A quicker easier Stealth Shelf.

Рет қаралды 40,856

Күн бұрын

I showed you how to make a stealth shelf before but that one was kind of a pain in the a$$. Here is a quicker simpler way to make one. I used a different lock on this one too.
Slow open air spring : amzn.to/3E43j0q
Motion Sensing Light : amzn.to/3m1rGG5
Hinges : amzn.to/3FnwFrE
RFID Lock : amzn.to/3JwhwHQ
Magnetic Locks: amzn.to/3b37AVm
Foam : amzn.to/32Ua1cJ
I found the foam on Ebay under the description
Customizable Polyethylene Foam Pads for packing and crafts, 1.5 in

Пікірлер: 45

@toyT100 9 ай бұрын

Mans said fuck it, I'ma put a shoe box on my wall and hope no one assumes a firearm is in it 😂😂😭

@LastLeafStudioVideo 9 ай бұрын

🤫🤫🤫🤫😂

@OBSLyfe 7 ай бұрын

That's some funny shit 😂😂😂

@tooshieg2059 9 ай бұрын

Luv it! Thanks for sharing. Although, I hate locks that click and beep when opening

@LastLeafStudioVideo 9 ай бұрын

Hmm I wonder if there are silent ones? I know there are magnetic ones.

@race091 Жыл бұрын

That's kick ass I like it

@LastLeafStudioVideo Жыл бұрын

Thank you

@rogerthatusa 11 ай бұрын

Right to the point. Good stuff

@LastLeafStudioVideo 11 ай бұрын

Thank you

@jack_knife_customz2966 2 ай бұрын

This is so nice. The only part messing me up is how’d you know the spacing for the reader.

@LastLeafStudioVideo 2 ай бұрын

There's a template that came with it and then a bunch of trial and error.

@agustin1736 9 күн бұрын

Buen trabajo, como se llama ese tipo de cerradura?

@gruss5157 9 ай бұрын

Saw this video 🎉 subscribe🎉 great job two thumbs up

@LastLeafStudioVideo 9 ай бұрын

Thank you, thank you

@smgibv4393 11 ай бұрын

Quicker amd easier than what/which one?

@LastLeafStudioVideo 11 ай бұрын

This one kzfaq.info/get/bejne/r7ifhM59v8WuoWQ.html

@wickedone7548 Ай бұрын

How much for one of these

@LastLeafStudioVideo Ай бұрын

I'm not really selling them anymore.

@MLopez-lw2ct 8 ай бұрын

I like the build. Did you show how to hang it or did I miss it?

@LastLeafStudioVideo 8 ай бұрын

I guess I didn't. If you watch the end you can see two screws on either side of the light that go through the back piece.

@vuztamante Жыл бұрын

❤

@LastLeafStudioVideo Жыл бұрын

😎

@oincer3943 Жыл бұрын

What type of wood did you start off with and measurements ?🤔

@LastLeafStudioVideo Жыл бұрын

It's pine with a dark Walnut stain. I'm pretty sue the top measured 18" long x 10" wide plus the pieces around the edge. Sides of the bottom are 1x4 measured to fit inside the top with an 1/8" gap all around except the back.

@joestatella1049 Жыл бұрын

Where did you get the lock from? Do you have a link?

@LastLeafStudioVideo Жыл бұрын

Just added one to the description. amzn.to/3JwhwHQ

@johnrenas5754 7 ай бұрын

where can i get the open and close mechanism?

@LastLeafStudioVideo 7 ай бұрын

Link in description I think

@keithmotley2268 5 ай бұрын

what hinges did you use ?

@LastLeafStudioVideo 5 ай бұрын

@@keithmotley2268 110 degree full overlay hinge

@SLickev92 Жыл бұрын

What’s the point of the groove made at 2:20?

@LastLeafStudioVideo Жыл бұрын

You have to knock that corner off so it will close properly. Yeah I didn't do a good job showing that.

@SLickev92 Жыл бұрын

@@LastLeafStudioVideo oh okay got it. That top piece is 18x12 right? Nice build.

@LastLeafStudioVideo Жыл бұрын

@@SLickev92 I believe it's only 9 1/4 x 18 but I can't remember. I'm sure 12x18 would be just as good if not better

@SLickev92 Жыл бұрын

@@LastLeafStudioVideo ok cool . 9 and a quarter sounds better cause I’m trying to keep it more compact .

@1991DesertVet 8 ай бұрын

Are you using the Ryobi brad nailer or pin nailer? Which one do you recommend?

@LastLeafStudioVideo 8 ай бұрын

This is the Brad nailer. I would actually recommend no nails for this project, but I am very impatient so I used them instead of clamping.

@1991DesertVet 8 ай бұрын

Thanks for the info. I would rather build them faster too. Plus it would give more peace of mind that they won't come apart.

@LastLeafStudioVideo 8 ай бұрын

@@1991DesertVet yeah it's always nice to have that little bit of backup

@1991DesertVet 8 ай бұрын

Yep. I'm planning on going to Home Depot to buy one today. Gotta try out my new table saw now too.

@LastLeafStudioVideo 8 ай бұрын

@@1991DesertVet nice. Good luck

@user-kn8lr3zm8u 6 ай бұрын

7:37

@LastLeafStudioVideo 6 ай бұрын

What is it?

@bigmacboney 2 ай бұрын

Quicker!? Easier!? Yea when you fast forward the video,it's quicker! Click bait like a mofo

@LastLeafStudioVideo 2 ай бұрын

I think it's a lot quicker and easier than the one with crown molding and magnetic lock.