Garage Door Opener Troubleshooting and Repair

Garage Door Opener Troubleshooting and Repair - How to fix common problems

Рет қаралды 3,838,194

Күн бұрын

Replacement parts for your opener → goo.gl/EUHkMp
Be sure to click "show more" read the full description below for more help and more detailed repair videos.
For those who offer to buy me a drink, thank you! I have Venmo and CashApp.
CashApp: $AdamDIY
Venmo: AdamCash
0:40 NO POWER
-First check the breaker switch
-If that is good you may have a burned-out power circuit board
1:20 REMOTE WORKS BUT WON'T OPEN DOOR
-Check to see if the 'Lock' mode is engaged
2:19 LIGHTBULB FLASHES WHEN BUTTON IS PUSHED - CHECK THE SENSORS [most common failure]
-Verify that nothing is in between the two sensors
-Make sure the sensors are aligned
-Verify that both sensors have lit LEDs
-Verify no dirt or spiderwebs are blocking the sensors
-Check the wires for breaks and follow them back to the opener unit. Make sure they are completely inserted.
-Sometimes snow can cause the sensor to trip. Even morning/afternoon sunlight shining into the sensor lens can cause it to trip.
-Override the sensor by holding down the button. If the door closes properly, you know you have a sensor issue. Sensors can fail but it is not common.
Watch this video for more info: • Garage Door Repair - w...
5:18 REMOTE NOT WORKING
-If you need to push the remote several times to get it to work, that is a sign the battery is going bad.
-Most opener remotes use a CR2032 battery.
-Here is a video on how to test a GENIE remote battery • How to test & change a...
6:13 HOW TO PROGRAM THE REMOTE
-Push the 'Learn' button and then the remote button to link the remote to the opener. The lights will flash.
6:40 KEYPAD OPENER NOT WORKING WELL
-Replace the 9volt battery
7:12 How to set the HOMELINK built in car remote opener
Watch this video: • How to program your Ho...
7:30 SOMETIMES THE REMOTE OPENS THE DOOR AND SOMETIMES NOT
-If your remote only works when it is super close, the battery in the remote is bad or the antenna wire is broken or needs to be soldered.
Here is a video on repairing the solder joints: • How to fix a garage do...
-The main circuit-board may need to be replaced. Here is a video on how to do that: • How to swap a garage d...
-You may also be having LED interference. LED lightbulbs can emit a RF [radio frequency] that is in conflict with the RF that the remotes use.
9:54 Motor making weird noise or weird noise coming from unit and the door won't open or close
-Check the capacitor. If leaking it definitely needs to be replaced.
11:06 CHAIN IS HANGING OR DROOPING
-Check to see if the gear at the top broke. You cant reattach it, you will need to buy a new gear set. This is usually caused by a chain that is too tight but it could also be a result of a door that is not balanced. An unbalanced door is a result of a torsion spring failure.
-If the gear did not snap off you may have just a loose chain that needs to be put back on and tightened.
13:19 DOOR BALANCING TEST
-Close the door and pull the safety cord. You should be able to open and close the door with not much effort. The door should also be able to stay half open by itself.
15:12 DOOR NOT OPENING OR CLOSING WELL - TORSION SPRING
-Check to see if the spring has slipped off one end or broke in half
-You may need to adjust the spring. [not an easy job]
16:20 DOOR STARTS TO CLOSE BUT THEN REOPENS - TRACK ALIGNMENT
-Assuming the sensors have been checked, look to see if your tracks are out of alignment. I have a video on how to do that here: • Garage Door Repair - w...
17:05 CHAIN IS MAKING NOISE - TOO LOOSE
-Loose chains can cause damage to other parts. Tighten it just to the point that it is not hitting anything. Don't try to eliminate all the sag.
18:37 NOTHING WORKED, MY DOOR STILL HAS PROBLEMS
-Check for loose nuts and bolts. Try to find something that does not look right.
-Ask a question in the comment section about your specific problem and I will do my best to answer.
If your garage door is making a lot of noise you may just need to lubricate it or make some minor adjustments. Here is a video that addresses that: • How to fix a noisy Gar...

