Advanced Mission Planning 02 - Medicine Delivery at Remote Location (Autonomous)

Рет қаралды 8,936

Жыл бұрын

Advanced Mission Planning:
Takeoff
Fly towards remote location
Land at remote location
Disarmed
Delay (10s)
Release medicine at remote location
Armed & Takeoff
Fly back to home
Land & Disarmed

Пікірлер: 62

@harirajan2092 Жыл бұрын

Very useful and Impressive.

@harshalkoli9864 7 ай бұрын

Nice work Karthik! Keep it up!

@karthikstechtime0910 7 ай бұрын

Thank you, brother..

@mr.koanti8035 Жыл бұрын

Amazing Work ..am working on same project 🔥🌚❤️

@karthikstechtime0910 Жыл бұрын

Best of luck

@jeffreyjacksonraj5928 Жыл бұрын

Super na ......keep going

@karthikstechtime0910 Жыл бұрын

Thank you so much

@vegasofficial2431 Жыл бұрын

Great…keep it up

@karthikstechtime0910 Жыл бұрын

Thanks..

@gregsmith2807 4 ай бұрын

Knarly!!

@torqueandthrottle6812 Ай бұрын

Hi bro , Kindly can u pin the components list and circuit diagram in the comments section or in the description. It would have been very helpful

@alperencetin Жыл бұрын

nice job

@karthikstechtime0910 Жыл бұрын

Thanks!

@antonishchenko7099 6 ай бұрын

great! What motors and controller do you use?

@karthikstechtime0910 6 ай бұрын

Pixhawk cube & Sunnysky motors..

@torqueandthrottle6812 2 ай бұрын

Very informative video brother. May I know which Pixhawk controller board (version) u have used?

@karthikstechtime0910 2 ай бұрын

Cube orange. Version - 4.0.3

@mr.koanti8035 Жыл бұрын

Can you provide me with servo wiring and its all config please? I will be very thankful sir

@karthikstechtime0910 Жыл бұрын

Hi.. Connect servo to any aux port on pixhawk then configure it. SERVO X to RC X. Servo no. to one of your RC channel.

@bluecavemen 3 ай бұрын

I'm still new to this. But no. 3 is unknown. The first question is why is it unknown with a value number mean? How did you know that it was supposed to be released. 2nd question is how did you create a device to grab and release?

@karthikstechtime0910 3 ай бұрын

The "Unknown" option allows for the addition of new commands that are not included in the standard command list. The value entered corresponds to the command ID for arming/disarming, as specified in the copter's version available in the library. The servo release command is then executed after the disarm command, followed by a delay command.

@Sakti0110-kn2zb Ай бұрын

Greetings from Indonesia Sir, i have some questions for my final college project, the project is Use Radiolink Pixhawk 2.4.8 for Semi Autonomous with Waypoint Plan mission drop the water balloons (means prototype from Extinguisher Balls), the question is, is the BEC or UBEC (like adapter) is necessary to use when i wiring servo through the same battery (just use 1 battery), sorry for my bad English 😅

@karthikstechtime0910 22 күн бұрын

karthikaeromodeller@gmail.com

@Umeshsingh-rq8rt 11 ай бұрын

Good work Kathik.But some of the settings which we have to do in full param list. Without that this autonomous mission can not be achieved.

@karthikstechtime0910 11 ай бұрын

Thanks. I have already done that settings..

@samuelwesley668 6 ай бұрын

@@karthikstechtime0910 could you please tell what all settings changes u have done and from next video it would you helpful if u add them. thanks a lott. love ur work

@Omkar_Srivastava 7 ай бұрын

Which motor did you guys used in this project

@karthikstechtime0910 7 ай бұрын

Sunnysky

@asadkhan-mq8ro 10 ай бұрын

can you share the details of payload drop mechanism device that you used in this demoinstration?

@karthikstechtime0910 10 ай бұрын

Servo is used to release the Payload, and it is connected to one of the auxiliary ports. Servo open/close command is added to the mission.

@asadkhan-mq8ro 10 ай бұрын

link of the servo device that you used@@karthikstechtime0910

@makenthirenselvam5821 Жыл бұрын

Na I am doing the same project to my college I am having some doubts. How can I approach you

@karthikstechtime0910 Жыл бұрын

karthikaeromodeller@gmail.com

@sasidharan4460 5 ай бұрын

Hi bro can we use pixhawk 2.4.8 to do atonomous flights like this ?

@karthikstechtime0910 5 ай бұрын

Yes.

@atadhitamilanyt4117 Жыл бұрын

Anna servo yepdi connet pandradhunu solungaa anna plzzz

@karthikstechtime0910 11 ай бұрын

Connect the servo to any one of the aux out and enable the respective SEROX_FUNCTION.

@desimemes1490 3 ай бұрын

Bruh great How much did you spend in total

@karthikstechtime0910 3 ай бұрын

It costs around 75k without the battery and the radio controller.

@JayGamzTV Ай бұрын

How many miles can go this from?

@karthikstechtime0910 22 күн бұрын

I just conducted a close-range test to confirm that the code is working properly. The range depends on your drone's radio system and its flight time.

@corrotwhispers_ 11 ай бұрын

One small doubt bro Can we control mass flow rate in nozzle using mission planner If yes how???

@karthikstechtime0910 11 ай бұрын

You mean flow rate, for agriculture sprayer drone?

@corrotwhispers_ 11 ай бұрын

Yep Mean flow rate

@corrotwhispers_ 11 ай бұрын

Like can we code/plan through mission planner so that it controls the flow through nozzle???

@antonyshani9705 4 ай бұрын

Hi broh how can i contact you? I have some doubts. Please reply

@karthikstechtime0910 4 ай бұрын

Karthikaeromodeller@gmail.com

@2TAJ 9 ай бұрын

How i can doing it for my university graduation project plz

@karthikstechtime0910 9 ай бұрын

This platform can be employed in various applications such as collecting samples in remote or inaccessible areas, delivering medicine or food autonomously or incorporating companion computers along with onboard camera (AI/ML) to perform specialized tasks.

@atadhitamilanyt4117 11 ай бұрын

Bro yeppdi servo pwm set pandradhu solunga bro plz

@karthikstechtime0910 10 ай бұрын

Manual: Go to full parameter list_Servo9 for Aux1(Connect servos on aux1) Change Min, Max values as you required.. Auto: While planning mission, add Do_Set_Servo & Enter PWM as it is required..

@atadhitamilanyt4117 4 ай бұрын

@@karthikstechtime0910 IN autonomous mode for do_set servo...how to give servo pwm values where it is?? plz ans bro

@atadhitamilanyt4117 Жыл бұрын

bro plx snd the github link i cant find it...thanks in advance

@karthikstechtime0910 Жыл бұрын

github.com/ArduPilot/mavlink/blob/master/message_definitions/v1.0/ardupilotmega.xml