good deal. I've been using a pair for over a decade, even in my machining class with super tight tolerances. I have a pair of mitutoyos also but I bought an extra harbor freight caliper just so I could have one in the garage, one at my desk, and one at my 3d printer.
@matthewpolzin1687 Жыл бұрын
They are straight trash
@ol.grumpy.bastard Жыл бұрын
Yup. I have one in my garage, one in my basement, one in my glove box, and one in my kitchen junk drawer. They're always coming in handy for something.
@steelisreal4313 Жыл бұрын
was gonna buy a used mitutoyo caliper but didnt want to pay $60 so just got a HF one instead. Good enough for my occasional use.
@boosterseat9967 Жыл бұрын
It looks like your store had the old table saw on display, before manufacturers had to update them with wider feet. The updated model does have a rack and pinion fence. I’m not a fine woodworker, but it works great for construction.
@naturaIIydifferent Жыл бұрын
The Hercules table saw used to have a rack and pinion fence when it was first released, at least as far as I remember... Den of tools did a side by side with the DeWalt of the same size and found the Hercules to be almost identical. The Avanti airless sprayers are fantastic. The all metal one for 650 rivals Titan and Graco sprayers that are double to triple the cost. The Central Machinery floor standing drill presses, benchtop wood lathe, 14" bandsaw and the mini lathe and mill are all great for actual shop tools. Just a couple of good ones you missed or didn't know about. Everything else you said was right on the nose, except that table saw. Maybe get one in the box and do a review? I know the floor models can get messed up. Maybe they did away with the rack and pinion? Anyway, cool content as usual. Hope you guys made it through the storm the other night. Up here in Upstate New York we caught the tail end of that wind... It was epic lol. Peace and love to you and the family ❤️💛💚
@RealJeep Жыл бұрын
The China Freight tools are just knock-offs of legitimate brands using stolen technology and designs.
@blackfrost273industries4 Жыл бұрын
As a former employee that also did research on the tools of the time. Almost everything you've mentioned is really accurate. The bar clamps are good, The machinist lathe is a good introductory lathe for small pieces and rifle barrels. The torque wrenches have been reliable over the years. The dust collectors, the sandblast units, almost all of the woodworking tools are decent. I agree the chisels are okay at best. The woodworking seems to be the shining area. I would stay away from consumables as a primary product. Like sandpaper. But they do well and they do great in a pinch. The Bauer, Hercules, earthquake lines are definitely better than the rest of their tools. The Doyle, Bremen, quantum, and other newer names are also really good. I started in '16 and left just before 2020. It's a weekend warrior store. Sufficient. If that makes sense
@ProTechEpoxyFloors Жыл бұрын
I find the customer service in store to be excellent. They will also take anything back for any reason within 90 days and you don’t even need a receipt if you used your phone number. They have come a long way in their quality in their better tool lines. I have a bunch of Bauer corded tools that I haven’t killed yet. I know you can’t cover all their gems but there are quite a few in the store. One of my best purchases there is their drillmaster pocket jig. Great video as always!
@michaelparks3106 Жыл бұрын
HF is great for the casual or weekend warrior handyman. Many professionals who make their living with tools don't (and shouldn't) depend on HF tools, but that's not the market HF is going for. When I made a living working on cars, my tool box was full of Snap-On, Mac, and other quality tools. But when I needed a 1/2" rachet to throw in my RV to work the stabilizer jacks, I got a cheap HF model. For occasional light-duty work, the HF rachet was $13 - the Snap-On is $195. If the HF breaks (which it probably never will, considering the light-duty), I would not feel bad throwing it away and buying another one. A good worker knows to use the right tool for the job.
@lukejoyce1107 Жыл бұрын
On odd tool that has been serving me surprisingly well from harbor freight is an English Wheel for sheet metal rolling and planishing. Sort of makes sense though - it's mostly just some solid metal rollers and a heavy frame, none of which goes under crazy stress or anything.
@kennnva551 Жыл бұрын
I agree with this summation of HF tools "almost" 100%. My exception would be the wood-handled HF chisel set. I bought a set and it did not take me long to get 'em perfectly flat and sharp using wet stones. What has impressed me more is they seem to hold that sharp edge for a considerable amount of time. I'm not woodworking every week, but the last time I sharpened them was over a year ago.
@nickbrutanna9973 Жыл бұрын
Their jack plane, however, is absolute garbage. Not recommended. Hey, it's cheap. That's just fine.
