It's pretty obvious these guys are not paid much, removing all the chatter marks with an angle grinder on something that size is going to take a very long time. (I would guess he has carpal tunnel within a few years ?) I wondered about the welding on top of screw but realised it was some form of very hard material when they started grinding on it so it's a smart way to get a 'soft' steel good wear characteristics and saves heat treating a 'better' steel part. The shop looks like it's pretty damp though with all the rust on everything, including the part being machined, probably took a few days? I hope the cameraman is giving a share of any money from You tube to the workers he's filming, they deserve it for putting up with him

The only thing that's amazing, is the lathe under this conditions still is running.

İş görüyor ise Sorun yok Kardeşlerim emeğinize sağlık Başarılar

Screw for plastic injection machine

I was wondering why he needed a lever to transverse then *I saw the angle grinding over the exposed ways

Chatter! A classic case for follow rest, lubrication. I guess these people know something!

Interesting but very hard work

Trabalho pesado, mas meu amigo esse serviço sem proteger o barramento, estraga o torno e é tão caro um torno mecânico

I feel like this video could have been sped up a little bit

It's alright fellas, 11/16 = .000010 in this part of town!!

There are materials that they are using to manufacture parts but Iam sure there are no set of eyes for them on the shelves or at the Phamarcy if they loose one. Safety comes first.

Спасибо. Увидел то , что мне надо. Дай Вам Бог здоровья.

The best, congratulations the somebody ! Tank's

that screw is used for plastic extrusion or injection, it must be fully polished and hardened by chemical heat treatment

They forgot to trough the finished product on the floor.

Fantastic and amazing job,thank for shared, and cingratulations

Merci beaucoup pour le partage de cette vidéo intéressant, très bon travaille et difficile, bravo bon courage et bonne chance 🙏🙏🙏👈 salutations à vous tous 💐🏆

Aside from the 19-century machinery this could be a medieval sweat shop. I could never understand the filth and squalor of the workplace. Center drilled 5/16? on a 2 tons shaft? On the positive side... the lathe way get ground at the same time.😂😂

Relação de com pressão?diâmetro interno cônico? Ou diâmetro interno escalonado ?

Esta muy grande ese paso para hacerlo en el torno la pregunta sería le adaptaron algún sistema para que el torno de ese paso por qué no creo que traiga de fábrica para dar esos pasos muy grandes

Esses paquistaneses já vivem um mundo Mad MAx. Quando o apocalipse chegar eles vão sobreviver e moldar o novo mundo

I have never seen anyone beat and chip notches into a grinding disk. That’s an explosion waiting to happen. Someone is going to get disemboweled doing that dumb shit

Самое кайфовое начинается с 23:00

Use lixadeira de cinta.

Amazing work bro

Великолепная технология производства! как с вами связаться для сотрудничества?

Killer boss. Nobody wears safety equipment.

Truly hard work👏

Всё хорошо, всё отлично. Но разве люнет подвижный трудно поставить. И защита направляющих станка от абразива. Всё чаще замечаю по всему миру переход на прямой привод шпинделя без коробки станка от эл мотора с частотником

Bhai ye aluminium se agar banaye to success hoga kya ... thermocol melt karne k liye..

Esa esmeril, tiene q ponerle un protección no puede estar lanzando chispas con metal al aire ,y respirando esos metales,

Look at that chatter when he’s roughing out the screw. You can see it from a mile away. I’m not so sure that could even be considered cutting by normal machining standards. Normal chips are very sharp c, 6, or 9 shapes yet they are basically using the brute force of the lathe and the hardness of the hss cutter to tear off metal. The tearing at 10:21 shows it real good. This stuff makes us machinists in the states cringe but I still find it interesting and watch it 🤷🏻‍♂️.

ماشاء الله

Pow a máquina de vcs tbm e muito boa

Lathing should start from a little low to a deep place

Molto bravo sto ragazzo bravo

Who needs a chip breaker when you have chatter.😂

Mantab...

Assalam alekum sir sir, I was asking that what kind of trading is involved in this waram that you are making, please tell us, please do a little method and tell us.

Horrible lathe work.

Very encouraging work done. It's a pity you have less than zero safety

Con un poco más de cariño y quizá alguien que les explique lo que está bien y lo que está mal co eso sacarán buen rendimiento a esos tornillos para plástico

A little oil on the bare metal at end of every day would save a lot of time with the grinder later

Lots of chatter. Waaay long for no steadyrest.

É impressionante ver como esta gente trabalha, sempre de chinelos, ambiente fabril terceiro mundo, mas produzindo peças incríveis. Honde estão as condições de igiene,e segurança no trabalho.

Молодцы

how to ruin your lathe ways in one easy step

That is good work...can I ask a question..is This spiral is divided into three section , feeding section, pressure section and metering section ؟

Poor, poor lathe ☹

Ok, the giant fabricated “tool post grinder setup” I get, but what was the stationary grinding wheel all haphazardly “clamped” to the tool post and with its “side” face (and a radius ground/wore into its face) just pressed against the periphery of the fast turning screw-what was the purpose of that after you just OD ground the screw prior to that?

কত গুনার পেচ?

24:24 Anybody knows what's he doing and what is called ?

👍I admire the work and skill here.💯

Wow

Mittelalter

Fix that bleeding lathe. The poor thing is screaming...

@19:30 anyone else hear the radio sound from the movie CONTACT

পিনিয়াম কত কত

Good lath work.

Your from

Объясните кто-нибудь зачем он диск на 22:50 надрубил в 4-х местах?

I always wonder how many steps the table takes to make the thread

Amazing technic? No kidding me.

Please reply

Конус сделан при помощи задней бабки ??????

Quality of the final product A+++

why even make this

Inka mob nambr chahye

Peça feia e mal feita ! Serviço porco !