@jack247811 - You're welcome!

@stevebeeler9103 - A good place to start with old chairs is to find out if the company that made it is still in business. If they are they should be able to answer your questions. Look to see if the chair(s) still has an ID tag ---> kzfaq.info/get/bejne/pt9ilbaByNuYYaM.html

Thanks for this reply too. 😊

@emilybradley3821 - When the parts you want are missing, that can be very difficult. I give some tips on mech spring replacement in this video ----> kzfaq.info/get/bejne/l9Vog9do1bHWdmg.html In the video I talk about looking for potential spring attachment points. Once you locate them, you can measure the distance between those points. The spring will have to be slightly shorter than that distance to avoid falling off, when the 2 points are closest together. And it will have to be able to expand (stretch) when the mechanism opens & closes. So, finding the distance where the 2 attachment points are furthest apart gives you an idea on how much stretch is required. But this doesn't even cover the style or type of spring that is needed! Like I said, this can be difficult. Here's a better way: Find an experienced repair tech that serviced Lane products in your area. They will be familiar with the springs on your chair & may even have some replacements left in stock.

@ramblingsFromJim - If it's a cheap recliner, it will likely have its flaws. Whether this is a flawed design or repair issue would have to be determined by a repair tech who is familiar with your product. Or a repair tech that has experience with working on many different recliner brands.

@thensr2011 - If your reclining mechanism is leaning -- as mentioned in the video -- this can create a bit of a sunken feeling when the seat is not level. Check for lean, as described in the video. But most often this issue is due to seat padding breaking in and/or breaking down. For example, if you tend to sit to one side of the seat -- like next to an arm -- the seat padding will break in the way it's used. So the padding next to the arm will break-in first, causing a dip or soft spot there. Cuts in the underside of the seat cushion is also common with recliners & can lead to the same issue. See this video to learn more -------> kzfaq.info/get/bejne/pr2keLV73ZvOmGQ.html

@ibrawring9525 - There are a few potential causes here. The mechanism may have some problems -- bent, loose, etc. -- or there may be an assist spring that has broken or come off that helps the back return to upright. Also, check for a problem where the back attaches to the seat. Remove the back & inspect the attachment point, the back brackets, etc.

@@reclinerrepairguy4155 Thanks! Will also reference your other videos to help with further inspection - these are so useful. Appreciate you making these.

@sandythompson5664 - Replacement parts are not likely be be more universal since I made that video. The biggest issue with overseas parts has to do with how many replacement parts are produced by the manufacturer and where (& how long) they are stocked. I would not be surprised if many manufacturers only provided parts that they currently produce for their current product lines. In other words, if you need a replacement reclining mechanism in 5 years, will it still be available? Maybe, if they're still producing that part. But if they've switched to a different mechanism, you may be out of luck. Also, if you have no parts coverage warranty from the manufacturer, no one from the company is obligated to help you with replacement parts. But then again, any furniture manufacturer could also go out of business, which would put you in a similar situation.

@HenriettaLong-fw1gy - You can lubricate pivot points & moving parts, but sometimes creaking noises come from other sources. See this video for lubricating pivot points ------> kzfaq.info/get/bejne/gdymo7V6s9Wpc30.html And this one for dealing with squeaks & creaks from other sources ------> kzfaq.info/get/bejne/bNlxhcV7usWsgY0.html

@vdub5975 - Actuator failures were not common, but I didn't work on a lot of different brands. The most common failure I'd see on La-z-boys was due to the customer continuing to use the motor (actuator) after something on the mechanism -- often a plastic part -- had failed. The resulting damage could bend or break other mech parts as well as the actuator arms that extends.

@sue3424 - The easiest way to do that is to simply disable the reclining mechanism. Then you have a stationary chair. If you have a 1-piece mechanism, the mech unit also serves as the legs, so removing it would put the chair seat on the floor.

@amandawaffle4894 - I recommend having an experienced repair tech check it out as there can be several causes for that type of problem. Here's a video with more tips on resolving your issue -------> kzfaq.info/get/bejne/aa2Ia66DuJjThok.html

Thank you so much ! I’m so glad I stumbled onto ur channel! U were the most easiest to understand and very knowledgeable!

@lastgameplay - Not a good idea. Instead, have an experienced repair tech check out your chair.

​@@reclinerrepairguy41556:27

@FoldedJay - That's typically how wallsavers work. The chair moves forward as you recline, allowing you to place the recliner closer to the wall.

@@reclinerrepairguy4155 but it seems broken or something or like it was fixed for it to be like that be the last owner . Like it goes down to the ground with the reclined leg rest touching the floor . Is there anything I can do ? Like tighten or loosen something underneath?

@@FoldedJay - Sounds like you need an experienced repair tech to look at it to diagnose the problem.