@cattigereyes1 Жыл бұрын
For the little amount of wood working I do. A short term chisel is fine for me. New door plate lock and such. I am not a carpenter by any means. But small projects at home type. Always have been interested in wood working. Tried to build a shelf and let’s say realized I needed way more equipment! Ouch.
@mikalbrewer9031 Жыл бұрын
Hercules job site table saw has a rack and pinion fence. A very nice one I might add. It is not the most robust product, but for a job site saw it is excellent quality. I bought the table saw for a kitchen remodel project I was working on out of town. I assumed I would be done with it when I left, but I ended up loading it up in my truck and bringing it home to replace my Rigid job site table saw. It definitely had less use, but it was also just better engineered and functionally worked more accurately. It is also substantially more compact. 10/10 would buy it again without hesitation
@timdeniserhodes6450 Жыл бұрын
As for the Hercules table saw, they have up graded it form the one you showed in your video. I bought the new stile and have been pleasingly impressed. The fence can now be locked down with a set screw to keep it parallel with the fence. Fence adjustment is on a rack and pinion system which I really like. And it looks like a Dewalt 7485 twin. Will it run a dato stack? No, does it have the power of a $1000 saw? No. But as a entry level, or a small shop table saw, it’s not bad. It also come with a combination blade that side by side looks identical to a blade . By the way love your channel!
@timdeniserhodes6450 Жыл бұрын
Correction on my last reply I meant to say the Hercules comes with a combination blade that is identical to a Diablo blade
@rogermccaslin5963 Жыл бұрын
@@timdeniserhodes6450 I've wondered about how they could make those blades so cheap and if they were any good. I tend to buy better quality blades after starting with cheap. The first $100 10" saw blade I bought was like opening up a whole new world to me about 30 years ago. It cut so much smoother and cleaner, I could never go back to cheap for my table saw. But now, even cheaper blades seem to be better quality (if KZfaq reviews can be believed 😄). I might have to try one. Just as an FYI, you can click the three dots to the right of your comment and edit it if needed rather than adding another comment.
@scottbitz5222 Жыл бұрын
I love my Harbor Freight drill press as it's been very good for me for a couple of years for making pens or other projects of the sort and has held up quite well. I did get the metal yardstick years ago, however, it's only used for crafting with cutting fabric where accuracy isn't all that important and it's great for cutting straight lines with a rotary cutter. I will say it does look like their "best" brushes are actually comparable in quality to the "good" brushes you get from big box hardware stores, however, I'm also of the opinion that I only used those when I was broke and trying to paint a house or for stain or poly on something that was going to get covered in stuff and a stray hair in the finish will probably get worn off or hidden! Either way, I am a "I know what I'm getting when I go in there" but do like it for things here and there.
@Murlockwarrior Жыл бұрын
Thanks for the great video. I love HG as it gets me a good entry into trying out new ways to putz around my garage and basement workbench. I would like to make one small change, and that is about the paint brushes. I live in Wooster where they are made and it cracks me up whenever someone pronounces it who has never heard it. It is the "oo" from "book", "took", or "whoops, there goes my spending budget on magenets". Please read this in a lighthearted and amused tone and not angeynlocal defends the proud name of Home Town America vehemently. Cheers and keep the vids coming!
@coreyschmutzler585411 ай бұрын
I actually use the 4 pack router round over bit set from Harbor Freight with the black colored bits and they work great. I build subwoofer enclosures on a regular basis and I use these bits on every project. They’ve held up very well for a year now with no issues at all. I also have some very high end bits as well from Mobile Solutions and the Harbor Freight bits that I use have been just as durable.
@embracethesuck1041 Жыл бұрын
My golden rule is avoid anything with a cutting face that you can't sharpen. In addition, anything should be considered disposable. Still, they have a lot of value for money especially for single-use specialty tools.
@ReformationHomested Жыл бұрын
As a mechanic and wood worker I can say that the Icon line is a very good line pretty much without exception. Most of those tools are a direct copy of something Snapon or Mac but for 1/4 the price and the same warranty. The new USG 34” full bank service cart is a snapon copy but I actually think HF did better (and I paid $400 because it had a dent). I would also say that if you aren’t sure how often you would use a certain tool that you are curious about, get it from HF and if you use it a lot plan to upgrade, if you don’t use it much then you aren’t out a bunch of $.
@LoveMyMagMoreThanYou Жыл бұрын
This is the best advice about buying from Harbor Freight that I've seen. Exactly how I think about Harbor Freight.
