8 Tools Under $20 YOU Said to Buy
Рет қаралды 1,072,845
Жыл бұрын8 woodworking tools all under $20! Pick up these cool tools to help you with your DIY & woodworking projects.
Get a Maker Mountains T-shirt: fixthisbuildthat.com/product/...
🎥 What to Watch Next:
12 Tools Under $20 Every Woodworker Needs - • 12 Tools Under $20 Eve...
Mobile Wood Storage Cart - • This Easy Wood Rack Ch...
13 Shop Storage Tips - • 13 Easy Ways to Organi...
➤Plans from this video:
Modular Garage Cabinets bundle (Save 30%) - fixthisbuildthat.com/garageca...
Mobile Lumber Cart - fixthisbuildthat.com/mobilewo...
Drill Charging Station - fixthisbuildthat.com/drillsta...
➤Tools/Supplies Used (Amazon affiliate links):
Pentel Graph Gear 1000 - geni.us/qY5L
Pica Mechanical Pencil - geni.us/b0Xh8L
Pica White Lead - geni.us/rrq7
Stud Buddy - geni.us/rDXF
Olfa Utility Knife - geni.us/u60V
Snap Off Utility Knife - geni.us/a1gM
Tongue Depressors - geni.us/pUYR
Coffee Stirrers - geni.us/0v3uc9P
Drinking Straws - geni.us/8CC7
Kreg Multi-Mark - geni.us/o6tVB
Silicone Glue Trays - geni.us/OOoV
Glue Spreaders - geni.us/aTwtQf
Tire Depth Gauge - geni.us/vM1pquI
1-2-3 Blocks - geni.us/rZJXm
ISOtunes Bluetooth Hearing Protection - bit.ly/2Ru4Es8 (10% off code: FTBT)
➤Join the Builders Club!!! bit.ly/2abkaSV
More content, early access, FREE plans, video credits
Thanks to Woodcraft for sponsoring this video!
➤Support the FTBT Channel:
Buy FTBT Woodworking Plans: fixthisbuildthat.com/plans
Buy FTBT Merch: bit.ly/2YgiHnd
Links to My Tools & Gear: bit.ly/FTBT-tools
Subscribe: bit.ly/FTBT-youtube
➤Thank you to these partners for supporting my channel. Go check them out!
Kreg Tool: amzn.to/2FXZIGp
ISOtunes: bit.ly/2Ru4Es8 (10% off code: FTBT)
TimberlandPRO: bit.ly/2Zm1r1n
➤FOLLOW ME on Social Media:
Instagram - / fixthisbuildthat
Facebook - www. ibuildthat
Twitter - / fixthisbuildtht
Pinterest - / fixthisbuildtht
➤Referenced people/videos:
Music Licensed through Epidemic Sound - Get a FREE month: bit.ly/3qCwWiW
@Fixthisbuildthat Жыл бұрын
Get a Maker Mountains T-shirt: fixthisbuildthat.com/product/maker-mountains-navy-t-shirt/
@Environmenthrall Жыл бұрын
Better than the stud buddy, the CH Hanson magnetic stud finder, simply because it has a built-in level with the ability to rotate. Just under $10.
@kooogt Жыл бұрын
FYI, You don't even have to disassemble your stanley knife to get a new blade. push it all the way forward and the old blade will release and you can pull it out the front, then pull the slider all the way back to load a new blade.
@alaincohen7052 Жыл бұрын
See
@vvsandgaming4648 Жыл бұрын
In some countries it's actually illegal to have a knife of any kind, even if you are a trades person, that you can expose and hide the blade of with one hand.
@aserta Жыл бұрын
uni Kuru Toga 0.5 mm High Grade Auto Lead Rotation Mechanical Pencil The tip rotates, in order to keep a new face on the surface you're working on, thus kinda auto sharpens. Will admit, for working on wood... maybe doesn't work as well, but for draft work, best mechanical pencil that isn't a Rotring.
@rhkips Жыл бұрын
To be fair to the tire depth gauge, if you're needing 1/64" accuracy, you're not a woodworker, you're a cellulose machinist, and your projects can never leave the climate-controlled environment they're assembled in. ;)
@Fixthisbuildthat Жыл бұрын
😂 😂 True
@woodworkingandepoxy643 Жыл бұрын
Not completely true. Doing dove tails gaps are hideous and need a lot more accuracy than a picnic table
@woodworkingandepoxy643 Жыл бұрын
And wood that's dry enough for your region won't warp like construction lumber or pressure treated. As long as it has a good finish and not going into a home with no Insulation
@PhoenixRevealed Жыл бұрын
"cellulose machinist"... perfect... I'm gonna steal this.
@1steelcobra Жыл бұрын
@@woodworkingandepoxy643 Eh, a good router and jig were good enough for Norm on dovetails.
@EvanSamuels Жыл бұрын
You don’t need to take the wheel off to change the blade on the Olfa. Just loosen past where it catches on the body. At that’s how mine works.
@PhoenixRevealed Жыл бұрын
Yeah, changing blades on the Olfa is at least as fast as on the Stanley if you don't overcomplicate it by completely removing the knob and spring.
