Thank you for your videos. I have done quite a bit of programming (allen bradley, automation direct, and others) but i always like witching and learning new things. You do a great job of explaining. Thank you for your time and dedication.

Tim excelent video I highly appreciate yours support for showing it😀

Hi Tim, thank you for the information. Very useful video...

These videos are absolutely phenomenal! It's tutorials and explanations like these that have helped me teach myself these automation systems, so thank you so much for your time and effort here! I don't suppose you have plans to pull together a video similar to this one, expect using a Micro800 series with the PF525? I'm looking to control one using an 850, a PanelView, and a PF525...

Subscribed. Your a good man, I’m a fellow controls engineer. Work with AB on a daily basis.

Have made a sequel video to this? I would like to see an example of programming speed control setting up some of the other parameters. Also, can it be configured to use either ethernet or the push button/potentiometer? Love your videos by the way, they are the best ones I've found at explaining things.

Brilliantly done 🙏👍🏼

Tim, Thank you so much for share !!!! Im from Brazil

Thankyou soo much for the videos ❤❤

Thanks for the videos, your doing a great job. When we have to replace a drive that is networked to a Compact Logix via ethernet, we often have problems getting the drive to work with the system. Is there a video that you have that covers troubleshooting these problems? Thanks again

Awesome video Id be interested in seeing different speed set points and using the logic to change them (ie one button slow jog, second button fast jog)

Thank you very much for your answer boss! One more question is if I use wifi in a plant. How to set ip address to match plc inrslink?Could you make a viedo show?

its very interesting and informative video. thank you for making it

Very detailed information.thank you Sir

At 8:43 I noticed that you have three options for the start source (#46, 48, and 50). Number 50 is already set to E/IP. Did you have to change source one to E/IP or is there a way to simply select source three as your control method?

Thanks sir for this video, please share video on the use of sequence control in plant automation.

good explaination thank you sir .

I did same thing and I/O didn't come on at all it whould be nice to get video about it .Thank you

PARABENS PROFESSOR SOU BRASILEIRO VENDO TODOS SEUS VIDEOS E DANDO LIKES.

Tim, I love you videos but this one brings up a question. The two ways you show to turn on and turn off the drive produce the same result but the first one is instantly recognizable as on-off and the second must be interpreted you might say. To the average person the first is easier to understand. Green button turns it on, red button turns it off. The second example has a latch which is not needed, otherwise they are the same. Both take two rungs. What is the benefit of using the harder to read method?

Hi Tim, Thank you for knowledge you share. I have to replace on same 525vfd but different version ( old is version 1.6 and new one is version 4.0). After copying vfd program and connected to plc but Ethernet not connecting. But same vfd working with same Ethernet IP if i control from my PC

Great videos as always! If i am using a momentary foot pedal to control the powerflex can I use the start command in the "Jog" output instead of the start?

Thank you so much for the video, I have to make some changes to my data type the default data type doesn't have the actual current. what should I do to get actual current in the Input which are read from the VFD

Do you know generally how old the revision on the vfd can be until it stops communicating? Bc I think we had a power flex 525 with a revision 3 that went bad, replaced it with a 6 and didn’t communicate bc in the plc it was a 3.

Hi, thanks for all of your videos, really useful for me. Please could you tell me, how the plc keep the parameters for those inverters, I meanimg, we have a powerflex 225 burned out and we just set the IP on his HMI and all parameters was set and it works as built. How it happened? Thanks.

Thank you very much

Hi tim can you help me how to do configuration of two device ome master plc and other ethernet module via wireless anybus bolt wifi

I'd like to know if you could show us how to integrate a vision camera on a Controllogix or Micrologix over ethernet, please

Thanks Tim. good Video Do you have video tutorial to how to set up IP number of 1794 AENT and 1747 AENTR

Nice video.

how do i know which revision i have to put when im adding the drive? Thanks

Hi Tim, how can i record the Energy consumption of powerflex 525 to Studio 5000?

Thank you Sir🤝🤝🤝🤝

If my drive fails and I replace it do you have a vid on how to load the old parameters to it along with set up Ethernet connection?

