often , japanese hornets show up when i've spilled some gas . they must be after ethanol too .
@thedoubtfultechnician8067 Жыл бұрын
I like my hornets like I like my mowers. Domestic.
@RK-kn1ud Жыл бұрын
Replace them with some cheap aluminum fuel cells (some fabrication required) and never worry about it again!
@paulmcgrath217513 күн бұрын
Late to the party, but why not rig holders for a pair of marine tanks? They are common and relatively cheap. Come to think of it, you could cut the top halfs off and use them as a base to build a holder from.
@PatrickBaptist3 күн бұрын
Your-A-Peein? You know what I wonder IF that is why my weed wacker take is leaking..... Thanks for the video I gotta go look closer.
@miken8001 Жыл бұрын
Would very much like to see a video on the smoke machine. would alsolove to build one.
@dankirkpatrick3326 Жыл бұрын
Could you coat them in truck bed liner, or garage floor epoxy coating? Or maybe plastic dip?
@ville1981 Жыл бұрын
What happened to the F525!? I loved that one, specially it's rough terrain capabilities.😄
@thedoubtfultechnician8067 Жыл бұрын
Still mowing with that too!
@geniusanthony10 ай бұрын
This probably doesn't help at this point but, earlier this year I ran a test with different types of epoxy submerged in E85. After months the West System G-flex was still solid where the others have long since turned to jelly or become brittle.
@thedoubtfultechnician806710 ай бұрын
Good information for the future!
@dannygoldman8216 Жыл бұрын
Hilarious as usual. Love the videos.
@croden94058 күн бұрын
Would ethanol free gas stop the beetles trying to get into the tanks?
@robertoruiz7069 Жыл бұрын
Funny vid and very informative i like it.Good repair job,tanks like that may only be under pressure when the gas heats up from the sun hitting on it.But at the current cost of new tanks i would look at just buying a ten gallon aluminum tank for a race car setup just cheaper.I'll start watching your channel it appears to be good.keep going.
@thedoubtfultechnician8067 Жыл бұрын
I’m considering dual Harley Davidson motorcycle tanks with flames painted on.
@bootblacking9 күн бұрын
Doing forensics in your church pants, rookie mistake
@davedemo8229 Жыл бұрын
I go 60 miles for non eth gas. Havnt touched a carb since. btw do a video on the smoke machine. would love to build one.
@thedoubtfultechnician8067 Жыл бұрын
Let me figure out how to keep it from exploding before I share the design…
@davedemo8229 Жыл бұрын
@@thedoubtfultechnician8067 aw come on safety is overrated
@djrenault Жыл бұрын
@@davedemo8229 safety third!
@Redneck078411 ай бұрын
JB Plasti Weld woulda worked better
@willwobs70306 ай бұрын
try fiberglass
@SSJIndy Жыл бұрын
I think I would have just taped the holes over and put some Red-Kote tank sealer in (after a good interior cleaning, of course.
@thedoubtfultechnician8067 Жыл бұрын
Isn’t that just for metal tanks?
@SSJIndy Жыл бұрын
@@thedoubtfultechnician8067 Don’t see any reason it would matter. It’s a tough, thick lining either way.
@thedoubtfultechnician8067 Жыл бұрын
Guess it depends on how it adheres to the plastic. I’ve used it with great success on my atv, but that’s a metal tank.
@hillppari6 күн бұрын
ethanol is the antiknocking agent. its not used for its energy content. would coud use something even more expensive or cheaper like lead lol