How can I get one of your carb float gauges? I have a Johnson 88spl and I've been looking for a gauge forever.

I enjoy watching you work! No BS and on to each problem with realistic and knowledgeable fixes. Keep up the great work brother!

That boat owner is lucky to have found you, expert work on the old evinrude.

My first boat had a 1985 V4 90 and it was the first time I ever looked at an outboard engine. Mine had a whole bunch of fuel hoses that were leaking and it was “fun” job figuring that out.

I love it when they bark to life. I’m putting a 4 horse Johnson (‘74) together that was submerged and full of sand, pistons were stuck, and lots of corrosion on everything. I hunted down and bought all the parts I need (took a while). Everything is cleaned up and waiting for Spring warmth to continue.

🇦🇺great video for 2024 Long time viewer I enjoy the investigation to solve the missing parts and problems

Nice gauge I will need one I'm starting to work on carb motors not too many people work on carbs ...I've been cleaning motorcycle carbs for over 30 years ... starting a change of life to outboard. I enjoy watching your videos keep them coming.

I Love your videos ! I am an automotive Mechanic in Australia and have an 1987 120hp Johnson. I have learnt so much from you videos i can't thank you enough!

I'd love to purchase one of your gauges. Your videos are awesome. All the entertainment and I don't get dirty. Be great if those float gouges were up on ebay.

Brandon, I would love to get one of those carb gauges I’ve looked everywhere scarce as hens teeth I have a1980 Evinrude 85hp I’ve rebuilt and need this bad love your videos I learned more from you than anyone and I even watched original omc videos thanks and God bless

Couldn't imagine pulling the power head off and not putting a gasket back on hahah, geez. I fix the odd boat here and there and the sticky timing tree (is that what's it's called?) happens on 90% of the engines I get. I also had to change a power head one time and I learned how to do it from one of you're videos. Thanks a ton for doing these Brandon.

Hi Brandon I love watching you videos on the Johnson out board I wish you were here in Australia mate I have a J90tlcnb Johnson could do with your mechanical skills one of your metal carb tools Love your work Cheers

Looks like an Invader Hull, which is a Flip of a Crestliner Cruisader Hull, a Jim Wynne design Improper Trailer.

I have a 1982 Johnson Evinrude. It has problems,still runs, but I've gotten advice from a good guy that fixes motors. You are one of the best mechanics I've seen. I'd like for this motor to last for my grand boys. Where are you located?

Another awesome video👌👌 I am really enjoying your content Brandon👍👍🙏🙏

Funny, I have a 1980 100 evinrude and it has the blue power packs as well. Never seen them anywhere else

Thanks!

Would love to buy one of those carb tools

I'd like one of those carburetor float tools

Thanks for the great videos. I live on the river in Mohave valley. You go by my place in some of your videos. How do I contact you for service. Thanks Tom

That motor fires better than the one with the o/s piston. I also have a fair amount of scoring on the start board bank and hit 120 psi but loss abt 3mph on the top end with inefficient combustion rough idle cuz of the excessive friction @ the damage wall oil coating.

would be intrested in purchasing a float gauge

Subscribed to your Patreon although it looks to not be used much. Great videos on here. I have a question about adding a tell-tale to a 115etl75e. Could I drill and tap into the outer cover in the location that this motor has its tell-tale? Could I possibly swap covers from a different year motor with it already installed?

Yoo where is your shop? Love your work

Watching this makes me thing my motor is really messed up !

I need one of those!

FYI, it looks like you’re using Permatex aviation sealant, denatured alcohol works really well cleaning that up. Even dried on the can. You can get rid of that aluminum foil wrap.

Enjoy your troubleshooting. I’m curious why you steer towards the power pack before checking coils. It is more likely that power packs go first? Thanks for sharing

How do we reach you to overhaul a 1976 115hp evinrude?

Why did you not remove the spark plugs and lubricant the cylinders before turning the motor over? I’m working on a 1988 Evinrude 50 hp right now and following your instructions to start a motor that has not run in years.

Hey Brandon. Good stuff! What are the 3 holes on bottom cowling for?

What is the big flat piece with the 4 bolts up the middle? Mine is leaking water out of the bottom left corner. Any idea what my problem might be? @Brandon's Garage

I got one of those in the garage, i did alot of fixing on it , one day it started running bad and someone offered me a 140 johnson , so i swapped it , it ended up i had bad fuel lines and primer bulb , the johnson wouldnt run either until i changed tge fuel lines , hell of a way to diagnose fuel lines though , kind of pricey to do it that way 😂

Can you show us how to set the timing?

How do I go about getting the float gauge? I did not see when you offered them. I do a lot of OMC outboards and have misplaced mine recently.

It was firing on top plug wasnt it looks like after you moved the ground it started sparking

I don’t know about the USA but in the uk dam straight id be in that shop claiming my lifetime warranty and they would honour it because staff can’t be bothered with an argument most the time

Nice video!! Does your gauge work on 5-15hp Johnson’s? I have 4 of those along with my 35hp Johnson. ‘83 model. Thanks Jason

I will buy 5 gauges for sure

Man everybody I know is freaking sick😢 what the hell's going on??

where you located

Brandon. Do you work on Mariners or Mercury engines

Are you self taught Marine Mechanic? Or did you go to school?

Hey man I have one just like it and I’m currently working on. Mines an 1995 88 spl johnson. Do you know what the timing at wot is supposed to be and and idle ?

Where are you located? I’d like to pick your brain for a second I’m stumped. I have a newly (November last year took it out once and then today) aquired 1986 Johnson 90hp on a VIP Fish and Ski. I changed plugs, drained old gas added new, changed lower unit gear oil. I took it out today for first run of the season and it fired up, and idled fine. We spent 4-5 hours on the lake. Then when it’s time to go dock and load onto trailer it wants to die as soon as you put in forwards or reverse gear. It will fire right up with the choke lever and will idle after you slowly lower lever. But as soon as you move throttle handle forward or reverse it dies. It did the same thing last November when we first got the boat. It’s weird it seems to not do it at the start of the day but at the end it does it every time. I know hardly anything about outboards so thanks in advance. 1986 Johnson 90hp Model # J90TLCDC

laser table guy should be able to etch the numbers no problem. i know our table could do it. just find a differnt table. maybe cause they are made from aluminum.try stainless. but i think our table has etched alum. food for thought.

Hey Brandon can i have one of those ? I will pay shipping to the UK keep me posted please bud ??

Can I buy one of those gauges?

Anywhere measurements for that float gauge to be found? I'd like to 3D print one Maybe post the measurements to the Patreon site if possible?

What is the goo that you’re using on those gaskets?

How do I get one of your carburetor float gauges?

Can I buy a float gauge from you?

I want one

I this motor for sale

🎉🎉🎉🎉🎉🎉🎉😅😅😅😅😅

I'm like close to 78.9 percent sure you sound like your under the weather.

hi.....could you share any email to contact you?.....thanks and congratulations for your excelent job

Can I buy one of those gauges?