2024 New invention for cars never made before 👇👇 kzfaq.info/get/bejne/beCCmbClutnDdGg.htmlsi=VkNr9-a4qE7uYoXH

Nice welding, but maybe there's a reason why these are not commonly sold . Huge risk involved .

Nice first attempt. But it would be more useful for cars that can't move under own power if the 4 rods were wider, and are inserted into receivers. This way you position it under the car, insert the 4 rods front and aft of tires, and lift. Lower the car elsewhere or when done, pull out 4 rods, remove the assembly and jack.

Nice, but where was the clip of the car driving up onto the round stock? While it was balanced on the jack, the round bars weren't on the ground.

thats a good idea and well built. i would change piece in middle and make it go in the hole on the jack after removing the lift disc. but over all this is awesome

Absolutely brilliant well done mate cheers

Those welds at the end rods are impressive!

That's very good for vehicle's without a central jacking point, and yes you have to use jack stands.

Really impressive tool, I will build one similar myself, but have ideas for modifications to where one could use it for cars as well concerning ground clearances to bottom of vehicle

I need to build one of those for a 3-point hitch to move my project cars around. Great idea! Just add a ratchet strap over each tire.

Great idea. Thanks for sharing that

I would definitely say test it on different weight cars so you know it’s tension strength. This is a great build but I’d like to know it’s weight capacity.

Great idea, will be making my own. Will add a couple of threaded stantions like harbour freight to lift rear axle. Maybe insert heavy wall square tubing or solid square bar inside lifting beam for more center strength, weld in with rosette welds. Thanks again!

Great idea for uniformity of lift. I also enjoy repairing my own vehicle. Vetri South Africa 🙏🇿🇦🙏

Sure is robust....and an awesome tool.... Thanks

One improvement I would do is add some gussets from back of wheel to about 3/4 of the way to the lift point. That would help on the deflection as you lift.

This would make it easier to place jack-stands. Keep innovating! Nice

This is a killer tool for sure. Could I make one from aluminum to save weight and have some sort of contraction for easy garage storage ???? Thanks

I wouldn’t trust it with out blocks under the wheels, so if you have to use blocks why not just use ramps. It’ll be easy to weld some drop down stabilizing legs on it though , maybe some straps over the tires to fasten it down .. Pretty good idea 🤙

I’m retired welder. Love mug welding! Squirty Squirty! Sweet idea!

Awesome idea. My truck is lifted and it’s a pain in the ass to Jack it up. This is perfect. 👍👍👍👍👍👍👍👍

Excellent time saver. Great video. Thank you!

I see a business opportunity here. Do the necessaries and see what happens. Brilliant idea!

Really good idea and awesome creating! Nice job! :)

thatsa great tool and could be modified for use on light duty trucks.

Bro amazing 👏

I love it! I want one! The sad part is I wouldn't be able to pick it up to get it on the jack. Bad back. 😢

This is a simple and interesting device, but it is only suitable for cars with a huge ground clearance. Most modern cars are not compatible with it. The device will only work with the back where there is a void. In front, there is the suspension, the engine crankcase, and its protection, there is barely 130 mm clear. In addition, a square pipe for heavy cars needs to be reinforced with scarves from the bottom to ensure sufficient rigidity. Because even in the video you can see how the pipe bends. After 10 lifts, it will take the shape of a hemisphere.

Very nice Welds!

Espectacular genio muy bueno me voy hacer 👍

Definitely would have to get jackstands under it for support in case the hydraulic jack failed.

Could use a little more distance between the tire bars.

awesome idea !

Definitely need to get a lower profile and a better jack with a lower profile jack the round bars will all sit on the ground and I would put a bigger round pipe in the center for the jack. Yes I would Definitely use hevy duty jack stands

great work

This is a awesome job you have done here. Just a little suggestion,maybe add a couple tabs on the round bars to front and back to put a ratchet strap on. Maybe on a slight up angle, just a thought.

Великолепная идея и отличное исполнение! Меня оно навело на мысль для универсализации под разные базы и не только под колеса.. Огромная благодарность и удачных идей в будущем!🤝 Теперь я знаю, что и как сделать в гараж под джип и легковушку!🤝

Great. Job. Thanks for Tip I am. Going Make one at My. Welding Shop 🙏🇨🇦

Great job , s that wheel under pressure?

Love the idea, so why no just make it jack up both side but make it catch the shock or the axel or some other point that succure enough to lift both side. Your fab work was very impressive. Maybe just change your point of contact. Then you won't have to brive the vehicle over it and you could service everything under the vehicle without to hack up one side at a time!! Just my opinion brother!! Over all tho, great fab work!!

I can't figure out when you would use this when 2 jackstands would suffice. Of course it is cool to make things I do it all of the time.

Very cool idea! I believe I’ll make one

Not having the tools to build it i would BUY one of those jack systems….brilliant when you need to get under your whole car, just add a couple of jack stands and work in total secure comfort1👍👍👍👍

The steel car lifting bar looks great. But your Center is not strong Enough! You will lift a couple of times then it will collapse in the center. Please do not risk your own life.

Se o carro mexer pra frente um pouco ele cai, ficou perigoso, se fizer as barras um pouco mais distantes para abracar melhor o pneu e deixar o centro de gravidade um pouco mais baixo vai ficar perfeito! Parabens pela idéia criativa!!!!

Nice build. Thank you for sharing your video.

Love it where can I buy it

I wouldn’t trust my life with that contraption! A couple of decent ramps, and couple of jack stands for redundancy are more than sufficient and you’ll get more space under the car.