@DavZell Жыл бұрын
Came to say the same thing. Something to add, though, is that Olfa blades are known to be thicker/stronger, making them more useful for people that cut thicker materials like foam boards, insulation, etc. You essentially have a long disposable knife that holds up better than trying to do the same with regular snap off blades. The front support is also supposed to be helpful in supporting the blade as it flexes, letting it flex without breaking better than others, though I can't vouch for that.
@purroductscentral Жыл бұрын
Haha, I was coming here to say that too, as someone who uses one almost daily. And I bought a diamond sharpening pad which I use to resharpen the blades while they're still installed, because I'm cheap AF.
@KingMidas1983 Жыл бұрын
@@DavZell Olfa also has the black "high carbon" blades that last a lot longer
@kellendil Жыл бұрын
Also, as a parent of two small children, i really like that I can properly lock the blade :)
@AnthonyRose Жыл бұрын
I spit my drink when you fired that shot at Lowe’s 😂
@tomfinn739 Жыл бұрын
For mixing up just a little bit of epoxy, the best thing I've found is something you had in the video. Just flip a Dew can upside down and use the bottom.
@buckyV Жыл бұрын
I’m surprised nobody has mentioned a 5-in-1 painters tool yet. As a carpenter, that’s one of my most used tools! Great for scraping, prying, chiseling, or, y’know, painter things too probably
@whasian1487 Жыл бұрын
mine also has a bottle opener as well. great tool
@Trevin_Taylor Жыл бұрын
Agree
@GeeDeeBird Жыл бұрын
Yup. Very handy.
@jimmiefitzgerald4961 Жыл бұрын
@@whasian1487 well now that is a 6-in-1
@simeongray2645 11 ай бұрын
He actually had one in his previous video
@billbender6926 Жыл бұрын
The best feature about the Pentel pencil is that when you retract the tip and then re-extend it, the lead stays at the previous position so you don’t have to click until you get it where you were using it before. This might seem trivial, but it’s great if you are holding something and don’t want to look away to set the lead extension to where it’s usable.
@woodstream6137 Жыл бұрын
Nice. I used pencils in school but don't need them now. I like the idea of protecting the tip from bending which has happened more than stabbing myself that one time
@dubmob151 Жыл бұрын
While it appears to be a very rugged metal bodied construction, you do need to take care not to drop it to the floor because the middle joint is plastic and can fracture. My favorite part of the design is the clip, which allows it to accommodate thick pocket material easily and holds securely. Retraction mechanism has a nice solid click that serves as a fidget toy to boot 🙃
@dubmob151 Жыл бұрын
@@thealchemist5376 what does the replacement collar do?
@thealchemist5376 Жыл бұрын
@@dubmob151 It replaces the plastic collar (the part under the grip and which connects to the main body) with an aluminium one, or whichever material you want. Much more sturdy!
@dubmob151 Жыл бұрын
@@thealchemist5376 that's just the ticket for making it perfect 👍
@randallthomas5207 Жыл бұрын
I use a “cow magnet” to find screws and nails in drywall. They are 1/2-inch diameter and 3-inches long, rare earth magnets. They put them in cows stomachs to keep nails and bits of fence from coming up with their cud.
@karenr8805 Жыл бұрын
One of my favourites is a combo of dollar store craft foam and double- sided tape. Use the tape to stick sandpaper to the foam - I typically cut them approx 2" × 3" unless for something specific. These are great for sanding small or tight areas where you would probably otherwise just grab a scrap of sandpaper and try to fold it to give it some substance, only to have the paper getting frustratingly crumbled before the grit or job is done. This way is easier to grip, flex into and around spaces, and lasts longer. You can also use a permanent marker to write the grit on the foam.
@MrSpeakerCone Жыл бұрын
One underrated tool in the wood shop is a handfull of lego bricks. They make great little spacers and they're accurate to some crazy tolerances given they're pennies per brick. Like the world's cheapest gauge blocks. Also a deck of playing cards makes excellent shim stock.
@Fusilier0 Жыл бұрын
Someone above suggested using a silicone baking mat for under glue ups. They’re also great for under a hot glue gun, not just wet liquid glue. Also I purchased a number of cheap silicone basting /BBQ brushes at the local dollar store and then trimmed the bristles down to about 1/4” or do (50 or 60 mm) long to make great stiff glue spreaders. Again dried glue comes off. On the same vein I’ve saw an Australian woodworker’s KZfaq channel where he used a cheap silicone cooling spatula for spreading glue on even wider parts. Oh and did I mention that dried glue comes off way. I even use individual silicone muffin cups for mixing 2 part export. And you can guess what happens to dried epoxy …
@bobcouncil8205 Жыл бұрын
Being a retired Tool and Die maker I used 1 2 3 blocks a lot in making dies so I dragged my blocks out and started using them for woodworking as a hobby. They do come in fairly handy in fact I use quite a few of my Tool and Die tools such as squares and measuring tools. But my woodworking skills aren't nearly as good as my machining skills were. Keep up the great videos.
@steves7345 Жыл бұрын
I worked in a tire shop for years but the good tread gauges don't use stickers they are actually marked on the shaft not saying they are more accurate but they won't peel off
@Fixthisbuildthat Жыл бұрын
Yeah, those were obviously the absolute bottom of the barrel
@luke8952 Жыл бұрын
You can get Olfa knives with the button instead of the dial if that's what you prefer. You also don't take the dial off to change the blade, you just back it off enough for it to clear the stop.
