Hey mate 1st of all thanks for taking the time out to make this video. I fitted the side stand relocate today on my 2020 790R I didn't have to as you said take AXP skid plate off the wire to the sender was routed behind the countershaft sprocket with 2 locating screws for the special wire holder after removing the countershaft sprocket I had to cut the plastic swingarm protector slightly to remove both the wire holder with 2 small zip ties out once removed I re routed the wire up behind the cylinder on the back of the starter motor re zip tied the wiring with the quick shifter harness wires job done just sharing for those who bother to read the comments cheers Travis

Can see how this would be important for serious off roading. My DR650 has a clutch and kickstand switch that many bypass to avoid aggravation. Keep up the good work!

Good Review and install. I'm going with the Enduro Engineering skid plate, and going to try and fab the AXP so the wings protect the tank.

I had the side stand sensor fail on my 990 Superduke and on the 990 SMR. I carried the side stand eliminator. It plugged in to the connector near the side stand. So the switch does fail on its own from time to time. I like this idea, and will be getting one.

i am looking forward more 790 offroad madness ;)

Thanks for the vid. I’ll get one for sure, but I’m going to try and find a place to mount it not on the engine... even if I need to splice in some wire to make it longer. Mines decat’d so there’s gotta be room somewhere and not on an engine bolt. Again, thanks for the vid. 👍

If the bypass is mounted near the CAT would not the heat damage the switch?

We need to get you some more subscribers so you can get a proper bike lift. Keep up the great video's.

Ok, we've seen the video on installing this bypass but what oof the switch goes bad? You're still stranded unless you know a work around for the switch. Does anyone know the principle the switch runs on so we can bypass it if we need to? There has to be a bypass that fools the ECU.

good video. May I know how tall are you ?

How is the axp skid plate?

Good video! Travis have you had a problem with the side stand moving during off-road travel in whoops I've noticed my kickstand moves up and down. Do you have that problem?

I was with you until about 4 minutes in...I don't think I have a 10mm... when I got my set that one piece slot was empty. Tried to return it & every other set was the same way...

What did you do to Travis? Who is this impostor? Seriously though, does your skid plate provide protection after relocating it? It looks like it is pretty good in the other location.

is there one for the 1290?

But this bypass thing doesn’t work on the 2024 890r.

In the hope that you will even read this or respond to, here is what is being said by a KTM mechanic. Have you had any of these problems? From a Forum '' 790/890 issues and why do we still buy them?'' KTMs are what they are: incredibly well-engineered bikes that work amazingly…when they work. Some work longer than others. Despite a few niggles like airbox sealing, air filter access (fixed on the new design), and fuel pumps, that 1090/1190/1290 platform is a solid bike. I’d have no issues putting my money down on one. The 790/890 on the other hand is a pile of garbage. The list of problems I’ve seen on these bikes is a mile long and growing by the day. - premature valve wear - premature cam wear - immobilizer failures - brake failures - rear shock failures - countershaft seal failures - coolant leaks - clutch lubrication issues - TFT display failures - Fuel tank venting issues - Fuel pump issues - Debris in fuel tanks - Single-cylinder startup problem that still has no cure - Cold-start issues - Airbox sealing issues - Numerous software problems (MTC failures, intermittent cruise control failures, ABS failures) If you’re one of those guys who reads this post and says “I’ve had a 790 for XXXXX-thousand kms and have never had an issue” then good for you, count yourself lucky. After working on dozens of KTM P-Twin bikes that have come through my shop and speaking to the owners of many more, I can name only one that didn’t have at least two of the problems on that list. It’s a great piece of design that was utterly ruined by corporate structuring…built to a price, not to a spec. It’s still riding the wave of being the best reviewed bike (reviews where editors ride carefully-prepped bikes for one or two days then give them back) in what it arguably the hottest segment in motorcycling right now. Mark my words gentlemen…once that hype fades away, a few years go by, and reality sets in, the first-gen KTM P-Twin WILL be remembered as one of the all-time biggest lemons in motorcycling.

Africa twin life!!!!!!

wow, that's simplier than I though, and I don't like. Why not create an electric switch that would solve that? In the end it can't be too complicated what this magnetic switch is doing... And by relocating it we are only relocating the problem, not solving it.