80 Series Landcruiser | Rear Axle Seal, Wheel Bearings, & Studs **DETAILED**

80 Series Landcruiser | Rear Axle Seal, Wheel Bearings, & Studs DETAILED

Рет қаралды 17,252

Жыл бұрын

Rebuilding the rear wheel bearings, new axle seal, new studs & gaskets.
Flange stud kit
cruiserteq.com/front-axle-ais...
Axle rebuild kit rear - Bearings and all seals
cruiserteq.com/full-float-rea...
Rear axle special socket
cruiserteq.com/ff-rear-hub-so...
Parrot Nose Pliers
amzn.to/3Klawz7
Cheap Torque Wrench
amzn.to/40M54Lh
Bearing Greaser
amzn.to/3lUVV4d
Grease for hubs
amzn.to/3KmluEP
Wire wheel for drill
amzn.to/40NZojT
Brake Clean
amzn.to/3U4HdUT
Anti-Sieze Lubricant
amzn.to/42LpnKu
Rear Calipers
amzn.to/3KlfEDD
#landcruiser #80serieslandcruiser #fj80 #80series

Пікірлер: 30

@4wdingMates 4 ай бұрын

Good video overall man. But.... BEARING RACES.... if it's a emegency fix on the tracks sure reuse but when doing it as routine maintenance ALWAYS REPLACE BEARING RACE with the new ones that come with the bearing. Ps whoever has worked on those handbrake shoes has put the bottom spring in wrong location, it's supposed to be BEHIND the adjuster star wheel. Cheers

@allterraintrails 2 ай бұрын

Great video! Helped me with mine on the old 75 series. Most things are the same but no abs ring for me 😅 thank you!

@Adv4x4 2 ай бұрын

Glad it could help man!

@seansavage4766 6 ай бұрын

Awesome vid! Also, thanks for listing the parts!

@jimmymack1079 10 ай бұрын

The one part I was waiting to see was the stud removal and replacement and you sped it up! 😂

@Adv4x4 10 ай бұрын

Haha my bad! I just took 2 of the nuts thread them both in one stud then tighten them against each other! After that you should be able to remove the stud+nuts as if it were a bolt. Just be careful because they can be stuck in the hub. It’s worth heating up the stud first before you try and back it off!

@jimmymack1079 10 ай бұрын

@@Adv4x4 thanks mate

@Ghostrider-71 8 ай бұрын

Excellent video, very helpful, yes indeed, I will need to do this as well sometime soon. Thank you for posting!

@Adv4x4 7 ай бұрын

So glad it was helpful!

@paullewis252 6 ай бұрын

A very informative and helpful video. Thanks!

@Adv4x4 6 ай бұрын

Glad it was helpful! Thanks for watching!

@mikemorgan4670 Жыл бұрын

Awesome episode Buddy. While I am not very mechanically inclined I find your content very interesting and always informative. You provide very clear and concise directions which makes it understandable for the novice. Nice way to enjoy my Sunday coffee.

@Adv4x4 Жыл бұрын

Appreciate it Mike! Hopefully it’s a very informative video for people looking to do the same repairs.

@mikemorgan4670 Жыл бұрын

@@Adv4x4 It does inspire/ motivate me to take on more challenging repairs and service work on my truck.

@raullywhere3602 Жыл бұрын

Hey there! Just Finished R&R my Tacoma Driveshaft to Replace U Joints and Carrier Bearing. Your Video (A while Back) was a Big Help ! Wanted to Say Thanks

@Adv4x4 Жыл бұрын

Awesome man glad it helped!!

@guitarplayerlp7018 3 ай бұрын

just use a piece of wood from the outer hub section to knock the inner bearing & seal out in one go. In most cases the seal can be reused if in an emergency and the wood wont harm the bearing

@kankab-gd9sc 7 ай бұрын

thank you very much.

@gabemiller9873 Жыл бұрын

Next time for the bearing seal use a brass punch from the inside through. Hit the wheel bearing and the seal comes with it. Cheers!

@Adv4x4 Жыл бұрын

Great idea!

@roadstergarage9914 Жыл бұрын

Would be great to get the baselining on a couple of videos, is nice the driveway maintenance for the ones that want to tackle some of it on their own.

@Adv4x4 Жыл бұрын

Hey man! Not quite sure what you mean? I try to gear these videos towards people wanting to learn how to tackle this stuff on their own! The details can be a little much at times, but for someone wanting to learn it’s great!

@roadstergarage9914 Жыл бұрын

@@Adv4x4 Hahaha I have no idea what I wrote! First: I like that you show us how to get the maintenance done on the driveway. Second: please keep filming all the maintenance, would be great to get a series of videos of it. Third: I like the detailed videos!

@Adv4x4 Жыл бұрын

Haha copy! Do plan to show more as I keep building this thing! Next video will be on steering link replacement as well as radius arm install!

@jacksonvlogs7342 Жыл бұрын

Hey John, great video as always! I replaced the sending unit for the fuel pump, and the gauge is still reading wrong. Is it a ground issue that could be causing this still. If so, where would I look. 07 tacoma 4.0

@jibexslam 11 ай бұрын

Great video! Could you tell, what the purpose of those two juts on the axle shaft flange?

@ashtonmcmahen2137 6 ай бұрын

Hey man how did you get the new axle studs in?

@user-jh8no1zb9e 11 ай бұрын

How did the studs ''pull out'' 3.20 - i thought they'd be threaded in and you said you'd already loosened the nuts at the start of the video - You also said 2 of the studs broke - how did you get the remaining parts out ? Thanks