Good tutorials serves as a revision tutorial also for everyone thanks a lot for uploading these kinds of tutorials during pandemic lockdown

very good tutorial I really needed someone to explain these stuff as I am like an old lady working on computers

It is very good that you comment your actions during the video!

Showing comment, your way of explaining was superb...and also back ground music was calming 😅

Amazing content and very clear explanation of each step.It was really usefull.Thank you,keep posting more such basic fluent tutorials.

Great... Thank you sir... This is my final year project

your tutorials really helped practicing models,Thankyou.

very very good tutorial ever seen Thanks a lot

Thank you so much for such a wonderful video. Waiting for few more like these.

The class is saying it very well - understood way. Good tutorial. Thanks a lot.

Wonderful Session! Thanks a lot :)

Excellent in-depth beginner level video representation....❤️

Very informative video..thank you

Thank you for a great beginners tutorial 👍

Nice video! How can wall shear stress be generated in turbulent flow?

Here you have mentioned there will be another tutorial on adjusting the number of CPU processors to be used while solving. Did you already make that? Great work, by the way.

Thank you for such a wonderful explanation

Superb work Sir, Can you plz upload a video on turbulent flow through pipe and externally effect of radiation. (Receiver of Parabolic collector)

amazing can you please make a simple tutorial for two phase flow simulation in vertical pipe ansys fluent?

great work man..keep it up specially explanation is good..

Thank you. Can u share a simple video tutorial on airborne dust simulation in underground tunnel ?

Good tutorials thank you ..please do insteady flow through .

Love your work💪💪💪💪 keep it going

how do we set the type of mesh ? either coarse or medium or fine

perfect!I was wondering if i can choose an axis that away from the boundry instead of the boundary itself

Thank you. Very useful!

Great video, It would be helpful a video about the DDPM Model

Nice tutorial , I am really enjoying it . But please can you make a video on the flow that causes scour around a pile structure, and also a flow that of a tidal turbine . Thank you

thanks a lot bro

Thank you very much for such demonstrated tutorials. It helps us to understand from geometry creation to post-processing. Could you please make a tutorial on multiphase flow simulation consisting of 3 phases?

great work man, A question could you please explain what is residual value how to decide which value is best how the equations achieve this value thanks..

Can you make a video for laminar flow between parallel plates when a porous medium is present? Your videos are very helpful. :)

Good one.. I have practiced..

Thanks a lot for the tutorial

Thank you sir 🙏🙏🙏

Thank you for your video it is great. It would be perfect if you could do a tutorial about shear thinning fluid flow inside pipeline

Nice but only one problem in the beginning properties tab don't appear on RHS. We need to click on LHS icon down arrow and then on properties to start the video.

Great work. Can you do the diesel spray simulation please?

after the solution is converged x-coord y-coord this type of writtings are not coming.

Big thanks .

Hi. Do you have or recommend any resource material on defining the price for a simulation/modeling consulting service? I am lost. Should I price it hourly ? Thanks.

Nice Tutorial but in the end i can only see my boundary surface .Like a hollow cylinder,What can i do to change that

Why did you directly made 2d of circular pipe? like can we proceed by circular section?

This is so useful . Would you please make or guide me to simulate heat transfer charcteristics through circular microchannel??

As the initial simulation provides results for only half the pipe? Do the results then need to be doubled or is this the results for full pipe but only shows half in the image?

The performance of the hybrid nanofluid application in a single jet impingement cooling

In the problem statement you have pipe, why you use rectangle shape?

Actual model of the problem is 20mm dia pipe with 100mm length, but you create 10 X 100 mm flat surface. What is the reason for it?

I'm unable to select 1 sketch for making surface..eveyrtime it shows 0 parts,0 bodies

I am doing a 2D rectangular flat plate ( zero thickness) for blood flow through an artery. the only boundary conditions available is the inlet velocity at 0.23 ( Uavg) and the outlet pressure at 0. in terms of the boundary condition section can you guide on the selection I should make on outlet condition. the Umax is supposed to take an expression Umax = 2 x Uavg.

Can you please share a proper simulation guide video for pulse detonation engine with fuel as c2h2 and oxidizer as air? Also, how to saparate deflagration combustion zone and detonation zone in this simulation of pulse detonation engine. I will be very thankful for your support.

In which video do you guys talk about importance of meshing?

Thank you

Hello，could you make a video about battery cooling plate simulation? Thank you.

Is it possible to extract the G value of the graduated velocity from the Ansys program?

I followed all the steps accordingly, but unfortunately, it shows an error while starting the setup like No error handler available Error: Cortex received a fatal signal (SEGMENTATION VIOLATION). Error Object: (). any solution

Do you have any material about Gauge pressure? If i must use 0 or another value.

I think you are using ansys v16, but showing 2020 r1. Bcuz I have that one...Nd it's interface is totally different.

I am looking towards simulation of circular microchannel and i created the geometry and mesh in micrometeres. Now in Fluent solver, micrometers units is not there and now will i have to put scaling factors and then scale or if mesh and geometry are already in microcmeters,Fluent directly keeps the domain extents in 10^-6. So what should i do? If already in domain extents by keeping the units metre, its already in value of 10^-6, do i need to scale again or leave and continue? It is also showing solution is converged? Is it sue to the small dimension? Please give me idea.

you have put in set-up operating pressure:101325 Pa, gouge pressure inlet and outlet=0 and initial velocity:0,0005 m/s. why the velocity grow up? i do not have any difference pressure in the boundary conditions...

Please make a video regarding turbulence validation of NACA0018

please help me out! I'm getting floating point exception error no matter how many times i try...please let me know how to overcome that error...and where I'm going wrong!

The pipe outlet velocity is higher tha inlet velocity?

I'm not getting option of adaptive meshing in ansys 16

Sir do some icem cfd meshing tutorial , or any personal class is also ok to me , because here nobody knows about it ,I want to do a project on that pls help me sir.

What's the different between laminair et turbulent

Hi there, can anyone help me with calculating the Reynolds number from this process for my dissertation

anyone knows how to solve floating point exception after running calculate?

Here the exit velocity is increasing?

do you have a tutorial for hybrid channel flow?

I need to model a water tank tower and the base of tower has earthquake as harmonic displacement (for eg. 200mm*sin(omega*t)) can I model in fluent? I am trying to model in fluent but water has not any inlet and outlet. Can you help me in modeling?

press ok 流體力學靠你了

what did u do at 2:48

can we have vortex flow

How would you know the Reynolds number is 9.95 ?

How to save this project in ansys 2020R2

Sir, I'm using ansys 16.0 version. Using face meshing option I'm able to change the element size but unable to find adaptive meshing option. Also there is no such option in defaults. Is there any way i can proceed?

I'm getting problem when open setup like views are black screen I don't know what to do can you help me? ( In viewer area)

How would I do a non dimensionless plot

what does id mean?

Hi. Why did you select diameter 10 instead of 20

please iam need pdf (flow in pipe)

It will be , more good if you if you arrange videos orderly

我想要中文翻譯

Can we change radiation shape factor in ansys? (F)

MODELING SPILLWAYS

Bro the piano is so annoying

t cần con chó chạy qua

floatig point error

Good tutorials thank you ..please do insteady flow through .

In the problem statement you have pipe, why you use rectangle shape?