ABS, ASA, PC, Nylon and POM on my newly enclosed Flashforge A5M.

Рет қаралды 443

21 күн бұрын

Adventurer 5M - amzn.to/3VSG6dk
Adventurer 5M .06 hardened nozzle - amzn.to/4c7sctE
DIY enclosure kit with panels - amzn.to/3xwFfFX
DIY enclosure 3D prints - wiki.flashforge.com/en/knowle...
Tools and equipment I've reviewed, use and recommend.
Use VVS10 for $10 or VVPROMO for 5% off Vevor products!
Welders, plasma cutters and welding equipment
Vevor MIG 270 $289 - s.vevor.com/bfQTds
Vevor MIG 145 $132 - s.vevor.com/bfQSka
Bestarac BTC500DP Plasma cutter - amzn.to/3XiSyEr
Yeswelder welding hood - amzn.to/3VedwA5
Leather welding apron - amzn.to/3tK3lrd
Vevor Cut 50 Plasma cutter s.vevor.com/bfP8hO
Vevor welding table - s.vevor.com/bfQnKp
Automotive tools and equipment
Launch X431 FGC OBD2 Scanner - amzn.to/3QwR6dg
R500 auto paint spray gun - amzn.to/3VHVCJA
Adapter for disposable cup system - amzn.to/3PRvnwA
Disposable cup system 10 pack - amzn.to/43QBBm6
AEM 30-0300 X-Series Wideband kit - amzn.to/3Tbpw7s
Godiag GT101 power probe - amzn.to/3QxhZyM
Mrcartool T100 smoke leak detector amzn.to/3LUlgoG
Ancel AD410 Pro OBD2 scanner - amzn.to/4cgdJvj
Ancel BM300 bluetooth battery monitor - amzn.to/3ViCAaU
3D Printing
Creality Ender 3 3D Printer - amzn.to/3UmN46B
Chitu Systems PLA+ - amzn.to/3Uzh1T4
Smart Watches
Lige T30 at Aliexpress - s.zbanx.com/r/jpOX1Rb5B4Fp
Colmi V69 at Aliexpress - s.zbanx.com/r/RFgRUTpArDjO
Shop equipment
10x10 canopy at Harbor Freight - sovrn.co/8np189e
JCD-8898 Soldering/Reflow station - amzn.to/3IvNbJw
Vevor Ultrasonic Cleaner - s.vevor.com/bfQQdS
Vevor 13b drill sharpener - s.vevor.com/bfQGW2
Vevor diesel heater - s.vevor.com/bfP446
Evap cooler at Amazon - amzn.to/3x6grEw

Пікірлер: 13

@grasstreefarmer 18 күн бұрын

The internal chamber temp is the single most important factor for avoiding warping. Enclosing is good, but a good complete seal of the chamber is better, and either letting the chamber pre heat using the bed or using an active heater is best. A chamber temp of over 50C is what you want for relieable ABS / ASA and 60C+ for polycarbonate. With good chamber temp you don't need glues or anything special, just a PEI surface that is cleaned with alcohol between each print.

@AndrewAHayes 20 күн бұрын

For printing POM, you will need a heated chamber of between 70°C and 80° and pre heated for 10 mins or so and a bed temp of at least 120°C and print it extremely slow, around 20mm/s

@oneanother1 19 күн бұрын

Check out getting a carbon fiber sheet for printing nylon, scuff it up, use some aleene fabric glue and some vinegar on the carbon fiber sheet. Best surface I ever found for printing nylon.

@NoMercyFtw 20 күн бұрын

With PC you should heat the chamber, put the thermometer in there and try and get get to at least 60, 55 will work most of the time

@42earthling 3 күн бұрын

Hey Chuck, your videos are a really good display of how this 3d printer performs. For me as a beginner this is so enormously helpful. :) Thank you and greets from the Netherlands. Ohh and i subscribed.

@3rdpig 3 күн бұрын

Thanks! And it's always nice to hear from like minded people from around the world!

@winandd8649 19 күн бұрын

ASA should not warp any more than ABS does. I guess it might be the specific brand you use. I've been printing for 10 years now and only in ABS, and the last years ASA is slowly replacing ABS as my go to filament. It has all the good stuff of ABS as well as UV resistance, so good for outdoor stuff.

@3rdpig 19 күн бұрын

I've printed with a bunch of different brands of ABS and never really noticed any difference in warpage between brands. I've only printed with one brand of ASA and I guess I just assumed that like ABS it would all be about the same. But based on this one roll, it seems to warp quite a bit more than ABS. But I'll get a different brand and give it another try. Thanks for the comment!

@chriskreutzer1300 20 күн бұрын

Have you added any filters for printing these types of filaments?

@3rdpig 19 күн бұрын

What kind of filters are you talking about?

@chriskreutzer1300 19 күн бұрын

@@3rdpig There are hepa filters that flashforge sells that go behind the grates in the back of the main print chamber. They come standard in the 5m pro. Not sure if they help with anything without adding fans behind them too. But just wondering how the fumes from ABS and ASA were without filtration or ventilation.