@jeoffbenzos4959 Жыл бұрын
I get all my hand tools from there and have been impressed with them. Knowing they're cheaper quality, I don't have to worry about breaking them due to the HF lifetime warranty on hand tools.
@paulkile9998 Жыл бұрын
I bought a bunch of Harbor Freight metal yardsticks, but cut them up into 4" lengths, drilled a hole near the end, and fastened them together with threaded rod with nut spacers. Presto...a storage rack for plier type tools that fits in your tool drawer and holds the tools on edge.
@austinsalyer8966 Жыл бұрын
I have the new Hercules table saw with the rack and pinion setup and I’d say with the upgrades they have made to it, it’s a much better saw and comparable to a lot of the higher end saws. They gave it a wider foot print and a bigger table. I’m just a weekend warrior but I’ve built 3 screen doors and enclosed a carport using this saw. It’s great for the price if you are looking at this as a hobby not a pro. The fence is a great upgrade and I’d say the only down side for this saw is you can NOT use a dado blade set in it.
@c.c.1070 Жыл бұрын
The absolute best thing I ever bought at HFT is the wooden machinist toolbox they sell for $89, in fact I have 3 of them. They are also great for storing my sketching supplies and Copic markers.
@97minitaco Жыл бұрын
I actually bought the #4 plane and the #33 to mess around with and after some flattening they actually work REALLY well. I've had them for a couple of years now and use them a few times a month.
@ericliddle7556 Жыл бұрын
I stopped in at Harbor Freight today for the first time. So many of the items you mention from the 3 pack of squares, the F style clamps, router bits and the chisels jumped out at me...I'm sure they're fine tools if you're looking for something to smash around/really can't afford anything more, but for the time being I stayed clear.
@sweetharmonyapiaries Жыл бұрын
Their Chicago dust collector is an absolute beast, especially at its price range. It's definitely a tool I'd recommend.
@Weshopwizard Жыл бұрын
Interesting.
@tangoindiamike9189 Жыл бұрын
I've nearly bought that dust collector a few times. Maybe.......someday.
@mwaynem Жыл бұрын
Another very good organization product is their plier organization tray. I have one in my tool box and it works great. Also be careful buying wrenches especially set on special sales. Ive found that many times they are not a full set and will be missing commonly used sizes.
@markh.6687 Жыл бұрын
Oddly enough, to get a set of metric deep sockets for a lug nut set, I had to order one of Walmart's 1/2" sets; HF and others brands skipped sizes I needed when some goofball put different size lug nuts (same thread, different head sizes!) on a used car I bought.
@Benefits Жыл бұрын
The best Harbor Freight deal I've ever found is their Bauer brand 20v cordless 3.5 gallon wet/dry vacuum. $55 and it came with a free 3 amp hour battery. That vacuum outperforms my Milwaukee vac of the same style, which I totally didn't expect. Plus it's $165 cheaper than the Milwaukee and holds 1 gallon more capacity.
@ryanlake7603 Жыл бұрын
Great video, hobo freight has it's perks. If you need a tool and you know it will be used once or twice in your whole life then it's perfect or maybe it will work with a bit of hassle but because you won't need it again it's worth it.
@frankj.sancheziii4694 Жыл бұрын
Hello Matt, another awesome video, very informative. And yes not everything is created equal at Harbor Freight for example a few years back I bought a 10" Chicago Electric miter saw because the price was right for what I could afford at that time. But the saw itself was not great, every time I went to use it I could never get a square cut & I just got tired of fiddling with it to try & get it square & I was past the return period so I couldn't return it. So I eventually broke down & bought a Ryobi miter saw from Home Depot & right out of the box it was true & square. Even when I switched out the blade for a Diablo blade it remained square & yes I learned my lesson the hard way about buying certain tools from HF but not everything is that way. But I would like to ask your opinion about a certain tool that I've been eyeing for a while from HF it's the Hercules 8" variable speed bench grinder. The reason I chose it is because of its variable speed & 5 amp motor compared to the Bauer 2.1 amp grinder, I didn't want something that was going to possibly bog down on me. Also it's a tool that I would be using on occasion with a wire wheel to clean up bolts & such when I do automotive repair so I didn't want something too expensive plus it's a Hercules & not a Chicago Electric. Any info or opinion that you might have on it would be greatly appreciated like if you know someone who has one or heard something by word of mouth. Well sir I think I have made this comment a little too long, thank you for your time & have a blessed day.
