Nice 170 ! Thanks for sharing, enjoyed watching!

Thx 4 sharing Mr.Pete, always enjoy Ur videos & if it's about orange all the better.

That tractor sounds great! A year in the shop and you ought to have a handy tractor around the farm...👍

I have a d17 series 4 that needs a lot of work. So if they're similar, this will be educational.

Nice handy tractor for sure. If you want it to sound even better buy the original Nelson from AW Tractor in Cecil Wisconsin. He is the only place that has them. As far as the grill, there are rubber bumpers that go in the front that the grill pushes up against. If those are bad or missing the grill will fall off. Grills for 170s are worth big $$$. As far as bumpers, Agco still has them available. The dealer in Fort Atkinson Iowa stocks them I believe. I used to work there. I'm guessing Scott Imp would have them too.

👍👏👏👏

That Allis Chalmers 170 should make for a good series of repair videos this winter for us. Hope you have a safe & bountiful harvest. ROCK ON FARMER PETE!!!!!!

That should keep you entertained this winter, fun project will get you a nice addition to the farm. You can’t have to many tractors.👍

Good day Pete. Boy that does run nice! That will be quite a job, tearing whole rear end down.. That should be interesting. Thanks

great tractor!! mechanic told me one of the hardest things to do to that transmision was to pull the torque back in low sjde in road gear with a loaded wagon!! it puts a strain on the transmion. causing them to jump out of 4th gear. he said tractors on flat land didnt bother like tractors that came from hilly country. l should say using low side to slow down ground speed!! l be watchin!!!

Man yeah Mr Pete, looking fwd to seeing the 170 get repaired over the winter! "Enough to keep me out of mischief" 😁😁😁 I can see what you mean with the shifter on the old top plate 😳😳😳 Hope you get to harvest soon, looking fwd to the crop inspection too! Thank you sir for bringing us along, looking fwd to more !! 🇺🇸🇺🇸🇺🇸😁😁😁👍👍👍🌽🌽🌽

Looks like a great winter project. I'm looking forward to seeing it happen. I posted a winter project on my channel but don't have a heated shop to work in so probably ( ?) won't get a lot done on it but did start today as it was warm and sunny. Thanks for sharing!

That will be an awesome tractor. Allis isn't my favorite ‼️

Can't wait to see you fixing it up.

Great project tractor - should be a real solid performer by the time you finish. We just went through a troubleshooting project on our 170 gas, to find that the ballast resistor was intermittent. It would work well, then just stall out under load as though the gas or ignition cut out. Wait a bit and it would work again for months. Finally got so bad that we could detect by wiggling the resistor. Because the open iron windings can be exposed to the humidity, the rust slowly ruins it. We're looking at replacing with a modern sealed resistor to fix the problem permanently. It has 7000-some hours also and just keeps on ticking.

Really looking forward to this project series!

Good to see you are ready to go. Hopefully harvest goes well! We had a 200.. miss it! It was a good tractor!! Looking forward to seeing you make her all like new 👍 Thank you Pete!

Looks like you have a good project! Trying to prioritize winter projects here, and get things ready just in case I actually get to work on any of them🤔Thanks for the video Pete, hope you have a good one too

Pretty much a updated D17 which was an updated Wd45 and after all those years they were great tractors! Come to think of it moast had shift problems but you'll fix that, great winter project!

Looking forward to your harvest videos. Glad the 3300 is ready to go. I am full speed ahead on corn harvest here. About 2/3 done. I am looking forward to seeing you work on the 170 and to how you use it next spring. Should be a great tractor.

Thanks for the update Pete that engine sure sounds good. I believe you will have enough to do to keep you out of mischief this winter 😂

Nice 170 ac if you ever get the chance check out brayden bowman tractor salvage he is big in ac parts😊