@Fixthisbuildthat Жыл бұрын
😂 😂 That makes a lot more sense
@GeorgeDeery Жыл бұрын
Yes they have multiple styles and sizes. The biggest advantage I feel is that Olfa is made of fiberglass and not plastic. I've dropped mine numerous times and it's tough as S.
@gregwoollacott2618 Жыл бұрын
I liked the straw approach to dealing with glue in tight places. Straws and other single use plastics are being banned in many jurisdictions. Suggest DIY'ers consider using the V-notch tool that comes with silicone placement and removal kits. This tool is reusable and will help to keep plastics out of landfills and the environment.
@MrMega200 Жыл бұрын
Indeed I'd rather wet a paper towel and toss it after I couldn't get anymore use. At least that won't take 500 years to biodegrade. The other problem with these single use plastics is that they become part of our beaches as plastic shards and pebbles. What he should really be buying is paper straws if he wants something disposable. You can buy 200 packs for about $7. Or a 600 pack(Kingseal brand on Amazon) for $10.
@anthonymarker4984 Жыл бұрын
Totally agree with the issue of single-use plastics. That said, straws are handy since when you've got a glue-up with clamps, straws will allow you to come in from the side(s) in tight spaces to get the glue before it sets. Nick's idea of paper straws might work but I haven't tried it.
@path4061 Жыл бұрын
Saw one video where someone bundled straws together and put them in the end of their shop vac hose. With this, they vacuumed out wood chips that were in their small parts tray without worry of sucking up any screws, nuts or washers.
@twilli7 Жыл бұрын
Best idea of the year. 1-2-3 block in nominal lumber sizes. Brilliant.
@Rodbuilder109 Жыл бұрын
Stumpy Nubs has a video on the 1-2-3 blocks very informative and he worked with Taylor Tools to make hardware for them as well.
@davet7509 Жыл бұрын
One of my favorite oddball cheap tools is a hemostat. Cheap ones from the cheapo tool store are like $7, but usually have a sloppy pivot and the jaws don't line up well. Spend a few bucks more on a well made pair and the are the best needle nose pliers.
@kevinhilton8683 Жыл бұрын
I think what you really want more than a hemostat are surgical needle holders. They are far sturdier and have a better grip.
@cottrelr Жыл бұрын
If you happen to have a DeWalt 20V trim router, the radius of the fixed base is exactly 2" from the center of the bit. So a set of 1-2-3 blocks works perfectly for setting up an edge guide for dados.
@richthomas5013 Жыл бұрын
Great tip. I didn’t know that. I keep a 123 block at the table saw with one of those Rockler hook clamps. I drop it over the fence for an exact 1” offset when I’m using my miter gauge.
@Fixthisbuildthat Жыл бұрын
Nice tip!
@michaeldequatro1012 Жыл бұрын
Right after your video, I found a Woodcraft store about 15 minutes from my house (I must have passed by it 100 times). What a great store. I'm glad I saw your video.
@erickdanielsson6710 Жыл бұрын
I use WoodRiver Silicone Glue Roller 12.99 at the Franklin Woodcraft, Yes it's my Woodcraft store. Nice folks there. I glue several wide pieces together, spreads glue quickly and evenly. Easy to clean too. Thanks Brad, I hope to meet you at the Woodcraft one day.
@labsquadmedia176 Жыл бұрын
Straw/Glue Tip: If you wait for the glue to slightly dry to a putty consistency, the straws work even better!
@michaelobrien4259 Жыл бұрын
Can't buy plastic straws in Australia - not environmentally friendly!! Sheesh, as if that is going to save the world.
@NorthVanDukeOfDirt Жыл бұрын
@@michaelobrien4259 Same thing in Canada. Only paper straws now.
@NeoRichardBlake Жыл бұрын
@@NorthVanDukeOfDirt I was coming too look for/leave this kind of comment. I didn't want to be that guy either, as I use straws all the time (I don't like single use plastics and try to wash/reuse what I can), but I'd like to know if paper straws would work as well in this application. Now that I think about it, one straw could probably be used for this many times though. After use, just cut off the used tip and throw out. Probably only really uses about a 1/4 in of the straw with each use.
@GeeDeeBird Жыл бұрын
I didn't think I had a suggestion, but it turns out I do! You - and many of us - use the little Dixie cups for mixing and pouring small quantities of glue or paint or whatever. But, when you need to mix a small amount of epoxy, you simply cannot beat a plastic spoon. Used in conjunction with a toothpick (or one of those coffee stirrers, the bowl provides the perfect shape for mixing and encouraging the catalytic action. Grab one out of the back of your utensil drawer (from the last time you got take-out) and give it a try!
@stuartgray5877 Жыл бұрын
I have had MANY "Stud finders" in my life. Recently I have just started using three small RE magnets. Find three screws and find the "best fit" plumb line that aligns with the three magnets and you know you have a stud.
@alancharbonneau4108 Жыл бұрын
My dad was a machinist. He would have found it amusing that the 1-2-3 block sold on Amazon are machined to a tolerance of one thousandth of an inch on each surface, but of the 15 holes though which you are supposed to be able to pass a bolt, most are the wrong size. An Amazon review reads “the unthreaded holes are too small diameter to clear the threaded fastener that would go into the threaded hole in the adjacent block. Hence making them useless as an assembly” I think that is hysterical. I have two of these and don’t need to worry about making assemblies since I am a woodworker, but the holes being the wrong size is something I find more than amusing.