Пікірлер: 1 900

@loisdotcom 2 жыл бұрын

Thank you Adam. I am a recent widow. I'm no handyman. My garage door opener stopped working. I was ready to purchase and have a new one installed... but decided to watch your video first. From one of your tips, I went and checked the sensor. Yes, something stored in my garage had gotten moved and was blocking it. My garage door opener is actually working fine. You saved me a lot of time, trouble, and money! Thanks again!

@jeffreyburns7562 Жыл бұрын

Lol ll

@mikemcpeters7220 7 жыл бұрын

Thank you Adam. I especially appreciate how you started with the most common problems, and then escalated to the more severe. Within a couple minutes you got to my problem. My door would start to close, and would get a bout 2/3 rds of the way down before opening back up. I was able to override this by holding the wall mounted button down, thus indicating a bad sensor. I had absolutely no idea how to fix it, and contemplated buying a new system. At least I now have a place to start the repair. Thanks again.

@annien4639 4 жыл бұрын

An absolute charm to listen to. Thorough and simply and systematically explained. Great teacher with the right use of words and progressions towards possible problems. Thank you.

@mitch60mccoy 4 жыл бұрын

Impressed. Your approach is simple, straightforward, but thorough without being overwhelming. Nicely done

@pjjohnson6477 5 жыл бұрын

The video was amazing and I greatly appreciate the focus on the sensors. Although, you reference longer time with sensors in another episode, the little bit you covered solved my issue. THANK YOU!

@huffmac 4 жыл бұрын

You are my friend, Adam. Saw the part where you can override the sensor by holding down the wall button and the garage door was able to close! So good! Saved me the expense of a logic board. Funny that our tech didn't know that!

@mdesai007 3 жыл бұрын

I had the weirdest intermittent issue that started showing up a few weeks ago with the garage door openers suddenly not working after I exit the home but opening the door as expected when we return back to the house! Thanks to your video, was able to trace it back to the bulb that I changed in the opener a few weeks ago! Also, great tips as I went through a few of them to try and figure this out...

@richlampman1332 5 жыл бұрын

Adam you are a natural teacher. This video is much better than any manufacturer's video by far! Thanks for the info!

@barbid1951 7 жыл бұрын

Wonderful video with great and simple instructions! It's seldom that I can watch a video on troubleshooting and be able to completely understand the step by step instructions the very first time, if at all. This was very easy! Thank you for making my day!

@IvanDeSousaJR 7 жыл бұрын

Hey, I see this video was posted 2 years ago, but you hit right on the problem I had with my opener. I just watched it today, went to my opener and boom! Fixed! Thanks and keep this video up. For sure it will keep on helping people in the future!

@SP-ii6ji 4 жыл бұрын

You are right about the sensors! I already left a message for the repair guy. Then I saw your youtube video and checked the sensors, the snow shovel was blocking it, I didn't notice it because it was dark. Saved me a service call! Thanks for your great video!

@Sundayschoolnetwork 2 жыл бұрын

Oh my goodness, I just cleaned my sensors and it's working! Thank you so much! I had called a garage door company today. He came out and said I needed a new unit. It was going to cost almost $500. He never even tried to troubleshoot the problem. Thank you again!!

@greenleafd724 8 жыл бұрын

Awesome video. Thanks. After I checked everything else. I popped the cover. There was goop all over the inside bottom portion of the cover. The opener is 20 years old, so I knew at that point that the capacitor had blown. $24 later and I am back in business. No service call. You saved me some cash.

@michelletobin9754 5 жыл бұрын

QUESTION: MY GARAGE DOOR OPENER WORKS WITH THE HARDWIRED BUTTON, THE REMOTE, BUT NOT THE KEYPAD. REPLACED THE BATTERY..... NOTHING!! HOW TO FIX KEYPAD??? HELP????

