Correction the liner oring are 4.42 X 2.62mm. The single groove on the liner indicate the breech end .25 and .30 don’t have the oring on the 1/2” 20 jam sleeve.
Пікірлер: 50
@AirgunFunAddict2 жыл бұрын
Hi Ernest, great stuff! One thing I found very difficult to do was to get the o-rings back in the right spot, they want to bunch up. I tried the carbon fiber sleeve but it didn't work well for accuracy. I went back to the o-rings and found it to be highly effective for getting the o-rings into place! Works great for that!
@BullseyeBob5 жыл бұрын
Thank you Ernest. I just removed the 500mm sleeve last night....will put a 600mm sleeve on it with slug liner. Lots of guys leave the liner O-rings off but I have always had good results with them on. I appreciate the tips on tightening, use of locktite, etc. Thank you!
@jennysok5 жыл бұрын
AirGunner Bob_O where can you get sleeve for 600mm barrel?
@BullseyeBob5 жыл бұрын
@@jennysok I have a 25 caliber barrel kit that I'm using to swap sleeves. As if right now you can't buy a sleeve separately u less you happen to find one from a private party.
@aronkeylfb0235 жыл бұрын
Hi friend. I want to know please if a fax barrel hits x. can be adjusted to a youngest marauder. Please can you help me. I want to make this modification in a marauder
@BullseyeBob5 жыл бұрын
@@aronkeylfb023 What do you mean hits X? It will not drop right into any other gun. You will ha e to modify it to fit if that's even a possibility.
@aronkeylfb0235 жыл бұрын
@@BullseyeBob I'm going to make the modification I have a friend who made me the modified breech for this barrel. thank you very much for helping me friend
@paulandrews37853 жыл бұрын
thanks for the great video now I know how to service my barrel kit. 😉
@charlespeffley5 жыл бұрын
Hey Ernest you skipped right over how to install the o-ring inside the silver sleeve that keeps the barrel liner centered!
@BullseyeBob5 жыл бұрын
It's easy to install....fits right into a groove. Installation is similar to the breech oring.
@ptescreen183 жыл бұрын
AirGunner Bob_O I can’t see this oring in mine , strange
@fredcarter7003 Жыл бұрын
Can you do an update video for the new style barrels
@Jeeper137810 ай бұрын
Help i had my hunter compact apart cleaning it up. Put it all back together and had a huge poi shift. Probably should of market the position before removing the sleeve. Any advice ? Was thinking spinning the liner in 1/4’s and seeing if it shoots close to where it was ?
@ptescreen183 жыл бұрын
I can’t see any oring in the lock Nutt part , and when I did order that Oring and put it in the barrel lock Nutt it just compressed it and pushed it out the end
@edosan-airguns9265 жыл бұрын
As usual, great video, thanks! Saludos, Eduardo
@IntensoX223 жыл бұрын
Hey I looked at the drawing by FX there the 8x1 O-ring is going between stainless and brass not on the end that you are showing. i have the suspicion that my dreamlite is missing that O-ring way to easy Liner push in. And the Liner rings are pushed all the way to the end by shot pressure.
@scottbasham625 жыл бұрын
So that's where the thin o-ring came from. I didn't shoot mine out but my last liner change it came out with the barrel o-rings. I guess it's time to pull the whole assembly out of mt Wildcat MKII and get that tiny o-ring back in. So the liner o-rings for the 22 cal are 4.62 X 2.62 right? When I bought both pellet and slug liners they didn't come with o-rings.
@marcegrecco533 жыл бұрын
Thank you sir
@jp8351 Жыл бұрын
Hi How do you remove the stainless adapter from the tube? it feels glued on my M3. I need to remove it as the seal inside it came out with the other 3 o rings :(.
@raultamez13322 жыл бұрын
Sr I have a cuestion where can I get the jam nut part for my fx m3 .22 thank you
@aronkeylfb0235 жыл бұрын
I already have my barrel .25 STX 600mm. but it's very long I do not like the rifle so long it does not look good for my taste. Can you help me and tell me if I can cut it and put it 18 "of that size I would like my STX, please someone who can help me
@riazpatel52965 жыл бұрын
Can we have the internal oring size for the stainless steel adaptor on the .25? is it the same as on the .22?
@BullseyeBob5 жыл бұрын
I don't know the size. Contact FX-USA to be sure.
@worker20044 жыл бұрын
I screwed the nut that holds the liner in place "not tight" and now it is at the end inside of my moderator and i can't get it out.... So i can't tighten the liner properly. How do i get the endcap off of the shroud so i can take the nut off with it?
@je84223775 жыл бұрын
I would like to install a 500mm STX barrel from a Dreamline to my Streamline. Can it be done and work? Nice instructional video 👍🏽
@BullseyeBob5 жыл бұрын
I don't think it's a direct fit.
@mytube36874 жыл бұрын
I have an old fx wildcat 0.22 . Is it possible to replace the barrel with fx STX barrel?.
@am2am2am2am4 жыл бұрын
Hi,I have been asking if I could buy and install STX Barrel liner in to my Wildcat MK1,using one from MK2? Please if you find minute of your time to answer I would like to have one
@gorankovacevic16695 жыл бұрын
Nice video Like to see about AMP regulator video from Ernest
@BullseyeBob5 жыл бұрын
I have no plans to make a video on the regulator. Ernest Rowe has videos on that.....FX Masterclass
@nsboost Жыл бұрын
The 8x1 o ring that you don't have a tool for. How and where exactly does it go in? My impact is missing that o ring and I'm trying to figure out how to put it in. Mine is a .25 so its a 9x1
@jp8351 Жыл бұрын
I also would be needing the info on how to taking the barrel apart and replacing that o ring
@nsboost Жыл бұрын
@@jp8351 unscrew the shroud by grabbing it with your hands and spin it off.. use a crescent wrench or box end wrench to unscrew the threaded part in the end of the barrel. Then remove the Allen headed set screw at the back of the barrel where is slides into the block. Then pull on the barrel and it will slide out. Then you will have to unscrew the barrel sleeve from the barrel inlet/brass fitting.
@nsboost Жыл бұрын
@@jp8351 You can pull the barrel liner out before you pull the set screw. But that's kinda up to you
@jp8351 Жыл бұрын
Stainless part feels glued. Did you have to use a lot of heat to undo the stainless part? Or am I wrong on the glue part?
@jp8351 Жыл бұрын
got the stainless part and the tube undone. Used a micro welding torch (dremel versatip) went super fast and easy :). also found a easy way to clamp that part in a vise without scratching it, I use some aluminum foil wrapped fairly thick around the stainless/brass part. zero scratched :)
@aronkeylfb0235 жыл бұрын
Hi friend. I want to know please if a fax barrel hits x. can be adjusted to a youngest marauder. Please can you help me. I want to make this modification in a marauder
@whatfor55 жыл бұрын
What is the torque specification for the jam nut?
@BullseyeBob5 жыл бұрын
There is no torque spec that I know if. Make it snug but not tight. I normally do it hand-tight and then another 1/8th turn with a wrench.
@visionarytv37734 жыл бұрын
Sir, how to change inside chamber o ring ?
@derivas0075 жыл бұрын
hey ernest. could you say me the od size of this barrel/?? i would like to machin one for my airforce