@johnnyolson258 Жыл бұрын
Their icon stuff is pretty good, their folding bar light I actually prefer over the streamlight that it's trying to knockoff. Likely not as strong but its lasted my abuse since it came out. Their knipex knockoffs are pretty good quality but you aren't saving that much money so the price difference may not be worth it. The icon pliers wrench and Doyle water pump pliers are both well made.
@malfactor1 Жыл бұрын
Their swivel head breaker bar is great. I also got some mallets and crowbars cheap there. My rule of thumb is harbor freight is good enough if you just need a chunk of metal to beat something with
@eswift8318 Жыл бұрын
After watching several comparisons, I saved myself some money and bought the Hercules table saw when it went on super sale (and of course picked up some free moving blankets with it). The fence stays square enough for me. It can be a little fiddly to lock into the correct spot if you need to be precise, because when you press down on the locking lever, the fence can shift before it locks down. So I always have to recheck my measurement after it's locked. But once it's locked, it's locked and square. I've made drawers and picture frames with it and joints come out perfect. Power-wise, I've done a few heavier cuts through thicker hardwoods. Recently cut two pieces of red oak glued together - 3/4" each - and you could hear the motor pushing a little, but it went through them clean with tear out or burning. So I'm guessing if you are doing a lot of heavy duty work, this won't be up to the task. But I think it's got plenty of power for the average woodworker.
@betojaquez07 Жыл бұрын
HF automotive tools are great! Especially their 24" and 18" Ratchet breaking bars. I think I bought the 24" for like $20 which is a super good price compared to all competitors. I also like their low-profile floor jack which I also bought for a good price. HB is great for the average DIYer. I agree with 731, I would not buy power tools from HF but I would buy a lot of their other products.
@spoonfind583 Жыл бұрын
Their two top brands of power tools are some of the best. My yellow power tools now sit on the shelf. I like the HF ones better. I have used some of them a lot and abused them like the yellow ones. They have stood up better. Also their Pedator motors and generators are very good.
@UpcomingJedi Жыл бұрын
You can also find the paper towel holder as parts. One round dowel (Cut to fit), two screw eyes for each end and some paracord or mason line to hang this from the ceiling. Its out of the way yet paper towel is within easy reach when you got greasy hands.
@MGBguy72 Жыл бұрын
So happy when Harbor Freight opened a store closer to my home. Good prices on single use paint brushes, nitrile gloves, tarps, and one of my favorite HF tools; their Compact Air Needle Scaler. Their clamps work well for me for making small boxes, drawers, etc... Recently bought their Quinn 1/2" drive torque lug wrench and a 19mm socket to do my winter wheel changeover. KZfaq videos are great, but Harbor Freight reviews would be my first go-to.
@bferguson9277 Жыл бұрын
Among my purchases there are a floor jack, pneumatic cabinet nailer, pneumatic hoses, belt sander, hammer drill and assorted small items. The hammer drill gave up the ghost after one project. The belt sander held up for a few years worth of moderate use. The floor jack and cabinet nailer still work great (10+ years). Drill bits, hole saws and the like don't have the quality of the upper tier stuff and are pretty much one-project throwaways.
@RyanGeyerCycles Жыл бұрын
Late to the party, but I also have the Hercules table saw. As others have pointed out, your video shows the previous gen with a "clamp on" fence. Mine is the second gen with a rack and pinion fence. The fence *did* require some tuning to get it square and accurate, but it's been flawless for me so far. My use-case is cabinets and some shop furniture. I'd *like* to do some more fine woodworking with it, and my experience so far leads me to believe I should have no problem when I use it for those projects. Great video, as always. Thanks for the great content.
@kasbakgaming2 ай бұрын
I've used a Chicago Electric angle grinder from Harbor Freight for years, it has always done fine and taken everything I've thrown at it. I originally bought it when I was tiling my basement floor and needed something to cut just a couple of spots that I couldn't do with hand tools and didn't want to spend the money to buy or rent a tile saw. That was about five years ago, and I've never had any problems. I think it's less a problem with tools that have more moving parts and more tools that need to have any sort of accuracy to them. Even then, most of the tools are fine to use as a base if you want to custom build your own tool. I did that with a tabletop lathe from them that I wanted to custom build an extension to, using it for small projects like knobs, handles, and toy wands for kids in my family.
