800HP Evo 9 on a MD, 40 psi by HDWERKS
Рет қаралды 6,517
2 жыл бұрынAfter a long road Kenny’s evo is finally on the road.
He decided to go full ham on This 40k mike evo. And here’s the rundown
Full street car spec with AC
Buschur 2.2 short block (4g64)
Stock unported head.
1/2 in head studs
AMS intake mani
ETS exhaust mani
S3 cams.
Kiggley 12t trigger kit and HLA
6266 bb
SHEP built trans and t case
Exedy tripple
82 mm Bosch DBW controlled by haltech elite.
Full titanium intercooler piping built in house
3.5 v band stainless exhaust built in house
Ecu calibration rav Motorsports.
ID 2600
Radium sending unit with dual 450 pumps
Custom PTFE fuel line system.
Etc etc etc.
Car makes great power. Put down 800 on a mustang dyno at only 40 psi. We have more in it for sure. Next round maybe a Artec v band mani and a different turbo choice.
Looking for Platinum Racing Products 🏁 Click here: bit.ly/HDWERKSXPRP
Turn that volume up!
@mohammedshane8161 3 ай бұрын
What turbo and cams are you running is it a 2.2 stroker
@hdwerks 2 ай бұрын
2.1. S3. Car just made 905 same setup
@mohammedshane8161 Ай бұрын
@@hdwerks amazing car sounds lovely mate
@christophersparkman 4 ай бұрын
2:24 What is that gauge on the steering wheel? Nice! I want for my Evo, too.
@hdwerks 2 ай бұрын
AIM dash
@silvia12319 Жыл бұрын
whats with the turbo lag, stroker wouldve been better
@hdwerks Жыл бұрын
It is a stroker. 2.2. There’s minimal lag for the power numbers
@isukarse Жыл бұрын
not even that laggy he´s just short shifting and pulling from low rpm
@Jamxknife Жыл бұрын
40 psi on a 6266 and 800whp mustang and its got more in it? Lmao what are yall saying
@effingwrecked1917 Жыл бұрын
I think he meant Engine can make more but turbo max out.
@Jamxknife Жыл бұрын
@@effingwrecked1917 Shit I hope so
@effingwrecked1917 Жыл бұрын
@@Jamxknife Well its a 4g63 40-50psi are normal. Consider I seen stock evo turbo make 30psi+ only at 350whp.
@Jamxknife Жыл бұрын
@@effingwrecked1917 I have an evo on 50 psi
@srte147 Жыл бұрын
Wayyyyy to much boost for just 800 god damn
@effingwrecked1917 Жыл бұрын
Its a 4g63. 40psi is normal. Its Not like hondas or any other 4 cylinder where 30psi max and you need a built engine. Wait until you see 80psi+.
@Jamxknife Жыл бұрын
@@effingwrecked1917 Because Hondas flow more, they’re more efficient. Boost is just the turbo shoving air into the cold side, and the engine consumes that air, the better it is at consuming that air the harder it is for the boost to build up because it’s being consumed faster than it can be supplied. So the reason it takes an evo 50 psi to make 1000whp and a Honda 35 psi on the same turbo is because the Honda is better at consuming air.
@TheAquam 3 ай бұрын
@@Jamxknife can't really argue that haha
Performance Destination
Рет қаралды 42 М.
Hagerty
Рет қаралды 477 М.