@Carluchs 4 жыл бұрын

Hey!! I have the same issue!! How did you fix ir!!! Thaaaaankssss

@av2551 Жыл бұрын

Did your capacitor itself appear normal (not swollen or busted)? I’m facing this also. Opened it up, looked around and realized/felt there was white goop on the bottom/on the white gear and immediately thought capacitor issue. However, could it be grease instead?

@av2551 Жыл бұрын

@@Carluchs did you fix your issue?

@patrickwilliams5465 9 жыл бұрын

great video Adam, thanks. I saw the torsion spring on my garage door busted in half. Watching your video explained that that spring could have been the problem why my door would not shut down all the way. It stays up 3-4 inches off the ground. I'm not going to mess with that torsion spring so I guess I'm going to have to pay for a garage door repairman to fix it. At least I know what's the problem thanks to your video.

@doddanand 2 жыл бұрын

Thanks! What I liked about this video was, there is no BS and you focus on the essentials. Was worth every minute of my time watching it and of course helpful!

@marcdevinci893 6 жыл бұрын

Thanks Adam for the thorough walk through. My garage did not close easily when leaving in the morning. Required multiple attempts with remote had to fiddle with it for several minutes but would work fine when coming home. The culprit = LED light bulbs I put in there recently that appear to interfere with remote signal. Makes sense lights are off when I come home but on when I open the garage door to leave in the morning. Saved me a repair call!

@justineestell7869 8 жыл бұрын

Thank you so much, Adam!!! Your video helped me discover that our garage door was 'locked' and that is why the remotes weren't working!! I LOVE that you saved us a phone call to a professional. Thank you, thank you!!!! You explain things so well!

@macross25 8 жыл бұрын

This video was very helpful. I cleaned off and checked my sensors. Sure enough they were slightly out of whack , a quick adjustment and all is good! Thank you for posting this!!!

@ultimateelectricltd.4916 4 жыл бұрын

Yeah, me too. Electrician here, who assumed it was a failed component in the motor control or relay or some such electrical pain in the neck. I had no previous experience of garage doors, but this video made it a very simple fix. Saved me a lot of time so top bloke for posting Adam, thank you.

@charlesjones6686 4 жыл бұрын

chain jumps off while door is on b its way up

@navijohal2025 4 жыл бұрын

@dorothykaufman2035 3 жыл бұрын

@@ultimateelectricltd.4916 1

@ronniemo_1622 2 жыл бұрын

Thank you for putting in the time to create this video. I have gone through a bunch of steps, but the chain is not moving when I press the button. It makes a grinding sound(pretty loud). Is there a way to make sure the chain is not locKed/frozen in place?

@debbieschuessler9605 5 жыл бұрын

Thank you so much, Adam! After two weeks of my remote not working, I only had to watch the first tiny bit of your video to fix the problem myself! The “lock” button on the wall box did not say “lock” so I didn’t even know what that button was. I pushed it and viola! The blinking LED stopped blinking and my remote now works! Yay! So convenient to be able to use my remote again! Tanks to YOU! 😊 - signed, 66 year old single lady.

@ronaldwolf2599 4 жыл бұрын

You nailed it! My wife hit the wire going into the unit with a broom. As soon as I moved the input wire, the led light came on. Works perfect! Thank again.

@nathanschnieder470 4 жыл бұрын

Thank you so much AdamDIY!!! You helped me fix my problem. Sensor wire was loose and needed to be tightened. Now the sensors work and the garage door now functions properly!!! Appreciate your help!

@Dawn-S 3 жыл бұрын

I thought the sensor light was to stay on always. Ours, Liftmaster, only comes on when we push the buttons on our remotes. Then I’ve figured out that the one sensor needed to be tightened. Thank you for your teaching! It was thorough and fabulous!!