Could you make a video on how to use the powerflex 525 VFD PID loop control function in studio 5000 using the compactlogix plc?

otimo ja me ajudou.

Hi TIM I am starting a new project with a 1769-L24ER controller. I connected up to the USB port and did a firmware flash to V21.011. Everything seemed to go normal. At the end the controller would not communicate back to the ControlFlash program that it had the new version. Now I get the solid red OK light and when I power it up it wont do the diagnostic test where it will runs through and lights all the lights. The USB port wont work either. Any ideas

HI Tim Your videos are great my question to you how do you connect and disconnect the 525 from within the studio 5000

How to change IP address in Power flex video-18?

Only have version 20 of studio 5000 / . Will trainer work with this version(20) If not I gotta go ccw 12 / micrologix 800 / logic theme but I rather compactlogix .... which is ideal but I cannot get the proper version new at work .... only service version its 789 so I don't think it's the right one to program and train with but I have a full version 20 pro

Hi, i would like to change a powerflex 525 installed for other new one, but after It's configured, the ethernet led port only flashing and not connect to the net to recive and manage the vfd via ethernet? thancks

Can you do a video explaining a power flex 525 path splicing failed splice path

Do you have a video on how I can control a VFD on a compact logix PLC that is connected to a different compact logix?

How about siemens like s7 1200 controlling thevspeed of vfd same like this video i hope you have video for s7 1200 siemens

Boss. When i meet two enthernet cards in plc with different ip address. Which ip address i should set up in my pc for matching? Thank you ceru much!

can i program a compact logix l32e with studio 5000 lite, (the 950$ version you were talking about) im going buy that version but i only have a compact logix l32e to practice on and dont know if they're compatible... also. i told my boss at hershey about your classes and hes very interested. we are waiting till they hire 2 more guys to set up classes for everyone. do you have a buisness email i can give to my boss incase he has any questions.

thansk you , please help me , i can't find 525 inveter and adding into app rslogix5000, how to find that. best regarsd

How can I get one of the trainer boards that you use in your videos and what's the price?

At 4:43, you mention downloading the program. What program? I put the parameters in the powerflex manually following your previous video. Was i supposed to write a simple start stop program and downloaded it to the controller? what should my output be? one more, can i delete the pwerflex drive and create one the way you show here. I wanted to delete it and start fresh but got a mesage"Are you sure you want this module and all og its child to be deleted?" sounds scary? Thanks for all of your informative videos. I am new to this and already have learned a lot by watching them. regards Ben E

good video i have a question i need to know how to get a micro 800 plc to set the powerflex drive parameters on power-up via ethernet/ip or dsi and if any additional hardware is required other than ethernet cables

I think PLC to PLC communication would be a great topic to cover.

boss .please show us asi gateway control in studio5000.tahnks a lot

hi TIM i am wonder can we program VFD BY RSL 500 software i looked at controller i didnt see thank you

awesome

Hi Tim, Thanks for the video. I have done all of the steps in it. I can ping my controller from my PC and when I check the ip address of the drive it is 192.168.1.12 in the same subnet as the controller 192.168.1.10 and my PC. But I am getting communication error when I click on the connection tab of the drive. Don't know why? Thanks again

I had many problems following this video i wanted to list some things for others who have the trainer and their Studio 5000 may have locked up and sent many errors to AB. I changed many things not 100% sure what did what. Program would not download deleted ethernet connection, only left ethernet IP active and changed to windows default driver. Took HMI out of run on config screen. The program seems to have problems with blank spaces on PLC and Drive descriptions. When downloaded I tried to double click on drive it stopped like yours but my powerflex connection was grayed out in use physical so i had to use project. Then I got error writing port 0 Parameter 122 value out of range. I clicked ok and then double clicked drive and all loaded properly. Also for others with trainer steps in video may not work for instance buttons on drive because this is already changed in drive to ethernet IP. Really not 100% sure how i got myself in so many problems but maybe some of these steps will help others

If the 525 is not on the list, how is it possible to add it?

Failed to splice the path errror PF525??

This is what I see more and more in the field. Most drives are controlled over ethernet

It gets fun when altering the mask ie 255.255.0.0