Amazing Rig! 😮 BUT Watch This Before You Hit the Trails 👍 Full Unboxing and Test Drive FMS FJ40

Рет қаралды 4,272

Күн бұрын

The FMS Toyota FJ40 is one awesome rig, even despite a little work being required to reach its full potential. The officially licensed ABS body will without a doubt be a hit with hardcore scale RC enthusiasts. While this RTR model shows some great potential, many hobbyists will likely want to enhance this truck with some upgraded electronics, and some minor tweaks to the chassis. While I’m not sure this 1/10 scale platform is quite as polished as FMS’s famous FCX series models, this could soon change with future additions to FMS 1/10 scale lineup.
Introduction: 00:00 - 00:12
Unboxing and Overview: 00:13 - 05:33
Test Drive: 05:34 - 07:22
Post Test Drive Thoughts and Repairs: 07:23 - 11:47
Final Thoughts: 11:48
This truck can be ordered from FMS here: www.fmshobby.com/products/fms...
Subscribe for more videos and follow us on social media for more frequent updates and extra content.
_________________________________________________________________
Make It RC Store: shop.makeitrc.com
Make It RC Merch: shop.makeitrc.com/collections...
Website: www.makeitrc.com
Patreon: / makeitrc
Facebook: / make-it-rc
Twitter: / make_it_rc
Instagram: / makeitrc
_________________________________________________________________
#rc #toyota #rccrawler

Пікірлер: 24

@MakeItRC 4 ай бұрын

Thanks for watching everyone! This video is a little less “polished” than I would have liked. I need to figure out a better mic set up for when I'm talking at the beach. Regardless though I hope the information is useful. Having lost screws related to the steering on both the Mashigan and FJ, I felt it was an important piece of info to pass on. Check those fasteners everyone!

@TrokaRC 4 ай бұрын

Moving the pin on the esc from crawler to boat makes it freewheel/ no drag brake. However it makes reverse at 50% I believe. That being said a simple esc swap to 1080 is a must. Transfer case is dry along with transmission behind the 550. The weight required some injora inserts (red) is what I recommend. Finally if pushing this platform tightening the slipper a tad bit helped me tune it better to my liking. That takes us to the weak link, the dogbone from transmission to transfer tends to break under alot of load.

@TrokaRC 4 ай бұрын

Out of the box I immediately did a few upgrades: Fusion 1200kv, leaf springs & of course wheels + tires. Usually carry tools and screw set when out and about. Cool review.

@TheDirtRider101 4 ай бұрын

This thing looks fantastic!

@Fourwheeljive 2 ай бұрын

Great video! Thanx for the hints!

@ryand4786 4 ай бұрын

Great review , yes the transfer case needs grease too. I did all my driveline when switching to fusion pro, overkill for this rig but oh well. Also installed front inner fenders , huge improvement. Wheels , tires, RC4WD winch , Injora shocks and scale driver. Minor detail but the hood louvers are real , I thought it was cool they went to that level of detail

@Robert-ni6ut 4 ай бұрын

Nice truck it would be a good start for a full scale build 😊

@m.a.s2830 3 ай бұрын

Definitely would love to see a followup on upgrades. Good vid.

@MakeItRC 3 ай бұрын

Thank you! Currently working on a few mods on this rig. There's a lot going on but hopefully I'll be able to make a video at some point. 👍

@nicka.9073 3 ай бұрын

Nice review! I installed a Hobbywing 1080 for approximately $40 and found it made a world of difference when dialed in compared with the harsh drag brake found on the stock ESC. Good looking out with the servo horn issue, I need to check that! I also installed a set of Amazon sourced oil filled shocks, but I'm not sure I would do that again if I was starting over. I too enjoy the undamped appearance of the stock shocks, and given that this rig will be confined to the trail for me, the shocks I installed seem like a waste for how I will be driving this rig.

@MakeItRC 3 ай бұрын

Thank you! These are great rigs, they just need a little work to make them more enjoyable/reliable to drive. Working on a few simple mods for this truck currently. 👍

@thechickenacrossthestreet8563 4 ай бұрын

I sadly don’t have enough extra money to buy one 😢

@fordexp2002 3 ай бұрын

Exact same problem with my FMS Toyota Fj40

@MakeItRC 3 ай бұрын

Seems to be at least a somewhat common issue and a bit of an unfortunate oversight. Hope you were able to get yours sorted. 👍

@Travis5.56 4 ай бұрын

You made it out to Oakes!

@MakeItRC 4 ай бұрын

Yes great spot! Was wondering if someone would recognize it. I assume you're local?

@Travis5.56 4 ай бұрын

I’m about 30 minutes south. We usually hit it up once a month

@MakeItRC 4 ай бұрын

Nice. I'm planning to go out there more this year. Great spot, already met some great folks. Hopefully see you out there. 👍

@nurksmurf7167 4 ай бұрын

I must agree with your review. The body looks great but the car has some downsides. The ESC leaves no room for emulation. The servo isn't great, but it does its job on the trail. I lost the screw on the servohorn at the end of my first trail. I lost one of the blinkers on my 2e trail. One of the pins on my left front axle keeps backing out. The manual doesn't show the size of the screws - they all have the same partnumber. The transmission looks fragile - not sure how long it will keep up. The divorce-case looks more stout.

@alantaylor353 3 ай бұрын

Gtrat review.!! 👍 👍 👍 Thank you for taking the time to show us the extra little details. Stay safe out there mate & the very best wishes from Scotland 🏴󠁧󠁢󠁳󠁣󠁴󠁿 🙏 ❤️ 📻 🕹️ 🔋 🚗 🚖 🚕 🚔 🚚 🚙 🚘 🚓 🚒 🚑 🚐 🚎 🚤 🚁 🛩️ 👍 👍 👍

@MakeItRC 3 ай бұрын

Thank you! It's an awesome rig, just needs a few little upgrades and tweaks. 👍

@ToyotaGuy1971 4 ай бұрын

Yes, the inclusion of such features would increase the cost, but please stop calling me Shirley. I would say that's probably a 1/9 if those are 1/10 scales you were comparing them to. Not even close to 1/6 or 1/7.

@MakeItRC 4 ай бұрын

lol love the reference. 👍 I think mathematically the body is something like 1/6.5ish scale when you compare it to the real world body dimensions. Would have to double check though. The real thing isn't much larger than a CJ Jeep. The chassis however is about in line with a SCX10 III, GEN 8, etc. Just a tad larger so maybe 1/9 as you say.

@ToyotaGuy1971 4 ай бұрын

@@MakeItRC 😁Well, you may be right, but like you said, there's only one way to be sure, measure a real one and divide it by 9, 7, 6, etc. Whatever it is, it's nice.✌☺