@marcbarash6045 Жыл бұрын
The Kreg marking tool also has a recess that enables you to space door trim around a frame.
@Fixthisbuildthat Жыл бұрын
Oh, nice little hidden feature!
@bitbyte98 Жыл бұрын
That is a great feature!
@davefink2326 Жыл бұрын
The studbuddy has advantages: it's big and colorful so you can find it. Its strong magnet has a cover so it won't stick to other tools in the toolbox.
@musicalmcbride Жыл бұрын
Glue bottles! The Glubot (made by fast cap) is a total game changer. I also like the Rockler glue bottle that has a roller built into the lid. The glue dispenses directly onto the roller, so it's really easy to spread around.
@game7win596 Жыл бұрын
The 123 blocks are a tool you never knew you needed until you get them! Love them lol
@stephenmerkel7402 Жыл бұрын
I used 1-2-3 blocks all the time to run a CNC router table. They work great with T nuts in aluminum extrusion as backstops and clamps, and you can also make your workholding clamps much sturdier if you use the 123 in place of a long bolt for clamping down thicker pieces. I was carving vacuum form mold bucks to make automotive trim pieces at an armored car factory, and they are also great as a quick way to offset a measurement, so maybe you are using a stack of gauge blocks to build up your 3/4", but then you need 1 3/4, you can plunk the block in and quickly extend your measure, set your fence, and it saves you time(at that plant we had a machine shop as well as the wood shop, so I milled myself a pair of "nominal lumber" 1-2-3s as well for dealing with 2x4s and the like, too, and you are right, that is pretty handy in a wood shop, but I also had a laser there I used to make all sorts of nice metal woodworking jigs out of armor scraps).
@briansharp4388 Жыл бұрын
I'm an old machinist, love my 123 blocks...use on mill, drill press, lathe, surface plate set ups.....
@lauramarshall6376 Жыл бұрын
Just a suggestion. To spread glue on larger surfaces, I use cards - hotel key cards, cruise cards, old membership cards, etc. You can also use expired credit cards, but be sure to put them up or shred before tossing. They are easy, free, and work great. And they also clean up easily if you want to reuse them. Great video. I'll be buying few of those goodies.
@Earendilgrey Жыл бұрын
We use 1 2 3 blocks a lot in prop/costumes making. They are great for everything, even down to using them as pattern weights when you are tracing out your patterns.
@mistercof Жыл бұрын
I use a kitchen rubber spatula as a glue spreader. It's great on edges or flat surfaces. You don't need to wash it, just let the glue dry, it'll get off easily
@GeeDeeBird Жыл бұрын
The silicone ones are even better.
@WoodworkingDaddy Жыл бұрын
Great info on the tools. Also, I'm not gonna lie, I'll be *so* glad when the fad of inserting movie clips into KZfaq videos has ended.
@Fixthisbuildthat Жыл бұрын
😂 😂 I can see it fading in time. But I still find it fun to rehash old movies I loved
@sethers18 Жыл бұрын
One tool accessory that I love for spray painting is the Rust Oleum "High Performance Comfort Spray Grip Accessory". Last I checked, it's about $11.50 at Home Depot and makes spray painting anything so much easier!
@across8339 Жыл бұрын
I have had the Olfa for over 20 years and still going strong. Can't beat it.
@mccarseat Жыл бұрын
Great video, as a machinist I used 1-2-3 blocks at work at all the time. Then when I started working on my house and doing other projects, i found them very useful around the house as well. I've been legitimately surprised at the quality or some of the ones i've bought for cheap online. They aren't quite as good as ones i've made or high end ones i've bought, but I don't need them to be within .0001" for house projects.
@Fixthisbuildthat Жыл бұрын
Yes, agreed. I was pleseantly surprised by the squareness
@rpavlik1 Жыл бұрын
I've never been a machinist but I bought 123 blocks and they have been handy in some unexpected ways. Also makes a reasonable guide for drilling square.
@justinnovak1275 Жыл бұрын
I found myself using 123 blocks as paper weights in my shop for when plans wanted to roll themselves up. So my son, who uses mostly exocit wood in his work made me some 123 blocks out of some purple heart and Lignum vite. Not particularly accurate but nice to have and better to use as paper weights.
@raidzeromatt Жыл бұрын
Yeah I didn't know people used them outside of machining 3-2-1 blocks are machined within hundreds, thousandths, or ten thousandths of an inch so that you can set your tool offsets when using a CNC machine or just making sure you have your tool set up properly if you have a regular end mill Just make sure to remove it from the table after using it lol I've seen people crash machines from leaving one in a machine before they ran it They're not really made for woodworking, so unless you're using it for something like setting up a planer or router table you're probably better off using a scrap piece of wood
@rpavlik1 Жыл бұрын
@@raidzeromatt I think you missed the point, they have many uses outside machining.
@andrewbieger5004 Жыл бұрын
I have, I believe that exact Olfal knife. You do NOT need to completely unscrew the bits from under the wheel to remove the blade stub for replacement. Once the wheel is loose enough, it just slides out the back and you hook on another blade.
