Adapter bearing installation

Рет қаралды 223,809

SKF Parts Info

Күн бұрын

How to properly remove and replace an adapter bearing on a two-bolt flange.

Пікірлер: 47

@rodneytay3545 2 жыл бұрын

Fantastic. You know the old saying, "you don't know what you don't know" and it was definitely true in my case: I looked at my pillow blocks for hours trying to figure this out - and thinking that there was no way to press the bearings in without the cast iron pillow block housing exploding. I'm convinced your info just saved me no end of grief. Thank you!

@farnorth13 6 жыл бұрын

this video just saved us so much work....we didn't have any idea how to replace a similar bearing in a similar flange ..had no idea what those 2 grooves were for....went in smooth as could be for us once we knew the proper procedure Thank you !

@SKFPartsInfo 6 жыл бұрын

Glad it helped! Thanks for watching.

@kruppratte218 5 жыл бұрын

Thanks, I was wondering about that, I ended up using a handle off of a Broken Chain Disconnector, instead of a pry bar, but before I seen this video, I was going to beat it in with a hammer, I just installed my first bearing in a housing with no bearing in it, needed it as an Idle Gear shaft or a Slave gear shaft, I'm basically teaching myself Mechanical Engineering, videos like this are a huge help, saves a ton of money, time & effort, now just need to grease it & get a nipple cover I guess.

@simonkellen8178 3 жыл бұрын

you all prolly dont give a damn but does anybody know a tool to get back into an Instagram account?? I was dumb lost the account password. I would love any tips you can offer me.

@magnuslarry1455 3 жыл бұрын

@Simon Kellen Instablaster :)

@simonkellen8178 3 жыл бұрын

@Magnus Larry i really appreciate your reply. I got to the site thru google and Im in the hacking process atm. I see it takes quite some time so I will get back to you later with my results.

@simonkellen8178 3 жыл бұрын

@Magnus Larry it worked and I finally got access to my account again. Im so happy! Thank you so much, you really help me out!

@magnuslarry1455 3 жыл бұрын

@Simon Kellen You are welcome :D

@Mijanur96 6 жыл бұрын

Thanks...I learn how to open pilo block bearing from this video...

@electricaldrawing4067 2 жыл бұрын

Thanks for ur highly co-operation.

@PP.EKOTECH 2 ай бұрын

GOOD JOB ! :)

@MarkIrwin561 6 ай бұрын

Thank you, SKF ❤

@WilleJamesHuff Жыл бұрын

This video helped a lot. Thanks!

@g.zoltan 6 жыл бұрын

That design is really smart, strictly keeps the bearing in while it can still be removed, but does that also mean that the bearing can rotate in the housing? So when using this type of bearing unit, I need 2 of these to have a fixed axis dierction?

@SKFPartsInfo 6 жыл бұрын

The inner portion of the bearing rotates with the shaft. The type of equipment that you have determines how the ends are held and if you need more than one. Thanks for watching!

@kayacox5190 3 жыл бұрын

This was super helpful thank you

@telefoniafalsetta1982 3 жыл бұрын

Is this a self aligning bearing?

@user-hs9ie9vg6y 3 жыл бұрын

교육용 영상인가요? 샤프트 공차가 ㅎㅎ 일주일에 한번 문제 생길듯

@eliugonzalezmaldonado1860 5 жыл бұрын

Excelente explicación

@heinzbauer5528 3 жыл бұрын

Thank you!

@1think19 4 жыл бұрын

What about if the shaft doesn't come out like that how do u remove the bearing from the shaft when it's been there for ever

@SKFPartsInfo 4 жыл бұрын

Rust that develops over time can make the removal more challenging. Use a good rust penetrate several times. If that isn't enough to remove it then use heat.

@coltx64 5 жыл бұрын

what can i do if I don't have the grease machine you use? and what can I do to make the bearings roll easier? I have two UCP201 - UCP212

@SKFPartsInfo 4 жыл бұрын

A standard grease gun can be used in place of the battery powered Lincoln grease gun. If the bearing is not rolling easily make sure the shaft that the bearing is mounted to is in alignment and add addition grease as needed.

@aziznoureddine4705 5 жыл бұрын

Hello. Does it affect water and cause it to break or not

@SKFPartsInfo 5 жыл бұрын

The adapter bearing with their double or triple lips seals are very water resistant. If water does get into a bearing it can adversely affect its operation.

@aziznoureddine4705 5 жыл бұрын

Hi. Does the water affect the roller or not.

@SKFPartsInfo 5 жыл бұрын

The adapter bearing's double or triple lip seals are very water resistant. If water does get into a bearing it can adversely affect its operation.

@hyunjunlee8466 4 жыл бұрын

Thanks a lot!

@traevonsharp9976 2 жыл бұрын

🔥🔥

@lustatus 5 жыл бұрын

you gave it two pump of grease ; is that enough?

@mustafacalcuttawala4581 8 жыл бұрын

Is there any way to remove the seal of the adapter and expose the balls for cleaning ?

@SKFPartsInfo 8 жыл бұрын

Thanks for watching, the adapter bearing would not need to come apart for cleaning. Greasing the bearing will help maintain the longevity of the part. If the adapter bearing is making noise it may need replacement.

@mustafacalcuttawala4581 8 жыл бұрын

So what's the machine that you need for greasing it ?

@SKFPartsInfo 8 жыл бұрын

The machine used to grease the zerk fitting is a Lincoln 18 volt cordless grease gun. This is a good powerful handy grease gun, but other types of grease guns can be used. Also, depending on the needs or your adapter bearing, we offer non-relubricatable bearings

@shrileshmande8970 7 жыл бұрын

can we use a single bearing to support a shaft and which can take axial,radial as well as moment load?

@muhammadafzal8348 5 жыл бұрын

@@SKFPartsInfo how alligment motor and blowar pulley with bealt

@brentbarnhart5827 2 жыл бұрын

Did you MAKE SURE that was made by Allen? or was it just a Hex Head? LOL (Sorry, it took me decades to change my terminology.)

@weesupersteve 7 жыл бұрын

what size is the two bolt flange ?

@SKFPartsInfo 7 жыл бұрын

Thanks for watching. SKF supplies many different size bearing and flanges. The video shows an example of how the bearing fits into the two bolt flange and locks onto a shaft. If you need a specific size you can visit a local parts store or distributor that carries SKF premium bearings and they can provide you the correct part for your needs.

@weesupersteve 7 жыл бұрын

just wanted to make a pull up bar than can spin freely , and the one in the video looked perfect size

@miguelangelvalderrama1808 6 жыл бұрын

Those two holes are 7/16''.