No video
A Crappy Volvo 240 -76 gets a crappy turbo conversion on my driveway , and the result is ...
Рет қаралды 11,811
Күн бұрынMounting a turbo on a N/A b23e volvo engine
@danielebbeling4056 2 жыл бұрын
You live the dream that I dream of ! You have acquired the means and skills to do as you intend to. Much respect to where you are at in life!
@CalebOrvik Жыл бұрын
Wish I could bring my car to Sweden and you do the same to it
@rossconverse7038 2 жыл бұрын
Hi, years ago I added a turbo to non-turbo 2.3 Volvo 245 using all factory parts from a junk turbo 2.3 740. I ran a fmu on the fuel return line to richen the mixture during boost. It ran great immediately and pulled very strong. I wouldn't be surprised you need to do the same thing, you're probably misfiring from leaning mixture under boost. This could be verified with a wideband O2 sensor in the exhaust. Otherwise I really admire your fabrication skills. I know it's discouraging but I think there's an easy solution. Here's another quick test to prove its leaning out for very little cost. Upgrade your fuel return line with high pressure fuel injection hose then gradually pinch off the return line with a pair of pliers to raise the fuel pressure to the injectors while you're driving the car under load and if the problem goes away that proves you need an fmu. Ross, in Maine USA
@Foffe2000 2 жыл бұрын
could be a plan, and not a very expensive one either, but it still think its wierd that it breaks up at the same rpm on load and off load and that it even did it before the turbo installation, so i am going to take a look inside the distributor and see if the springs are okey that pulls back the weights for advancing the timing.
@rossconverse7038 2 жыл бұрын
@@Foffe2000 Sorry, I missed your comment on the video that it was doing it before the turbo installation. If it's misfiring with no load but just at a certain RPM each time, it might be interesting hook up your timing light and then watch to see if the timing on the front pulley changes at that rpm when it cuts out. If it advances normally as you bring the revs up from idle and stays at that point as the engine is cutting out I think you'd know the distributor is doing its thing properly.
@JstGdNews 2 жыл бұрын
Fabulous flat hood!!
@Foffe2000 2 жыл бұрын
not all flat anymore, but these "bricks" got a styling like no other car out there
@BeardedWrencher 2 жыл бұрын
I love it! First off, wonderful video editing! Secondly, I love the old brick and the engine, trans and turbo swap is amazing. I am hoping to turbo swap my 1985 sedan I rescued last year someday. I have only ever briefly owned a turbo Volvo but I hope to eventually change that!
@Foffe2000 2 жыл бұрын
Around here old volvos are understandebly pretty easy to come by. And tuning and trashing on them are also common. Good luck with your own volvo project
@racingonempty43 2 жыл бұрын
Sweet! I have a 240 with b23 that I've been thinking about adding a turbo to. Wonder it the kjet fuel system is up to the task. Would love to see some more videos to see if you can get it to run right!
@Foffe2000 2 жыл бұрын
well, this one didnt run properly at all.. but k-jetronic SHOULD be good for turbo application. The injectors puls in fuel continously on numbers of squirts per second and doesent care about where the piston is in the cylinder, it only acts on the engine rpm and the mechanical air-flow-meter witch is basicly just a flap on hinges. At the same time i havent gotten this one working properly (yet) so dont take my word for it.
@racingonempty43 2 жыл бұрын
@@Foffe2000 yes, that was my thoughts also. Really seems simple enough. As long as the boost level isn't too hight the fuel flap should be able to adjust fuel accordingly.
@MickeyMishra 2 жыл бұрын
well that one guy from boost SE or whatever his shop is did a diesel conversion or you converted his block to Diesel and that seemed to work pretty well for him. he installed the diesel injectors where the spark plugs were and to use something like healicoil or I forgot what type of Steel inserts but it worked pretty well for him. he installed the diesel pump on the front of it and of course it was turboed and he also used a fuel preheater to get the fuel up to a very hot temperature from an oem volvo fuel heater. You could do the same thing with one of those GM Hot water sprayers so the fuel would be hot the second it came out of the pump. I believe his fuel pump was off of a Volkswagen and it was driven by a cam belt. Do not give up. but I completely understand your frustration with K Jet.