A fun project and useful for certain applications. I always wondered if someone makes air-rams to mount permanently under a vehicle to lift either of the four wheels for a quick tire change like in the Indy 500 pits? Be nice if you could just hook up to a small compressor, lift either of the 4 off the ground, and it would always be there underneath for when & if you get a flat tire in the dark and/or during shitty weather.

Excellent job

Excellent idea for lifting a car evenly to fit the axle stands. Very nice welding.

This might be good for pick up trucks if you don't have long reach floor jack. Once up, drop on jack stand...

Wouldn't need that often, could just use the jack by itself. That would come in handy for vans with the twin I- Beams though. You can't lift them up dead center in the front.

I love it! This is brilliant. Ignore the negative comments.

Definately a nice idea

Ух ты! Классная идея!

Great job on it like it

I was going to buy air powered since they use this idea to lift buses. This is s good idea of jacking it up to wood cribbing stands

Nice job 😊

Looks dangerous. The car could roll right off😳

something to be built for the jack part itself, so it doesn't slip. can you raise it higher or was that the maximum height ? also, make connections for the jack stands to hold it, so you can make front and back ones. raise the whole car

Useful build to get one end of vehicle up on jack stands.

Well done!

Nice I'll have to make one But lower profile

It's nice, but can you just jack on the center of the subframe to lift the front up?

would be a lot better used with a low clearance jack to bring down the height of it, great for transverse engines where they either have no jack point at the front or its off set due to the engine, g'box layout

Clever design. Has a few practical and safety draw backs. Keep at it. Work safely. Not exactly sure what work you would use it for. Side access wheel dolleys would be more practical.

Genius!

This thing gives me anxiety but safety stands can help, also this contraption is for tall vehicles not low clearance ground cars, overall nice time saver!

Good job mate 👍👍👍

Me gusta la idea👍👍👍

One question!! What good does this do. You can't change the tire. You can't service the wheels or breakers !! Very nice fab work for sure , just don't get the point!! Other than that, great job!!!

Other than an oil change, what can you do with this contraption?

I’d like to see something similar for raising large tires to install on lugs..I have a truck with 20 in wheels and 35 tires and I’m older now those things are heavy…maybe something exist for that?

That's great! But how will that help rotate the tires? Or do a brake job? 😳

très pratique lorsque tu veux retirer les roues arrières 😄😄😄

The reason I Jack the car up and put Jack stands is so I can roll around under the car without having a big long piece of tubing stopping me in my tracks. I honestly can’t think of a reason why this would make anything easier for me. Maybe I’m just slow and haven’t thought deep enough. Nice job making it,and if it works for you that’s all that matters.

looks impressive but if you can i would use good quality ramps, i found they work better and safer than anything else i have use except for 12 in blocks with 4x4 on top of them so the blocks dont split,

What is the brand of that blade, and can it be used on a regular chop saw such as a Rigid 14" chop saw? I like how it doesn't put off a ton of sparks and all the dust that comes from typical chop saw blades.

Just use subframe mounts as jack points instead? What do you do when it's up in the air? You'd still want something other than a jack to hold it up while you get under the car. A pair of ramps would be even faster to use and easier to store. Nice metal work but not sure what problem it's solving!

Ok good .now I want to see it how you going to take the tires using that?

Or you could just jack it up with just the jack and accomplish the same exact thing without having a giant heavy metal bar taking up all kinds of room in the shop

I hope my mechanic has one of these.

Good idea but I think the metal needs to be reinforced somehow more metal

I think it would be stronger of you put the round bar in a wider I-Beam, instead of next to it.

Good idea ... just reinforce the center part it's bending alot..

OK, it looks like it's working! However, anybody building something like that does not need to watch every single weld from A to Z and, in my opinion, there seems to be quite a bit of overkill

Das ist ja mal richtig geil. 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

Interesting, I own jack stands and only use a floor jack for emergencies, & would lift one side at a time if I needed both rear wheels off the ground. Otherwise vehicles go up on my Rotary lift.

brilliant video 😎 need more than 2 ton jack 🤔 I only jack up my car when I'm fixing something,so usually have to remove wheel

This is nothing new you can actually buy them.. But to see an independent man make one brilliant. Make sure you use support (jack stands)👍🏿

A little sketch, how did it get around the tire? Doesn't pivot like a tow truck stinger. Also needs to be taller so jack would clear without lifting on the jack pad. Still needs Jackstands for safety.

What if you have to take the tires off?

If you have a live axle rear end, just put the jack under the diff housing.

How do you change the tire+wheel with that?

No metal prep prior to welding; just saying Nice idea, especially for pre-jacking vehicle prior to installing jack stands on frame so as to work on brakes etc

I don't know, It looks great but I would rather use the materials to make some car ramps at home...

Good idea, there isn't much on the rear suspension of a FWD car to support lifting.

Great idea no doubt.. Have a few ideas to possibly improve upon the original design: 1. Make a sort of stay (or a small cutout) for the under side of the tool to ensure its exactly centered on the jack 2. Make the rods under the wheels roll. Meaning the Thinner pieces under the tires actually spin with the speed of the tire. Sort of like a dyna setup 3. Possibly make the lifting mechanism lift from the rear-end vs. Lifting from wheels Therfore freeing up the wheels for tire work/, doing brakes, etc

Cool idea. I like it. He made it because he could. Not everyone has killer welding skills. About the only thing I would have done differently is make it adjustable to work on multiple vehicles. Regardless, it's bitchen!