@doctorWHO_ey Жыл бұрын
A case of operator error. The olfa is simply better.
@DavidPowell Жыл бұрын
The pencil is a drafting pencil. The metal tip, one, supports the lead to help prevent easy breaking and so you don't get lead on your drafting rulers and other tools since those tools are typically slightly elevated from the surface of the paper.
@frigginpos Жыл бұрын
1-2-3 blocks are awesome. The .75-1.5-2.5 blocks would be FANTASTICK!
@garfieldnate 7 ай бұрын
Just want to say thank you for running an extremely relevant sponsored segment (rather than garbage I needed to fast-forward through). A really cool-looking store I've never heard of with lots of pictures of the inside and some fun/cheap/useful products they have there. It was perfect.
@FrankTranDesign Жыл бұрын
Regarding Olfa. I only use 2 types: For Heavy Duty, the LA-X model -- NOT the one with the spinning dial. The LA-X model has the prying end that has SO many practical uses. To change the blade: try this instead: 1. Retract down to the last blade 2. If you're facing the dial (the front face), flip it so the 'back face' is pointed in the upward direction 3. Grab a piece of tape and put it on the last blade and a little onto the olfa knife 4. Push the blade downward; you should hear a confirming 'snap' sound 5. Properly dispose of your old blade For my lighter duty needs: The Olfa XA-1 is the other one I use (9mm version)
@Thanatas11 Жыл бұрын
123 blocks are great for offset blocks for doing cross cuts on the table saw. Know that you just are losing one inch when you setup the fence (so add one inch to the fence setting) and that way you can safely use the fence + block, remove block and then cross cut with a miter guide. I also use them for setting up on chop saws as an off set block against my stop block.
@The_real_dylan Жыл бұрын
That Kreg multi tool also has two sized lips along the edges for doing door casing. Works great.
@stevenkopec5266 Жыл бұрын
I love the Kreg Multi Mark for fastening casing around doors and windows. I don't think you mentioned that there is 3/16" reveal on the back of the Kreg Tool. Simply register the tool against the door/window jamb and then place the casing against the tool and you will get perfect reveals on all sides.
@getsum697 Жыл бұрын
Lived in Japan for a long time, where the Olfa knifes are made, I asked my wife to buy a bunch of them the last time she went back and visited. The knife you demonstrated was the cheap one, they make much higher quality knives with a paint can opener on one end, blade storage inside and the locking blade. The blade lock does NOT have to come apart, just loosen it and it will slide out with the blade. I couldn't respectfully disagree with you more about the blade lock, many a time I would be doing a draw cut on material with a non-locking blade and it would get caught in the material and pull the rest of the blade out or snap it off which wastes the blade. The lock stops both from happening and also keeps me from getting cut. To each their own though, some of us are just more right than others...🙂Good video though and great content!
@ZacharyKeithQ Жыл бұрын
I use the 1-2-3 blocks almost every time I'm in my shop. They're great for through crosscuts, where you want to use the fence to set up your measurement, but you can't keep the fence in place. You can use these as a block between the fence and your workpiece and you can easily add the 1, 2, or 3" to your measurement on the fence measurement. They're great for making sure the blade is square, for setting up a square saw cut with a pull saw (use a card between the block and the saw), or for making sure that the fence is set properly. They're also great for quickly helping make sure that a drill bit is going in straight. Keep them handy and see if you reach for them in the future.
@ipick4fun27 Жыл бұрын
I heard that the best 1-2-3 block for that purpose is the solid one. It's heavier and don't have holes for the wood to catch. I would've bought one if sell them as single. You really need 1 of them.
@watermain48 Жыл бұрын
It's probably just because I work at a Woodcraft store and know what is available, but the roller that goes with the tray is fantastic for spreading woodglue and puts a perfect layer down. Great video Brad, thanks.
@auntiedotal Жыл бұрын
You had me at that coffee stirrer from lowes! 🤣🤣🤣
@MORGANSMaintenance Жыл бұрын
The Pentel GRAPHGEAR is my go to with the .7 I love the weight of those pencils and the safety keeps it from poking your pocket. Thanks for the videos 👍
@watcherofwatchers Жыл бұрын
For snapoff utility knives, I really like the NT Cutter. It doesn't have a locking knob (like your Stanley), and it fits my hand really nice. The locking mechanism on my 5 or 6 different NT Cutters (I have them everywhere in the shop, garage, and house) has never failed. I like it much more than the Stanley one I used to love. Oh, and they're like $8.
@mlhse111 Жыл бұрын
Literally have had my greg multi-mark forever and didnt realize you had a slot on the back for the 45 degree angle. So much for reading the instructions i guess. Thanks. lol
@chaosordeal294 Жыл бұрын
I can't even use a stud finder. Love it when people mention "colors," then give a few examples for anyone who is having trouble following along. Like green or blue.
@paulapart5110 Жыл бұрын
Olfa blades are wonderful but you've got to try the version with the auto-lock instead of the tedious twist-lock version. I suggest the autolock model with the multi-pick feature, it is super handy for scoring cardboard and other jobs that require a thick dull edge. I've worked as an art handler for 10 years and that Olfa is my go to knife.