@ruthkotwica3334 4 жыл бұрын

Thanks, Adam. Just a simple adjustment to the sensors postitions and, like magic, my garage door is staying closed. Thanks again!!!

@spiceytradeboat8893 Жыл бұрын

That was a really great video explaining all that goes on in a common garage door. Well paced, explained, thorough. Feel like a pro! Thanks

@taylorhead9842 6 жыл бұрын

Adam, just wanted to say thanks you helped me fix my issue. My sensor must have kicked and got out of alignment. You're the man, thanks again for the helpful video!

@dukecarlisle5096 6 жыл бұрын

This was the BEST diy repair video I have seen: solved our problem easily with no cost. Thank you, Adam.

@Starcraftowns99 3 жыл бұрын

Great video. Love the way you explain things in a calm and steady manner without going on foot too long. I have an issue ( forget sensors for a sec) where the door will completely close, but then opens right away. Its not a sensor issue because blocking sensors makes it reopen midway and lights flash. So its not a sensor issue. Why does it not stay closed? I guess the question is, what part tells it, you have reached the bottom, stay there. Much thanks.

@lafeedulogis9589 Жыл бұрын

Wow🌟 Thank you Adam! In 20mn I understood correctly! You are perfectly structured with a good diction, clearly pronounced and explaining from simple to more complex troubles. I successfully realigned my sensors. Thanks 🇺🇸 You made my day, saving me a lot of time and money.

@samklein9374 4 жыл бұрын

Thank you for this VERY informative video. We had a "sensor" problem; neither light was on... So, I took your advice and EUREKA, the two common leads had come loose! Cleaned and reinserted wires, all's good. Thanks again.

@tingachang 5 жыл бұрын

I was able to Identify and fix my problem right away after watching this. Great troubleshooting video. Saved myself $89 for the garage pros to come take a look. Thank you!

@113MPG 6 жыл бұрын

Thanks for all that. It was very helpful. I had an issue closing the door. It would go down some of the way, then stop and turn back. The fix was the turn the blue button clockwise to be less sensitive. This made it overcome the slight pressure on the turn when closing an open garage door. Easy fix.

@GreenDawn8993 5 жыл бұрын

Adam, thank you for a comprehensive, and detailed Video clip. Our previous Home had a Chamberlain opener (which I installed myself). It did not function one day, so I examined the Laser units and found that one strand of a Spider's web was causing the problem. We now have a Genie opener; however, the Learn Button fails to function when depressed; thus, the L E D light fails to illuminate....accordingly I can not program my new remote controls.

@crescentcarol 7 жыл бұрын

My lens was dirty. Thank you! Saved me a service call on a Holiday Weekend!

@razijun5272 6 жыл бұрын

Thank you very much for extremely comprehensive instruction. Can you please help me understand what causes the garage door opener not respond, but after unplug, and plunging back (reset) starts working for few days, and gets unresponsive again.

@shubhanggupta8833 3 жыл бұрын

Where has this product been all my life?! Works like a charm!

@psanscartier 6 жыл бұрын

Thank you so much. I had been troubleshooting my garage door opener for a few weeks, I even contacted Chamberlain support, but they kept giving bogus answers about extreme cold. And then I clued in when you mentioned LED Bulbs could interfere with the signal. Removed the LED bulb, works like a charm now!

@michaelwalling8281 3 жыл бұрын

Thank-you so much for doing this video. That is my exact opener and now I'm pretty sure the sensor beams are at fault. You and You-tube are awesome.

@KevinStJohn-zp9by 8 жыл бұрын

YOU ARE THE BEST! Just fixed my sensor! Saved me a service call! Thank you!

@AdamDIY 8 жыл бұрын

+Kevin St. John That's great! Glad to be of help.

@robt2625 5 жыл бұрын

AdamDIY Hey Adam, I have a Liftmaster 1/2 Hp belt drive formula 1. Model 2280R. Produced in 2005. I have a 1 width double wide garage door with individual slats (4). I performed a garage door balance test opening the door disconnected from the release cord and raised the door to 4-5' and held the door at that height and door and slowly release the door and let go of the door and immediately started free falling to the close position. That means the door is not balanced.

