I found white foam in the right lower cylinder, nobody seems to have an answer, but you gotta know?
@stianemanuelherdlevr987310 сағат бұрын
And i was gonna try this myself 😂
@stianemanuelherdlevr987310 сағат бұрын
I just gotta say! I could not have done this at all, i like that someone is this level of skilled, it is kinda satisfying. But i would fuck this up so badly, it couldn't even be fixed after i had touched it. And i was actually about to do this on my own. Its the same only 110 but, hell. I am just gonna slap on the gasket i tore up and screw it right back up. Hell i ain't capable of this kind ogæf delicacy. I want to, but i know my limits. And they are just about an inch over the ground. Im still in kindergarten mechanics. And i dont think i will pass from here, but hey i can almost talk to someone who knows what he is doing and he maybe just maybe he'd believe i know what im talking about, i dont even know what I'm talking about now😂
@manuelrodrigoquintanillase617311 сағат бұрын
I would like to know something about this engine. I have the same one and I tried to change the water pump. But I can’t lower the lower part where the elice is.
@manuelrodrigoquintanillase617311 сағат бұрын
Hola amigo , estoy mirando el video
@cachalotcreative38318 сағат бұрын
Years later and this video is still doing the lords work. Followed everything you did and worked perfect. Question though, how did you resolve the horn? I would like it to beep when turned on and not sure it will beep if over heated while it’s currently spliced into the harness like you have it here.
@1216gsxr1122 сағат бұрын
Tried a 3/16" rope and even put a knot in it on the handle end which the old 1958 10hp Johnson didn't call for(you run it through a channel in the handle)it pulled through the handle on the fourth pull and I had to start over. The old manual says it's 7/32 but that size rope is harder to find
@fredblankenship2319Күн бұрын
i have a 1977 85 hp johnson outboard motor. where can i get the parts i need to do all that you did in this video?
@flycatchfulКүн бұрын
The pictures on the ATM machine are for those who can't read.
@mohabirsomwaru7624Күн бұрын
I this motor for sale
@travelveteranКүн бұрын
Just bought one of these. Been sitting 30 years in someone’s garage. What do I need to fix on it before I attempt to start it?
@tomreynolds57672 күн бұрын
Hi Brandon, what’s the lowest acceptable compression on these motors for them to be expected to run decent? Thanks
@YouIskndr2 күн бұрын
Yoo where is your shop? Love your work
@to5msheppard2 күн бұрын
My buddy and I have a pontoon boat and we bought two other pontoon boats really cheap to get the metal roofs off and now we’re putting both metal roofs back to back with a solar panel on it. I don’t know why you didn’t use some metal you’ll never have to replace it, you know thin metal you can buy at Home Depot. They use it for walls galvanized sheets.
@georgehofgren61232 күн бұрын
Maybe you can comment back when you find out what Range you are getting 🤔.....
@nelllsterr2 күн бұрын
Big thanks. This helped me a lot with replacing my idle speed lever
@GoldenCroc3 күн бұрын
Cool stuff, what a find.
@NATURECOASTPDLTOURS3 күн бұрын
My issue is I have old controller and a newer outboard. I can't find the right adapter harness that works, I've ordered 3x now.
@152lb.mousehole24 күн бұрын
You obviously know what your doing...I have a '91 johnson 40hp with electric start and power T/T I'm going from a tiller to remote steer. I'm have trouble with what harness (part #) to order. Any suggestions would be much appreciated, love your channel
@knutarneaakra60134 күн бұрын
Had some of this outboards when i was young. Real crappy things, breaking rods all the times😢
@ibro47644 күн бұрын
Hello can you show me where the Johnson 50 hp 2000 2 stroke fuse is found. THANKS
@bigjay67434 күн бұрын
I have one of these engines and there's nothing you can do they are very cold-blooded.
@christoperun43804 күн бұрын
young people don't own tools or fix anything, they grew up in disposable age
@erichumphery67845 күн бұрын
Hello Mr Brandon my name is Eric and sir you are bad ass in boat motors I have a 1981 115 seahorse and I love this old motor they are beast anyway want to do my carbs but a little scared to do it myself but watching all your videos I think I can master it thanks for all your expertise your the best thank you
@rico22075 күн бұрын
Commutator
@JCFISHING21485 күн бұрын
I found this channel today and I subscribed and I actually really enjoy the videos and I have a question what do you think about ficht ram injection?