@chrisp9046 Жыл бұрын
The Bremen vice grips are awesome for the price. I use them in a weld shop daily and abuse them. Still have the first one I bet years ago working like when I bought it.
@projectbumblejeep4190 Жыл бұрын
Never have I ever had an issue with HF customer service. On the very few times I've had to get a tool replaced, the HF employee just walked to the shelf where the new tool resides and handed me a new tool and sent me on my way. Just about as easy as it gets. As far as I'm concerned, a life time warranty is a life time warranty. From my own experience , based on the amount of HF tools in my box, I've had to have very few tools break. God belss, stay well.
@jbdragon32956 ай бұрын
I have a HF small air saw. I got it to cut out truck grills for aftermarket grills. It worked great and I still have now. I got some really nice clamps from HF not long ago for where I work now and they’re great. I’ve gotten their dolly’s to move around heavy equipment. I have Snap-On, Mac, Matco, Craftsman, and other brands of tools. But the HF stuff I’ve gotten has worked well.
@douglasabler3581 Жыл бұрын
Commercial electrician here. After you’re in the trade a while, you learn which tools you can skimp on, and which ones you need to spend top dollar on. All my power tools are DeWalt or Milwaukee. All my hand tools which are specific to the electrical trade are Greenlee, Southwwire, Klein or Ideal. Same with benders and fishing tools. Hand tools such as wrenches are from HFT. I bought my modular tool and parts organizer from HBT about a year ago, and so far it’s great.
@raymondbunkofske4702 Жыл бұрын
For measuring tool like squares and rules all of your comments about HF also apply, in my experience, to Lowes or Home Depot. I took two speed squares out of one box and they didn’t even match over 6”.
@FOURfabrication11 ай бұрын
I've not had a lot of issues with HF stuff. And their return policy is top notch. I got a tap and die set (probably not something to buy from there but I was on a budget) and when I broke a tap I went in and asked if the lifetime guarantee meant I could get a new tap - the lady said "a new tap, no - you get a new set"
@matt7126 Жыл бұрын
I would have to agree with all the weekend woodworkers out there. They have some great and affordable stuff at HF. I just picked up a hercules router a few weeks ago and its built quite well. Grabbed some warrior brand router bits to make some dados and dovetails and they work well and get nice and smooth cuts when you use a few passes like you should. Then I picked up a bauer corded jigsaw a few days ago for $30! The one I grabbed had a bunk laser line and the blade would wobble a bit at highest speed setting. So guess what? I didn't even use it and exchanged it for another one and this one was right as rain. Nice and clean laser line and no wobble at highest speed setting. They were super nice about the exchange too. Only asked what was defective about it to report it. Moral of the story... EVERY company makes defective units. Don't keep it and be pissed. Just return or exchange it and get back to work. And if those tools are YOUR lifeline for income then maybe YOU should invest in top dollar tools. Not everyone needs tools that break your budget. Ps I don't stress test my tools. I don't want to risk my safety to make a PSA for others. I figure another way to get it done safely or walk away until I get a tool that can accomplish what needed to get done.
@arturoramirez37185 ай бұрын
I bought a floor stand 16 speed drill press from Harbor Freight over 20 years ago & it's still running. I'm a weekend warrior & it being a Central Machinery product has been great for me.
@matthewwhiting6191 Жыл бұрын
HFT employee here, a tool i personally reccomend to alot of people is the low end Warrior drill driver. perfect for the homeowner who might only need a drill occasionally and ive done a few big jobs with it and its pretty solid
@libraeotequever3pointoh95 Жыл бұрын
I am an occasional DIY-er. I don't regret getting the Admiral 12-inch compound-sliding-miter-saw from Harbor Freight. Good value for my money, I feel. I mounted it on a Ridgid "miter-saw-universal-vehicle" portable stand. No regrets.