@robt2625 5 жыл бұрын

How to balance the door

@bosschichi 4 жыл бұрын

@@AdamDIY Hey Adam, what if a door starts going up and then stops. Press button again and it does it again. Gets to half way and stops? Just wont do a clean run up anymore :-/

@melissagreen_ Жыл бұрын

You had me at the very first issue, check the power! OMG it seems so obvious but I had completely forgotten that I clicked the power off at the wall, by mistake a little while ago and this simple thing was causing the problem. Thank you for putting this first on your list of issues, sometimes it's the most obvious things that we miss, but I just saved myself a whole lot of issues (and money) as I am unable to afford to get someone out to fix it at this time. Your video is a God send and much appreciated.

@michellethomas6199 3 жыл бұрын

Thank you so much for this video! I moved a box in my garage and knew I hit something to cause my garage door to malfunction, but didn't know what it was. After watching the video, at 4:16 or before, I went out to check my sensors and sure enough, one was them was knocked out of line. I lined up the one and my garage let down like normal! I truly appreciate you for this.

@tbHighlandRider 5 жыл бұрын

Thank you Adam, I really appreciate your effort! I was going nuts about the garage door remotes not opening consistently, had to press it at least 20 times till it opened, sometimes never opened and sometime opened at once, Yes it was the LED bulb causing the problem. Now no issues. Thanks again !!!

@minr6851 3 жыл бұрын

Thank you so much for putting this for us. I just fixed our door and my husband promised me to pay $400 for it!!! Sometimes it’s such a simple thing but we ordinarily people don’t know anything so call someone and wait for days and pay fortune for it. Very appreciate your time and knowledge...

@dranet47 5 жыл бұрын

Thank you!!! We've been having so many problems with our remotes not working that we were getting ready to replace the whole thing. When you mentioned LED lights interfering, I realized I stuck an LED bulb in there a few months ago. I took it out and put in a fluorescent bulb (which I don't like, grr) and now the remotes are working perfectly. Again, thanks! You saved me a lot of money.

@michaeljfrederick9920 4 жыл бұрын

Thank you Thank you Thank you! I would have never thought that my new LED bulbs would be the cause! My garage door would open but would not close for both cars using homelink. I had to resort to my original hand held opener and hold it directly under the antenna to get it to close, then run out to the car while avoiding the laser beam. I checked everything, reprogrammed both car remotes, unplugged the unit to clear the memory, nothing was obstructing the door, etc. and nothing worked. I was getting ready to check/replace the antenna when I came across your video and decided to replace the lightbulbs and go back to CFLs. It worked with no problem! This is probably becoming more and more common as people move to LEDs.

@amdjvd 8 жыл бұрын

Thanks........... I had a sensor issue. This video saved me a lot of money.

@raymondsmith4541 8 жыл бұрын

Thank you Adam! Problem solved! It's been more then a year, I thought I needed a new unit! It would stall and retract!

@intruder01lc 6 жыл бұрын

Thanks Adam. I wish I had looked at the video before I attempted to fix my problem. I now realize I have a sensor alignment problem and unfortunately I have to recode my remotes as well.

@TheRawChuck 4 жыл бұрын

Thanks for these videos. I was at a loss as to what is wrong with our garage door and this helped me find the problem. The details in the video and description are very helpful.

@lindabarnes1585 5 жыл бұрын

You have described every conceivable problem in such great detail and saved us the cost of a garage door tech visit. Thanks so much. Great video.

@EdwoodCA Жыл бұрын

I was hoping he would cover where the sensor wires connect to the motor unit. Not just if they're loose, but which ones go where... in case they got mixed up by someone else trying to troubleshoot an issue. As well as, a way to troubleshoot to verify if a wire was broken internally with no obvious cuts to the outer insulation. So yes, nearly every conceivable issue... but not everything. He also didn't go over travel distance for opening/closing, nor the sensitivity adjustments for opening/closing force. If those are too far out of whack, doors often will stop and reverse believing they've hit a obstruction.