@fishydubsfishing65165 күн бұрын
The good old permatex Aviation shellac I can't believe they still make that stuff
@Minnecoldah16 күн бұрын
Thank you for sharing the idea of placing the parts on to the cardboard - excellent - I will put that knowledge to use on my current lower unit project. I have learned a tremendous amount from your content - Thank you for sharing your expertise !
@1JRrambo6 күн бұрын
" DID NOT SHOW REMOVEL OF AXELS FROM REAREND
@Brewmaster7217 күн бұрын
I have a 98 evinrude 9.9 4 stroke. It runs fine until well up to temperature. It is putting out water cooling tube when running. At wide open throttle, the engine is only at idle Any thoughts?
@stephanetalbi89158 күн бұрын
Thank you, helped me making my 140hp running awesome
@rok79808 күн бұрын
Brandon, love your videos. I would like to get your opinion on my old 1987 88hp Evinrude v4 crossflow (freshwater use). I was doing my annual maintenance and went to replace the spark plugs. I am using champion QL77JC4. My manual states the spark plug gap should be .040. I recently read on the web that Evinrude changed their gap suggestion to .030 in the early 90s to make plugs last longer. That seems like a big change to me. I am thinking I may split the difference and gap my new plugs to .035. What is your opinion? Thank You.
@kenhaworth77229 күн бұрын
I bought a competitor brand four years ago. And you are right about the value. If I sold my machine, I would have to have more than I paid for it. "Biden Omics " . But it is not for sale. Very handy machine to own. Nice video and comments.
@aztlankin19 күн бұрын
Gracias..great video sr..i need to fix the motor on my 1987 cimarron boat
@potatoesislife63659 күн бұрын
This is one of my favorite videos to come back to. It has troubleshooting, a process, and it happens to be the exact motor that I have.
@clintdunning684110 күн бұрын
If my boat is already wired with switches at the front and throttle controller will I still need a wiring harness when I swap out the tilt assist for one of these tilt/trim units? Thanks!!
@clintdunning684110 күн бұрын
I have the same motor and would like to swap out my lift assist valve for a tilt/trim setup. Do you have anything you would be willing to sell? I would appreciate it! Thanks!!
@jammiewright824910 күн бұрын
I watched a few videos, said ok, got a good one found. Pump kit came in and I couldn’t find the video I thought I saved. Found yours and it is the best one I found! Pretty much crayons and coloring book, if a guy can’t replace his outboard water pump with your video and directions, he probably should not chew gum and walk! You did an awesome job, sir!
@omarvaldez808010 күн бұрын
Brandon mi trim cuando el motor empieza a bajar hace un movimiento que hace que golpetea o cabecea,esto lo hace únicamente al bajar el motor!!,sabras a qué se debe esta falla?,gracias.
@javiermontes377710 күн бұрын
I got the same engine in the tube is leaking from the top what I need for to stop the leak
@keithconrad489210 күн бұрын
Do you tighten down that cap screw with screw driver or just tighten with hand
@BigBoldBob12310 күн бұрын
Unless I missed it, he didn't say what he did with the electrical lead he pulled off the VRO manifold. I guess he just abandoned it there.
@JuanGarcia-t1l11 күн бұрын
I have a 81 Johnson 115 seahorse and having trouble getting it running idk if my fuel lines are not right so you have a diagram to see where they run or if you could help me I can give you my contact information
@privateer056111 күн бұрын
Make your own points ignition.
@privateer056111 күн бұрын
You can get these parts used and take your chances.
@christianmello-cone983311 күн бұрын
Does any one know what he did with the wires going to the vro pump? I did this vro delete but now I am blowing the fuse when I try and start the motor.
@riverfever259511 күн бұрын
I really appreciate this video it helped me a whole lot I’m no good with electric stuff I lost spark in both plugs I run a 1985 50 hp Johnson after watching this video I’m pretty sure the “brain box “ is my problem also
@javiermontes377711 күн бұрын
One question somebody know if it's normal water coming out from the plate with for boats in the leg