@frankk.5548 2 жыл бұрын
lol - the empty shells on the panel - are they for mad-max ignition modus ^^
@Foffe2000 2 жыл бұрын
haha its a good start and the car itself is a good canvas for a mad-max car. The real reason is that ive used this car for elk-hunting in the past =)
@Kall33 2 жыл бұрын
Awesome video! Can you film more like that "timelapse" type content
@Foffe2000 2 жыл бұрын
theres more coming, but got a winter break soon
@doktorjonsson3860 2 жыл бұрын
Pros and cons of a turbo B23: Pro: Turbo Cons: B23 😁
@Foffe2000 2 жыл бұрын
i saw yesterday that the world record (according to them self) are 1000hp out of a 8V b23 , so its up to the fabricator (me) to prove myself now 😂 just another 950hp to go!
@doktorjonsson3860 2 жыл бұрын
@@Foffe2000 If you mean Rickard Thomsson's drag racing car it makes even more, probably 1600 crank HP 😁 Insane engine, almost 20mm lift on the cams, billet head, 98mm turbo and injectors that could work as a fire hydrant 🙈
@Brad-lt6mr 2 жыл бұрын
Over 20 years ago I fitted a B21ET to a RHD 244DL. Volvo never made a RHD turbo 240 because the turbo would be very close to the steering column. The existing loom plugged straight into the donor engine loom. I just had to fit a fuel pump relay and wiring to the in tank pump. I had four 200s at one point.
@Foffe2000 2 жыл бұрын
at least around here volvo got the reputation being a little bit like IKEA when it comes to parts and how they intercept between different years and chassies of volvos.
@Brad-lt6mr 2 жыл бұрын
@@Foffe2000 I love Volvos of this age. So reliable and easy to repair.
@pierrejonsson9224 2 жыл бұрын
Great Work! Keep it up!!📽👍👏Foffe! Du fick precis en ny prenumerant! Du e duktig och roligt att kolla på dina filmer , egna ideer o lösningar. Jag har egen bilverkstad så jag vet hur mycket arbete det ligger bakom dina klipp.
@Foffe2000 2 жыл бұрын
Hej Pierre , tackar. Nu håller vi tummarna att ja räknar ut som vad som saknas gamm-volvon då den inte varvar som den skall. Bränsletrycket säger dom flesta men jag sneglar fortfarande på tändningen då fenomenet var densamma både före och efter turbo-installationen. Men nu är det vinteruppehåll å nya tag till våren
@skateerjesus3991 2 жыл бұрын
Amazing video
@Foffe2000 2 жыл бұрын
Thanks!
@rbscreations71 4 ай бұрын
Foffe it could be your fuel pressure regulator is bad or pump cant supply enough fuel , check filter also, also check spark plug leads foffe, The engine sound to me like your not getting enough fuel for higher rpm
@Foffe2000 4 ай бұрын
I did check the fuelpressure .. that fuel-line over the roof was the return line .. if it would starve for fuel i should have had less/no fuel trough the returnline .. I didnt count on that this K-jetronic dont calculate the air-pressure .. as it was i only measured the air-flow
@cullenmiller8170 2 жыл бұрын
Looks like you need to convert one of your buildings to a shop so you can work on cars in the winter too. I guess the forks are coming off soon and will be replaced with a bucket to move snow. Are you sure you getting enough fuel at the higher rpms?
@Foffe2000 2 жыл бұрын
Hey Cullen, yeah some garage would be nice. But i do not deserve one since i dont keep things organised. And further more there are some threats with getting a forced break from fixing the mechanical things, i got other hobbies to and i get more time for them during the winter months. Regarding the volvo engine i am not sure on anything, but i do think the span of the ignition feels to be way off. so i am going to take the distributor apart and look if both the springs that hold back the weights inside are there and not broken.