@redslover5293 Жыл бұрын
Great video. Been watching you for about a year now and you never fail to deliver. Also, saw your video on "6 Ways to Reduce Planer Snipe" and almost didn't recognize you, but you were delivering great info back then as well. Thanks, Red
@breezy_4679 Жыл бұрын
I use this gem when drilling out drawer and door fronts of cabinets to make sure the handles/knobs are straight. Can be used to sort out your coffee can of drill bits if it's not etched on the drill itself. It's called the Handheld Drill guide(Milescraft specifically due to rubber footings for non-slip). It's cost is around ~$8. I use this on a daily. Awesome videos. Adding more to my collection after every video. Thank you.
@Grpyphon Жыл бұрын
I also really like the mechanism for extending the blade of the Stanley vs the Olfa. Also, those blades are super easy to sharpen, you should hardly ever have to replace them. Between your other video and this one I'm definitely making a great list of things I need.
@Absoluteunit Жыл бұрын
You sharpen them ? Lmao
@DKC0994 Жыл бұрын
Kudos to the way you've merged your sponsor in here. One of the only sponsor breaks i didnt skip so far and i know youtoube from its beginnings
@paulboatwright8609 Жыл бұрын
Wooden manicure sticks work well for getting into tight glue joints. They have 2 different angled ends and have come in handy multiple times in my shop. $5 for 100 on Amazon.
@LiqdPT Жыл бұрын
1:35 the Graph Gear pencil is available in different lead sizes (each are a different color grips on the pencil, so easy to identify)
@orazha Жыл бұрын
The 1-2-3 blocks are also useful to check the accuracy of your weight scale.
@tomlilly Жыл бұрын
I bought a set of two. I have one on my bench. I also glued a magnet to my table saw and the other one lives there.
@NoobPWN3R666 Жыл бұрын
The real benefit with the olfa knife is when using hook blades, holds the blade in place better and prevents it from pulling out when cutting. Also you don't need to completely unscrew and disassemble the blade holder to slide it out the back. I use these all day every day roofing and after trying a dozen other knifes the olfa is still best all around.
@bitbyte98 Жыл бұрын
Great video Brad! The $5 glue bin is awesome. Reuse is key. No more waste! Awesome! My partner creates jewelry, this will be a lifesaver!
@robertquiles7815 Жыл бұрын
Hello Brad, I was wondering if you would mix the two worlds and 3D print the set up block you mentioned. It's able to be scaled to 3/4'" x 1 1/2" x 2 1/2" and can be easily reprinted if damaged.
@djsting Жыл бұрын
I use Eanosic (from amazon) setup blocks in conjunction with my 1-2-3 blocks. They come in fractional sizes. So you can use them with the 1-2-3 block to get those 1.5, 2.5, etc size measurements.
@gotdangelectric5599 Жыл бұрын
As far as the olfa goes, we use those all day at work and olfa is my preferred brand for sure. Way more durable than anything else we’ve tried
@c50ge Жыл бұрын
Pics is my favorite pencil. I carry it daily, even to Church on Sunday!
@pdxgigi720 Жыл бұрын
I have all those suggestion in my shop with the exception of the stud finder. I use the blocks for quick blade set ups more than anything. I've also used it on my router table. I have the pentels deliverd via survive and save. The clip that draws the led back works perfectly if you wear a shop apron because when you press it to clip it in you are automatically drawing in your led. Edited to add my suggestion: the fastcap lefty/righty 16 foot tape measure is the perfect size to keep in the shop and on your person.
@Trevin_Taylor Жыл бұрын
I agree 25 or 30 is just too bulky.
@RonMarshallrone Жыл бұрын
I have about 10 3-2-1 blocks and 95% of projects I make and sell I used them. So many uses. Been using the straws for glue clean up for 10 years. Works great.
@Fixthisbuildthat Жыл бұрын
What's your favorite use for the 1-2-3?
@JasonPeltier Жыл бұрын
@@Fixthisbuildthat I designed a 24" square planter. The top cap has a 1" overhang. The 1-2-3 blocks help me center the top piece onto the main frame quickly.
@RonMarshallrone Жыл бұрын
@@Fixthisbuildthat I make a lot of smalls and use them to check for square, I've used them with clamps to hold vertical boards to get in tight spots I couldn't use normal clamps or the Kreg pocket hole clamps for screwing in pocket holes, I use them for table saw and bandsaw alignment, clamp them to the TS fence for stop and start blocks that you know you will 1-2-3 inches for whatever you're cutting, I use 4 of them stacked to tram my CNC machine when I put a new spoil board on, I'll use them to help me nail or screw boards with seams that I need perfectly lined up ect...and a ton of other things. I hadn't watched the full video yea when I commented but you showed one the most used tools I use since 2010 with that Kreg Multi-Mark measuring tool. I use that in every project as well. Really good vid of simple tools that have crazy amounts of uses.
@dysartes Жыл бұрын
@@Fixthisbuildthat - I'm not a woodworker, but I could see using 2 sets when making drawers. Pop one in each corner to check for square.
@dinacusic7829 Жыл бұрын
I've used my set of 1-2-3 blocks for things from tramming my CNC for squareness to setting my table saw blade square with the table. They're surprisingly handy!
@williamellis8993 Жыл бұрын
Good info, Brad. I'm glad you liked the Multi Mark. See you next video. Bill
@realpdm Жыл бұрын
I can't remember who it was (I thought it was you but apparently not) but they used heart shape novelty straws from amazon to get clue out. The shape was perfect for getting glue out of corners. Fast food places are always giving me too many straws so I've never had to buy any so far even while using this trick.