@stuartleis9079 5 жыл бұрын

Great video. I have that exact door opener and it quit. This gives me several ideas of what to look for. Very thorough and helpful. Thanks.

@nealeskauge4197 5 жыл бұрын

Thanks! Great video. I replaced the weatherstrip on my door and now it goes down about 75% and then reverses to open. I removed one side of the weatherstrip and the door works fine without it attached.

@Rhygoo1 Ай бұрын

Thank you Adam, just got a very little “I don’t even think about that “ problem. The second tip of yours about blocking/unblocking the remote worked. So I am very satisfied. Thanks again

@catherinecrawford2289 4 жыл бұрын

YES!!!! Single Mom fixes another household device thanks to You Tube! You're the best!

@jz5875 4 жыл бұрын

Thank you so so much, I fixed my garage door. The sensor was blocked by a leaf, but I did not know. After I watched your video, I checked the sensor and found the leaf on the sensor lens and now all works.

@paulhansen5053 Жыл бұрын

Yet another success story. I replaced the rollers and must have bumped the sensor sideways, so that it "sort of" worked, but mostly not. Thanks to your video I was able to notice the problem, realign the sensors, and now it works fine!

@8890880 5 жыл бұрын

Thanks for being so detailed. Mine ended up being a wiring issue on the green light sensor. I’m sure I did it cleaning out the garage yesterday

@SertEngineering 6 жыл бұрын

Such a good job. Appreciated. Thank you for video.

@Robmuniz1 8 жыл бұрын

This is one of the best explained videos I've seen about garage door openers troubleshooting! Thanks!

@arnoldmcneil1304 3 жыл бұрын

Amen to that,.I had a lot of malfunction. You explained what had to be done so well. P.s. my wife thinks I'm a genius. I'm 83 and I fixed our garage door.

@62mry Жыл бұрын

Hello. When watching your video, one of the things that helped me was seeing how the release cable worked. I own a rental property and one of my tenants, in spite due to being evicted, disconnected the arm that attaches to the garage door. Which is also a part of the release handle. So seeing how the arm worked, helped me troubleshoot the problem and now I can fix it. So thank you for all of the added information as well.

@dalcer1 Жыл бұрын

My Chamberlain opener would not let the door come down .. just CLICKS! I had called a service company to come .. $$$$$! Thank you ADAM!! Your troubleshooting video saved me a ton of bucks on a Saturday! I was able to detect 10 flashing lights indicating the Reverse Sensor was not functioning .. then I found that the SENSOR WIRE WAS CUT IN TWO!! No sensor lights were on! I pulled the 110v plug to kill the power. I cut the wire in two where it was damaged, stripped the ends and remade them again and electrical taped them securely. PLUG BACK IN, BOTH SENSOR LIGHTS WERE NOW ON .. ! Put the ladder away and VOILA~ the door was working perfectly again! THUMBS UP!!! George D.

@simplyvg 5 жыл бұрын

I had tried so many fixes to my garage door before watching this video and figuring out that an LED bulb was causing erratic garage remote behavior. thanks a ton my friend.

@AFEWS 7 жыл бұрын

Tried using LED bulbs which made remote malfunction. Thanks to your video, we replaced them and now remote works fine!

@dvdprodave54 3 жыл бұрын

Very good, very clear, well done! One suggestion that others MAY have already made: I would put the section about checking the torsion spring at the START of the video! (You now have it starting at about 12:30.) In my many years of home ownership, that has been the problem twice, and with a broken torsion spring, "you ain't goin' nowhere!" In fact, if it is broken, you can easily strip the gears of your garage door opener by trying, repeatedly, to get it to work. And, of course, if the torsion spring is broken, you NEED to call in an EXPERT repairman! Thanks.

