A First Day Scrape with Benjamin Kamins

Рет қаралды 15,566

Күн бұрын

Benjamin Kamins, Professor of Bassoon at Rice University's Shepherd School of Music, demonstrates clipping and adjusting a new bassoon reed in the Herzberg/Kamins Reed Making Method.

Пікірлер: 20

@bsnguy12k 6 жыл бұрын

Wow - I was still studying with you in May '81!

@celticbassoon 3 жыл бұрын

Thank you for this video as I continue to adjust my reeds and look for guidance from others!

@mattlengas2394 6 жыл бұрын

Looking good Mr. Kamins!! Very interesting stuff

@dorelteican4419 6 жыл бұрын

BENJAMIN KAMINS ! ! !

@jhodgebassoon 4 ай бұрын

Does anyone have info on where one might find the Japanese woodworking tool (or something similar) he uses to cut in the tip?

@scotking3436 4 жыл бұрын

Not me. I bought cane from Bob Gilbert! I actually attended a masterclass with Herzberg back in the day.(1980) I was there with David Sogg, Seth Krimsky, and some others. I should have stuck with the bassoon. I was working with Michael O'Donovan. Prior to USC I worked with Kay Brightman. I never got a close up reed making class like this though. Thank you for sharing.Scot King.

@juancarlosmoracordova1135 2 жыл бұрын

EXCELENTE MSTRO.‼️👍🎶🇪🇨

@homerhomer1776 3 жыл бұрын

Hello Kristin, i'm an hold bassoonist, i never eard such a beautiful musical introduction, can you help me finding the name of this music? Very thank you from Italy

@kristinje1 3 жыл бұрын

Hello Homer! The introduction music is Vivaldi's Bassoon Concerto in C major, RV 479, arranged for 5 bassoons and contrabassoon by Nathan Koch, available at Trevco-Varner: www.trevcomusic.com/products/tco-3129-vivaldi-concerto-c-sc-pts-bsn-4bsn?_pos=24&_sid=b998aa4c1&_ss=r

@jmhohlfeld 2 жыл бұрын

I realize it's been over 3 yrs since anyone commented, but I hope someone will see this question and answer it to the best of his/her ability. About about 9'30" to 10" into the video Kamins is discussing the thickness at this reference point (8mm or 5/16") and says it should be 0.60mm or 24/1000" but only on a reed made with a profiler that makes no spine to edge taper. He goes on to say that with a profiler like a Rieger, that reference point should be thicker to compensate for the spine to side taper, BUT he does not say how thick. Can anyone give a reliable thickness for the 8 mm point on a Rieger-profiled reed?

@nathanielechols4220 5 жыл бұрын

I understand the pedagogical value of learning how to do this by hand (I started the same way, like everyone), but do all of Kamins's former students still make every reed this way, or do they just use a tip profiler?

@riancraypo6472 Жыл бұрын

It's a balance. Those who are lucky to own Herzberg profilers don't use tip profilers, others have Greg James profilers/reed copiers, others use tip machines with custom Herzberg pattern blocks (#11 if you're ordering from Rieger), others have Maxwells or MG's or other single barrel profilers and finish by hand.

@hansfronberg4369 6 жыл бұрын

What would be the advantage to doing the filing on the reed against the grain as compared to with the grain? Assuming that the file is still kept parallel to the work table.

@kristinje1 6 жыл бұрын

If the file is a conventional file, it will not cut going with the grain. It has to go across the grain in order to be effective. Otherwise, all it will do is make grooves along the cane without removing any wood. If it is a diamond file, ostensibly you can have it go straight up and down, however, I have found it is difficult to keep a good taper to the reed as it will tend to gouge out places instead of drawing all of the tapers together as a whole on the reed. People tend to be very positional when it comes to the work they do on reeds and don’t see the totality of the work as it affects the whole blade. (From Mr. Kamins).

@hansfronberg4369 6 жыл бұрын

Thanks for the reply and input! I greatly appreciate it!

@dylantharp87 6 жыл бұрын

My teacher Karen Pierson who was Mr. Kamins' colleague in the Houston symphony files with the grain when she uses a diamond file. Having only diamond files myself, I find that it takes cane off really slowly and tends to skate a lot more on the fibers that are being removed, so I prefer to go diagonal to the grian. KP uses her files pretty much like a stick of sandpaper --which I guess they are in a sense-- with one finger above where the cane is being removed on the file, so I guess it depends a lot on who teaches you and your own personal findings as you are making reeds.