@Appelsap1337 2 жыл бұрын
Nice 242. I think the fuel system is the problem, the mechanical injection never works good anyway
@Foffe2000 2 жыл бұрын
yeah it might be a reason why they did didnt make that system for that long. The work done so far doesent have to be remodeled for me adding a haltech system later on tought. It makes for funnier videos if i use trial and error and fix stuff as i go
@saltypea7834 2 жыл бұрын
whats that blue tubing that you use for mock ups? its wonderful!!
@Foffe2000 2 жыл бұрын
its a mockup tool for piping, the manufacturer is "ice engine works". They are quite expensive i think i paid about 1200 dollars for the big kit. If you are about to buy a 3d printer or know someone with one i would recomend trying to make a few yourself first and see what you think about the system.
@garagefix3003 Жыл бұрын
I love the idea but im thinking of doing the same so i am wondering where you got all the parts from?
@Foffe2000 Жыл бұрын
Det tyck ja absolut ni ska göra grabbar, eran 240 verkar ju redan gå bättre än denna men mycket vill ju ha mer! Det är en saab 9000 turbo och faktiskt original K-jetronic insprutning som kom på volvo 240 GLT modeller (bland annat) kring 1980 och fram till 87-88? typ. Inför nästa säsong blir det nog svenskt Maxxecu insprutning om jag får allt att fungera.
@garagefix3003 Жыл бұрын
@@Foffe2000 Ok tack men tror du att jag kommer behöva byta insprut på den det är en 1988?
@Foffe2000 Жыл бұрын
@@garagefix3003 från och med 88 har du lamda-styrning på avgassidan och troligen modernare luftmassemätare av samma stuk som bilar har än idag 2022. Alltsammans är bättre grejjor än det jag håller på med i videon ovan, dock troligen svårare å manipulera. Men du bör inte ta råd av mig på ämnet då jag som du ser i videon inte fick motorn att fungera ordentligt på högre varv, det blir som sagt var troligen eftermarknads insprutning nästa säsong för min del.
@garagefix3003 Жыл бұрын
@@Foffe2000 Ok Tack Så Mycket För Tipsen! Och Lycka Till På Dit Projekt.
@soulis1000 2 жыл бұрын
Some 6,5x55 casings och the dash?
@Foffe2000 2 жыл бұрын
good eye! yepp thats 6,5 alright
@RedneckTipsByScott 2 жыл бұрын
Try closing your plug gap
@Foffe2000 2 жыл бұрын
free and good tip, but i had the same problem before the turbo installation
@eliasisraelsson2510 8 ай бұрын
Behöver du inte använda en wategate
@Foffe2000 8 ай бұрын
Den har en wastegate, det är originalmonterade för turbon, sitter i bakkant. Tror jag nånstans i videon visar när jag ställer ner den för att få ca 0,5bars laddtryck.
@cheif3870 Жыл бұрын
No way you put a turbo on a k jet system!!!
@alexanderlindh3557 2 жыл бұрын
Vågat turbo på en b230e!
@alexanderlindh3557 2 жыл бұрын
Ps du behlver större spridare kan va anledningen för att den inte orkar köra på högre varv, kör saabs gröna spridare
@Foffe2000 2 жыл бұрын
@@alexanderlindh3557 detta är B23E med k-jetronic, den har visserligen spridare men det är "mekaniska" spridare som gör insprutning kontinuerligt oavsett vart i tändningscykeln motorn är, den ändrar bara mängden bränslepulser beroende på hur mycket man gasar.
@Foffe2000 2 жыл бұрын
B23e
driving 4 answers
Рет қаралды 1,2 МЛН
Garena Free Fire Global
Рет қаралды 9 МЛН
Baked Beans Garage
Рет қаралды 3,6 М.