Airforce Texan, Replacing the Hammer Spring

Рет қаралды 30,025

African Air Ordnance

7 жыл бұрын

Installing the Magnum hammer spring from www.africanairordnance.com

Пікірлер: 36

@V3g3t41987 2 жыл бұрын

after seeing this i can now confirm the hammer spring on my texan is indeed broken before 200 rounds were put through it. nice job pyramydair.

@the1stkim 3 жыл бұрын

excellent video!

@Tony-o1b Сағат бұрын

That spring would obviously have more compression BUT how do you control valve bounce with so much preload on the hammer?

@christophercullison9644 5 жыл бұрын

Are you putting the big piece of metal in then spring then tuner wheel?

@scottbolden1 4 жыл бұрын

Do you have any printed instructions on changing the hammer and spring?

@barrypate134 Жыл бұрын

Hey Jeremy I just bought your stainless steel carrying two for my 357 but the plastic piece that screws in behind the spring won't screw in into the stainless threads?

@AfricanAirOrdnance Жыл бұрын

Email sent

@gjtheozzybrazzocouple3622 2 жыл бұрын

Thanks, I have a 308 standard steel tank I want to Max out this guns capability.. 4500PSI -1L CF tank.. new valve.. new springs Can you tell me exactly what I need to buy I love this gun and want more shots and more power

@AfricanAirOrdnance 2 жыл бұрын

MOAV 2022 xl 308 Super Valve 4500 psi Heavy Hammer and Magnum Hammer Spring available at www.africanairordnance.com

@jonathanstaley3883 3 жыл бұрын

Thanks for the video guys. Just a question about dry firing it without the valve in place. Is it only with the upgraded spring that this happens? I dry fired my texan a few times with the factory hammer spring whilst I was rebuilding mine after shipping it seemed fine to me after working the mech from cocking to safety off and trigger pull to see that the me h was working properly before replacing the cover, trigger guard and pistol grip. Now I’m concerned I’ve damaged it...

@AfricanAirOrdnance 3 жыл бұрын

I would be concerned as doing this causes the 2 retaining screws to hit the hammer tube and they will shear off even on a factory set up

@maikolpinto1155 9 ай бұрын

Hello, I have a Texan Cal 357 rifle and I only hunt vermin on my farm. I would like my rifle to shoot 80g JSB pellets at about 750 to 800 fps. What do you recommend to achieve this?

@AfricanAirOrdnance 9 ай бұрын

I would say that the rife would achieve. without any modification at all a stock rifle can hit those numbers no problem

@garypitzer8729 2 жыл бұрын

Thank you for showing us this. This is the only video showing how to do this. I would love to see how to take off the pistol grip and trigger stuff. I couldn't get my cocking lever to come off even after taking out the 2 grub screws off the hammer housing. So what is the benefit of the hammer spring swap?

@myohmy111 2 жыл бұрын

There was an in-depth video on the whole procedure Gary. I saved it about 2 years ago, and for some damn reason it has been deleted! GRRRR!!

@garypitzer8729 2 жыл бұрын

@@myohmy111 Thanks for checking.

@lukes-uf4bc 4 жыл бұрын

Shietttt¡¡!! i broke 2 times the 2 little retained screws of the interior ....do u sell this 2 replace screws??

@AfricanAirOrdnance 4 жыл бұрын

This normally happens when the gun is fired without the bottle and Valve in place cause the 2 screws to shear off email me at africanairordnance@gmail.com

@stevenchilds8056 3 жыл бұрын

I'm struggling to figure out what part to push down on to release the hammer and hammerspring.

@andtheallstars 3 жыл бұрын

I had the same issue. what I found worked best was to remove the detent spring for the safety. Its the only spring which runs horizontal. Then it was easy to push it down and pull the hammer tube assembly out.

@stevenchilds8056 3 жыл бұрын

@@andtheallstars I figured it out. Still need to go to the range and chronograph the upgrade. I love AAO

@gerardomonckeberg6606 6 жыл бұрын

Dear friends of AAO, changing the HS of my texan and keeping my 3000psi bottle will damage my rifle?