@toddeyster7557 Жыл бұрын
I have been using a Graph Gear 500 in .9 lead size as a construction pencil for years. The .9 is quite a bit sturdier and will hold up to writing across grain etc. It also shows up on metal pretty well and does not get ruined by grease, oil, etc. I may have to check out one of those 1000 models for the other features, the 500 has a bit of a pointy end.
@kylekinsey2624 Жыл бұрын
I have had both and the 1000 is significantly better
@toddeyster7557 Жыл бұрын
@@kylekinsey2624 Just received my order from Jet Pens. Yes the 1000 is worth the extra money. That is a bomber writing instrument. I use it with HB lead and can write on about anything including glass.
@AzraelThanatos Жыл бұрын
With the 123 Blocks, they're also very good at keeping things positioned due to the weight and in maintaining a 90 degree angle or a full corner
@harrycoglionekwah-lee-yone6095 Жыл бұрын
Great job with the Seinfeld "shrinkage" transition. I like the way the music/audio stretched out back into your workshop video. Good transition bro.
@rogerlove7588 Жыл бұрын
I’ve had three of those .5mm pencils. Just wait until you drop it. Yeah, the tip might be protected, but the lead isn’t. It breaks into several pieces, which you then need to dig out. PITA. I love its design, it feels good in my hand, and it draws beautiful lines on wood. Then I drop it, and hate it. Maybe I should install carpet my garage.
@nachocheez9 Жыл бұрын
They make that Graph Gear pen in 0.9mm also. Maybe even something bigger. I have it in 0.9mm.
@mattmilner5935 Жыл бұрын
The Graph Gear pencil comes in other lead sizes, all the way up to .9, just FYI. I think .7 is a pretty good happy medium for bolder lines that don't snap the lead easily while also being precise.
@jefffree6990 Жыл бұрын
The Graph Gear looks cool. I use the old style yellow pentel .9 for cutting wood and DIY projects. the extra strength is perfect and is still fine enough. Maybe I'll upgrade
@christianhelms6676 Жыл бұрын
Brad, you'd be proud of me. Finally bit the bullet and bought a sawstop. Just the 3hp cabinet saw, but i love it
@Fixthisbuildthat Жыл бұрын
Your fingers and hands are more proud of you 😀👍
@wiseguy8828 9 ай бұрын
I have that stud finder it’s a life saver especially in older homes.
@240WoodShop Жыл бұрын
The cabinet installers I hired used that “Stud Buddy” and the guy drilled a hole right through a waterline Messing up all the drywall work I did. 😡
@benchapman5247 Жыл бұрын
I prefer the Tajima to the Olfa, similar 25mm/1" blades, also with a screw but can loosen and tighten to move just with thumb movement and no little spring clip. I also love the carbide edged blades and Tajima make saw blades for them too which are super useful.
@HAAVARDCHRI Жыл бұрын
You can just remove the spring on the Olfa and use it the same way. Faster and more convenient to just use the thumb👍
@roysnider3456 4 ай бұрын
I bought my 1-2-3 block when I was working as a CNC machine operator but I use them in the wood shop all the time.
@JeffPalk Жыл бұрын
6:16 "they got these from Lowe's" 🤣 100% accurate
@elliothickle3247 Жыл бұрын
If you like the Pentel graphgear 1000 the rOtring 800 retractable mechanical pencil is on another level! It's the best feeling pencil with a nice solid metal weight and great for fidgeting with the coolest opening mechanism thanks to German engineering.
@marsrevolutionary Жыл бұрын
The Pentel Orenz PP505 (second favorite after the GG1000) is not as sturdy or well-engineered but the sleeve retracts while you're writing, making it great for marking fine, accurate, long lines. I use the Orenz (0.5 mm HB) exclusively for fine marking and keep it with my Incra rules and use the GG1000 (0.5 mm HB) as my writing pencil. For lumber/inaccurate marking, I use a Staedtler Mars 780 (2mm 2H).
@GeeDeeBird Жыл бұрын
I use a pentel draftsman "lead holder." I have four of them in different colors for different contrast on material. They have a sharpener in the cap, which is very nice.
@integrax5559 8 ай бұрын
Those rubber jar opener things for your kitchen - stick um in your vices to get better surface area grip on odd shapes and smooth items - like glass that you can't tighten down hard on. Also their intended function is helpful when you got graphite, oil, grease, etc on your hands already. So handy in the garage too!
@drhender6943 Жыл бұрын
They make the Pica mechanical pencil in 0.3, 0.4, 0.5, 0.7, and 0.9. While I like the thinner 3/4/5 sizes for drawing, I find the 7/9 better suited for marking lumber in the shop.