@Kili-mo-money 5 жыл бұрын

This is one of the best diy videos I have seen on KZfaq. Thanks so much!

@thufirhawatt8737 9 жыл бұрын

This helped. Thanks for taking the time to make it.

@andrewelsbree2508 4 жыл бұрын

Thufir Hawatt has

@dragonbud0 7 жыл бұрын

Thank you for taking the time to explain. It helped me to debug my Genie door opener.

@USdefender1 2 жыл бұрын

I thought this was going to be in excruciating boring video, but I had to watch it because I needed to adjust my door. I couldn't believe it, but you actually made this video so interesting it seems like only 4 or 5 minutes had passed before it was over. I felt like I was in garage door collage and you were the professor. Thanks for this valuable information.

@joanneanderson6535 2 жыл бұрын

TY sooooo much. Us ole ladies w/ out husband's can have many problems. One of my ground fault plugs in garage had tripped and just pressed that button and all was on again. I'm so glad to have your little tips to get my mind going in the right direction.

@sherrysulochana7503 7 жыл бұрын

wow you saved us money, as your easy steps to trouble shoot helped me to find out what was the problem and yes i did it, with your help, I am proud, thanks a lot

@AdamDIY 7 жыл бұрын

Awesome! I'm glad to hear it.

@sherrysulochana7503 7 жыл бұрын

Nate Iikubo

@AdamDIY 7 жыл бұрын

Not everything is awesome. Some things are Wicked Awesome!

@IPas2System2014 6 жыл бұрын

+ogfre123 really exit?

@IPas2System2014 6 жыл бұрын

+ogfre123 really exiting?

@FathersRightsOrlando 7 жыл бұрын

Adam, thanks so much for the great video. I was able to follow the steps and figure out what was wrong with my garage door opener. Also, thank you for making such a high quality video. A real pleasure to watch!

@rothros 4 жыл бұрын

This is very helpful video. You are 100% correct of having LED interference. Low voltage LED landscape lightbulbs are emitted a radio frequency that is in conflict with the remote control.

@CamberHill 4 жыл бұрын

Your video just changed my 5 years of wondering what was wrong with my garage door opener. It's was the sensors. Thank you.

@curtiskekoa5095 5 жыл бұрын

9to5 - great video especially for "beginner" ... through knowledge in simple english and well done video. thanks.

@iTube855 9 жыл бұрын

Awesome video with many solutions. Thank You!

@malair3130 7 жыл бұрын

Amazing video. Just had to dust my sensors. We have been overiding the system, whenever the garage door wouldn't close. A big thank you.

@phdnjs19 5 жыл бұрын

Thanks Adam. I recently replaced the lights on the opener for LCD lights. I couldn’t figure out the problem was because the remote would only work in very close proximity. I tried during off my Bluetooth on my phone but that still didn’t work. After watching your video, I swapped out the LCD lights and wowla works again like new. Definitely saved me some money. Thanks again Adam!

@mohammadmahmoodi2696 8 жыл бұрын

thanks for your simple,easy and practical on truoble shooting info which anyone can do it.

@katja6667 8 жыл бұрын

found loose wire at sensor! thank you thank you!

@DipakPatel 5 жыл бұрын

Holy CRAP!! You're the best! I bought a Tesla and my garage door would work intermittently. They came out to the house and tried to fix it and the car's been in the shop twice now. After watching your video, the literal light bulb went off! I installed LED lights on the garage door opener the week i got the car. I bet its not related at all. I plan on swapping out with the old bulbs to see if it works again. Thank you so much for the help your video provided! You just saved me buying a new garage door opener!

@jeffsawyer2136 5 жыл бұрын

Very helpful video. My sensors were blocked, so it was a totally easy fix (move the broom out of the way). I kept watching though, because I learned a lot of other great stuff about these openers. Thanks!

@shoaibb8862 3 жыл бұрын

This was an awesome video that was to the point and covered everything I needed to know! It helped big time ...thanks!

