Amiga 500 Internal Floppy Drive Cleaning and Maintenance

Рет қаралды 13,210

Error 42

Күн бұрын

Opening up the Amiga 500 internal Chinon floppy drive for cleaning/maintenance.

Пікірлер: 34

@SoulStarLA 6 ай бұрын

Thank you sir! Very nice to know how to properly take care of and save my Amiga floppy drives. Very much appreciated.

@Error42_ 6 ай бұрын

Thanks for the comment. Glad it was helpful to you 🙂

@deborahberi3249 2 жыл бұрын

One of the best Videos on cleaning/fixing A500 Floppy Drives! The Zoom in and clearly showing in more detail the various parts of the Drive was stellar...I've Subscribed! Thanks...-Mark.

@theamigashow9506 3 жыл бұрын

Thanks for making this video. I’m looking to see if I can bring 2 old drives back to life, so this will help!

@005AGIMA 2 жыл бұрын

Fantastically detailed video. Love it. I need to do this to the FDD in my A1200. Been putting it off for waaaay too long.

@Error42_ 2 жыл бұрын

Thanks, I hope it helps :-)

@retroreuse 4 ай бұрын

Mate this is a great video. Hello from New Zealand.

@lurkerrekrul 2 жыл бұрын

14:50 - That switch for detecting a disk was what usually gave me trouble. After a few months to a year of use, the drive would suddenly start acting as if I'd ejected the disk, even though it was still in the drive. Spraying contact cleaner into it had about a 50% chance of working. One day I got the bright idea to take that unit apart so I could really clean the contacts . Big mistake! It took me close to an hour to put it back together! The base of each pin is a fatter round section with a notch in it. In this notch is a U-shaped brass contact that's about 1/4 the size of a grain of rice. When the pin is pushed down, this microscopic contact connects two contacts in the base and completes a circuit. The fact that it's so frigging tiny is why it causes so many problems. The area that makes contact is so small that even a speck of dust can cause problems. And once you've taken it apart, getting both contacts to stay in the little notches while you put them back in place and snap the top on is epically frustrating. At one point, I seriously considered just chucking the parts in the trash and wiring a couple toggle switches to the board just so that I wouldn't have to deal with it ever again.

@SalvatoreBognanni 4 жыл бұрын

Thanks for this very thorough walkthrough mate!

@Error42_ 4 жыл бұрын

Thanks :-) If you want thorough, check out GadgetUK164's channel if you haven't found him already.

@raggersragnarsson6255 Жыл бұрын

Fingers crossed that this works for me. Great video, rhank you very much.

@bobbymalta73 3 жыл бұрын

Thank You for Sharing Dear Friend i will follow you suggestions! Bless You.

@blackterminal 6 ай бұрын

I just did some work on a A500 floppy dtive today. The eject wasnt working. Compared to an Atari ST I found the drive hard to work on. The hardest part was actually screwing the drive back in. The three base screws did not want to line up.

@bicio751 3 жыл бұрын

great review ... thanks ... what do you use to clean the head? just cotton or a specific liquid for magnetic heads? thank you

@CeccioFC 3 ай бұрын

Nice video!

@froggie6311 3 жыл бұрын

thanks Error 42, damn fine video!!

@larssommer5756 3 жыл бұрын

Thank you for sharing.

@pcretropcworkshop8031 11 ай бұрын

good job~

@Electrotat 7 ай бұрын

Thank you

@8bitwidgets 2 жыл бұрын

is this drive the same as the A2000? I have two bad A2000 drives.. one tries to work but fails while the other seems less responsive overall when accessed.. were the drives of this era interchangeable or unique to each model?

@JoZf_Gibson 3 жыл бұрын

Merci

@Snowwie88 2 жыл бұрын

What kind of cleaning 'alcohol' based stuff do you use to actually clean the head? I could not really figure out what you were saying, what stuff you were using on that cotton swab. And the grease you use, is that of any particular type?

@TheRomsoft 2 жыл бұрын

I think he used isopropanol alcohol, very commonly used when working with electronics. And he used something called "Graphite bearing grease" for the shaft.

@brufnus 2 жыл бұрын

The head stepping is because it needs to read a track in order to distinguish between the same disk ejected and re-inserted, and a different disk inserted. I don't think it would've been necessary for it to do it with no disk inserted, of course, but apparently that's how they designed it back then. Anyway, that should be the reason for the head ticking. c",)

@laposerafini1262 Жыл бұрын

Great video!! Thank's!!

@Cinnerman87 4 жыл бұрын

Where's the heat shield

@lassie6 3 жыл бұрын

12:18 arm?

@TheRomsoft 2 жыл бұрын

"Arm" is a good word here :-)

@sunstormer5064 Жыл бұрын

I believe it's called a "suspension arm" as it suspends the header over the disk

@RobertBullock 4 жыл бұрын

OMG please stop lifting these heads up and spend the money on a cleaning floppy. Bad for springs.

@Error42_ 4 жыл бұрын

I used to have one of those cleaning floppy disks, I always thought it would rip the heads off with the noise it made! I don't think much to them though, they can only at best clean the surface and not always well enough, there's often a lot of crap that collects around the head. You do have to be careful like you say, but no springs were harmed in the cleaning of this drive :-) There's a piece of flat spring steel as well as the actual spring and it's that bit that is the most delicate if it gets bent too far, but you can feel the limits of that if you are careful.

@RobertBullock 4 жыл бұрын

@@Error42_ I use compressed air and a Qtip AROUND the drive head area if it's needed and most of the noise is generated by the jacket of the floppy against the material so that doesn't matter. The MAc 800k drives are more delicate, IMHO, so this may be ok for some models but again IMHO not for others. I have seen varying amounts of spring robustness too, so I wonder if the strong springs wear the floppy faster. :)

@EllipseGamer 4 жыл бұрын

Great to see 👍 I'm having a few issues with a drive so it's great to see the components for a beginner like myself