@stuffthings96185 ай бұрын
It's simple. HF is for the homeowner and layman. The guy who only needs a set of pliers perhaps once in a lifetime. Not the dude who has to use it 20 times a day throughout a 10 hour shift
@johnnycashh7148 Жыл бұрын
Love the Bauer DA buffer...always goes on sale. Probably a little higher than $49 now with inflation. The 6" pads are good quality too! 🍻
@joeshmo9152 Жыл бұрын
It's amazing the things you can accomplish on a tight budget using things from harbor freight. Just need to manage expectations and avoid anything safety critical
@kristofferhays3498 Жыл бұрын
Hey man I wanted to let you know I went out to buy two of the Harbor Freight clamps you reviewed. I have to say I 100% agree with your review, these are KILLER clamps and easy to use. Like you I also have a few different ones as many wood workers do but these clamps, I am super excited to have gotten. Thank you for reviewing these products, it was very helpful. What I did like about these clamps is not just the ease of use but how accurate the pressure felt on my cutting boards. I also have an idea for a video for you, granted I have not seen all of your videos yet; I would make one on Tool Maintenance and clean up. Like how to clean, sharpen saw blades, Maintenace on these claps and how to properly cover them etc. I am not seeing many videos on good tool maintenance such as blade sharpening, how much that can save vs building new ones, cleaning them etc. Thank you for your videos, this one was very helpful!
@tims1787Ай бұрын
I've used the Hercules job site table saw intermittently over the last 3 years. The fence can be finicky, but if you use a rule or tape to check the distance from the blade on both ends of the fence, once you lock it down it doesn't move easily. It's a decent, low-cost table saw,
@thomassciurba5323 Жыл бұрын
I bought the new Hercules planer with a 25% off coupon for $299. Hard to pass up. Bought a third grinder for $40 or so there simply so I did always have to be changing from cutting to grinding to flapper wheel. Works great, and has a good quality feel to it. I use a lot of their consumables like grinder disks, acid brushes, chip brushes, and rubber gloves. I also like their hardware kits for wing nuts, nylock nuts, springs and the like. You are right - those magnetic trays are great if you are like me always losing that critical screw. I also use them to organize hardware when I am doing a new assembly. Probably have a dozen of them in a few sizes. I use their analog vernier caliper every day which is precise enough for my needs. US General toolboxes are a great value, many of the mechanics where I used to work swore by them. The shorter (16” or so) F clamps and the spring clamps are well worth the money and you can never have enough. There is some junk there though, mostly Chicago Electric stuff and cutting or drilling bits and blades although for wood their drill bits seem OK. Overall I’m a Harbor Freight fan and am overjoyed they just opened a store 1 mile from me, right next to a Lowe’s.
@cheapme18506 ай бұрын
My drafting teacher in high school beat it into our heads that it’s a RULE…a ruler is someone who runs a country. This video brought back those memories.
@Ojja7811 ай бұрын
Another great tool at Harbor freight that I've used is the Chicago electric 10" tile/brick saw. Definitely not as good as other more expensive brands, but it's great to get started doing tile projects. I found the sliding trays to be a bit off, so you have to correct for that, but if you're careful and mindful you can work around it. I had to take the first one I got back because the tray was REALLY bad, but the second one I got was fine. Used that saw for several years as a contractor and did multiple bathrooms and kitchen backsplashes with it (I think I did 8 bathrooms and 5 kitchens) before upgrading and the finished projects were very good and precise.
@longsnapper53816 ай бұрын
Started my son off at HF as he just got his first house. Their tool totes, hand tools, hand truck,squares, etc are working well for us(him). I've got all my old high quality stuff from my dad (though 90% of my power tools are corded) and the HF stuff is acceptably close. He was a pretty decent wood worker in High School and wants to set up a shop in his garage. I'm sure he'll invest in better stuff when necessary but for right now HF fits the bill.
@tonylittle86348 күн бұрын
You give solid advice on something that’s real and tangible. I’m a plumber of 20 years and I’m very particular on the tools that are in my tool bag. Harbor freight has some 💎. You just have to do your due diligence.
@richardmclaugfhlin652 ай бұрын
I'm a sculptor, but over the years my back problems have been getting getting worse and worse, including one operation, so I bought one of Harbor Freights pickup cranes to mount on my welding table to lift heavy pieces. It worked fine for about two week and the hydraulic cylinder sprang a large leak. I called the customer service number with my heart in my mouth: this was, after all, Harbor Freight. I spoke with a very nice woman who, without giving me any runaround, send me a new cylinder, freight free. The new cylinder works find and I've been using it for over a year with no problems. I still by some stuff from Harbor Freight and most of it is adequate for my needs. Don't listen to haters OR fanboys. Make up your own mind.
@charleslong1284 Жыл бұрын
I have the Hercules random orbital sander and love it better than four other brands I have. I also love the LED 10,000 k shop lights. They are the best fixtures I have. I love the Yukon tool box so much I bought a second one. I use lots of their drill bits in small sizes. I just bought the new airless spray gun yesterday which compares to Graco. I will rate soon.