@papaacorn9479 Жыл бұрын
1-2-3 blocks are super cool. But I prefer 2-3-1 blocks. They’re 2” wide, 3 inches thick, and 1” tall. They cost about $30 more, but I think it’s worth it. 😂
@Fixthisbuildthat Жыл бұрын
Maybe s 1-3-2 block?? 😂😂
@charlesenfield2192 Жыл бұрын
I'm with you on the Olfa knife. It's more complicated than necessary and there's no on-board blade storage. I got used to keeping my thumb on the blade retractor, and almost never have a problem with the blade moving no matter what knife I use.. That said, the Olfa blades are phenomenal. They stay sharp much longer than others I've tried. I know they cost twice as much as some other name brands, but in my experience they last at least twice as long. I also keep a 1-2-3 block at my table saw, and I use it as a stop with my mitre gauge. The beauty of it is I can easily choose how much extra space to leave between the blade and fence depending on the size of the off-cuts. I use one inch most of the time because it's nearly impossible to mess up the math, but I can switch to 3" if I need to.
@frankguning4133 Ай бұрын
I use a cattle magnet . It's capsule shaped . About 3 inches long . You can find them at a feed store (farming) . They use them to get metal fragments out of cattle . Grossly speaking , they are used as a suppository. You get a wire cap and drill a hole through the top of cap , and thread a string of twine through it . And then use tape to fasten the cap to the end of the magnet . When held like a plumb Bob, it will roll to the center of a nail , screw or edge of a metal stud .
@chalion8399 Жыл бұрын
Thanks for making this video. The Kreg Multi-Mark and the Pica mechanical pencil are just what I could use together.
@jimmydunn4707 Жыл бұрын
As an engineer myself, I agree, you can never have enough cool mechanical pencils! The graphgear 1000 that you showed does come in .7 and .9 leads as well. I ended up getting the graphgear 500 with .9 lead because it was just as cool, about half the price, and came in a much nicer silver than the yellow of the .9 1000. The 500 did not, however, have the special safety retractable tip :(
@halsti99 Жыл бұрын
i really like the incra tiny t for marking joinery. its nice, accurate, has very fine markings and only runs around 20 bucks.
@chadhowell1328 Жыл бұрын
The tiny T will make use of that .5 pentel mechanical pencil for sure!
@davidbondi Жыл бұрын
Tiny-T Rocks!!
@rosecitywoodworksllc Жыл бұрын
1-2-3 Blocks are for calibrating/checking your tape measures etc... The are machined to exactly 1" 2" and 3" and not only as a woodworker but also a machinist these things are invaluable to me I probably have 12 floating around the shop and if you ever drop one on concrete might as well trash it cause a ding ruins their calibrations
@MsRmaclaren 11 ай бұрын
I use automotive Bondo spreaders for larger glue ups and I have had them for 50 years and still going strong. I always have lots of various plastic lids coming through and I use those for glue ups and if I wasn't lazy the glue pops off but I just toss them when done (I have 50 on hand at the moment), we go through a lot of cottage cheese and the containers make good paint/finish mixing containers. Popsicle sticks from the dollar store for epoxy glue and toss when done. For furniture restoration I use a long artist paint brush with the hide glue and clean it with a little dish soap and water. I use a antique tire gauge as well.
@MCsCreations Жыл бұрын
Excellent tips, Brad! Really great tools! 😃 About the 1-2-3 blocks... I've been searching for them in stainless steel or aluminum, because here steel rusts faster than me when I hear that the launch is ready. 😬 So... You could make them out of wood! Any size you want and you don't even need the holes. That's what I'm going to do. 😊 Anyway, stay safe there with your family! 🖖😊
@Fixthisbuildthat Жыл бұрын
That's an interesting idea! Bet some Ipe ones would be stout
@MCsCreations Жыл бұрын
@@Fixthisbuildthat Exactly! Then all you need is to mark them with the measurements. Laser would work great for that, but even a sharpie can do. 😉
@koconnor Жыл бұрын
@@MCsCreations I have the same problem with rust here. I'm in Panama, hot and humid. Oh and let's not forget to say hello.
@MCsCreations Жыл бұрын
@@koconnor Hello there! 😊 But yeah, I'm from Brazil. It doesn't get any better here, specially because the beach is 3 blocks from here. 😕
@5280Woodworking Жыл бұрын
Great tools. The straw thing annoys me though. I hate recommending wasting plastic for the landfill to clean a little glue that a bio-degradable rag and water can do. I just think we need to be more responsible with our consumables IMHO. Maybe a paper straw works just as well?
@bhough410 Жыл бұрын
What's wrong with plastic sitting in a landfill?
@Ajyn4Life 10 ай бұрын
Get the biodegradable straws.
@panfull Жыл бұрын
bare with me here. A simple plastic sleeve folder. I do my plans on sketchup, a cut list on the side. print it. and add it to the folder. dust doesn't get in and it keeps water out.
@AnctilPickup Жыл бұрын
I have that exact same combination square tool and it actually belonged to my grand father before, he gave it to me and i use it alot now!
@dawsie Жыл бұрын
WOW the fact you can still buy plastic straws in the States, they have been band in Australia can only find paper straws here. I have not seen plastic straws since last November now when I bought all of the ones from our local supermarket 😹😹😹 always used them for cleaning up glue squeeze out as I can then squeeze out the glue from the straw onto the next item for gluing up as I go. Some of the other tools you were showing looked handy to have around. For the silicon spreader I bought a silicon pastry brush from the supermarket. 1,2,3 blocks are really handy if your gluing up right angles as well they are used by model builders all the time. I still have to get as set but they are soooo expensive in Australia 😿
VovaLika Family
Рет қаралды 12 МЛН
Alibaba Utilities
Рет қаралды 8 МЛН