@TheTeddon01 3 жыл бұрын

Thank you Sir. I got as far as the 5 minute mark and your insight that the bottom sensors were not aligned was dead on. Made sure the green light was solid at the bottom sensor (it was blinking green...) aimed it better until the light was solid green. My garage door is working again, Bad for days now. Thank you very much.

@megmoritz880 2 жыл бұрын

It was the flashing lock light...followed your instructions and it was fixed in 20 seconds. Thank you!!!

@temitopef 4 жыл бұрын

Thank you for this video it helped me solve a sensor problem that was stopping my garage door from closing.

@gailsaunders2708 5 жыл бұрын

Coding problem solved in eight minutes flat. Thank you. : )

@josephd5715 5 жыл бұрын

Grateful Adam, problem solved in the first 2 minutes 45 seconds. Thank-you!

@richardnash6613 5 жыл бұрын

Very well done sir, good overview of most of the potential problems that can cause door opener failure.

@RickHarrington4106 5 жыл бұрын

I too want to thank you for this excellent video. My garage door opener remotes suddenly quit working, but the keypad and wall button still worked OK. Checked batteries, wires, memory, sensors without success. Decided to check You Tube for help and ran across your video and BAM!!! there it was. You spoke of how LED lights in the unit can interfere with the signals from the remote openers. I remembered I had just put LED's in the opener. Replaced them with standard bulbs and all is well. You Rock!!

@ra3jualaga45adi 9 жыл бұрын

Thanks Adam, Great video, extremely helpful. Perhaps saved $100 this morning!

@AdamDIY 9 жыл бұрын

Raju Alagawadi Thats awesome!

@marthayounger9219 5 жыл бұрын

the control to my garage door opens the door but do not close the door?

@silviarandall3110 4 жыл бұрын

I was waiting for you to talk about the two buttons that rotate and have numbers and round arrows right and left and you never mention what they are for. Everything else was goodness

@rickjohnson7394 2 жыл бұрын

Adam, great video. My problem was door would only open at certain times and when you talked about the led bulb possibly blocking the signal, I replaced those bulb's with standard bulbs and all is working. Thanks so much for saving me a service call. Blessings to you

@hernanifreitas5998 4 жыл бұрын

Great video! After trying to figure out what was happening for over than an hour, watching the first 2:25 were enough to solve my problem.

@lilipadtx 8 жыл бұрын

Thanks so very much! Exactly the info I needed!

@alexjroberts80 8 жыл бұрын

I can't thank you enough for this wonderful video. God bless you

@mapleone6612 6 жыл бұрын

Thank you so much for sharing your knowledge with us.Very detailed and easy to understand. One quick question for you, if I may? My garage door sometimes opens by itself! Pretty scary, what causes it to open on its own? And what can I do to remedy this problem? Thank you very much for your time & effort, which is greatly appreciated.

@marklee3570 3 жыл бұрын

You helped me to fix it tonight. It's been bugging me for weeks. Thanks for putting this video together!

@ssalzone 8 жыл бұрын

LED Bulbs!!! That was the issue!!! i never would have thought that could be the cause. It was strange because the door would sometimes work and sometimes not. Now i know why: if the (LED) lights on the unit were on, it didn't work, if lights were off, it did work. Also, the button always worked because that's obviously hard wired. very interesting. thanks!!

@IAmNotAFunguy 3 жыл бұрын

They sell special "garage door opener LED bulbs" that use different radio frequencies.

@dallasdesi 8 жыл бұрын

Thank you so much . My problem got solved with in watching first 3:10 secs of your video. 😊

@edh656 Жыл бұрын

I cannot ask for more. thank you so much!!!! you could not be more precise on details and and techniques to repair.... Really really really good 👍👍👍👍

@kutlanozker3110 4 жыл бұрын

Thanks Adam, very informative and effective video. I clean my sensors both lights are solid. Door still does not close, it only closes when I hold the button.