Antique Stone Gas Lamp Restoration with AMAZING outcome

Рет қаралды 106,292

3 жыл бұрын

Antique Stone Gas Lamp Restoration with AMAZING outcome
Welcome to World Restoration
My mission is to restore all the old things, rust, antiques and lots of things worth doing:-)
And of course I really love to do that:))
I will share a new restoration 2 times per month, So please subscribe to my channel to make sure you don't miss anything.
Thanks for all your support and watching, I really appreciate it
Best regards, ^-^

Пікірлер: 112

@WorldRestoration 3 жыл бұрын

Antique Teapot Restoration with AMAZING outcome kzfaq.info/get/bejne/o8mZpseDm8DYipc.html

@DrFelonious 3 жыл бұрын

Amazing? I'm amazed it survived the angle grinder and claw hammer!

@reginaldwilkinson6019 3 жыл бұрын

I don’t understand why you do electrolysis when you grind the parts anyway.

@nekif820 3 жыл бұрын

It seemed like he didn't even give enough time for the whole electrolysis process to finish. It was like he was just impatient and decided to finish it up with the grinding wheel.

@michaelhrosar7814 3 жыл бұрын

I didn't see anything AMAZING about this. He really didn't do anything. He didn't even clean it well. The I bolt was still rusty and the body was all scratched up.

@daveshipman2677 2 жыл бұрын

my thoughts exactly mike..?

@ALCE52 Жыл бұрын

we all start out rookies.and progress with each project.be well my friends.

@pillowpants1983 2 жыл бұрын

Invest in a sand blaster, complete the project, make it look amazing if you're going to claim an amazing outcome. Rushed, shoddy work doesn't pay off.

@chandlerdavis952 3 жыл бұрын

Instead of using the plumbers wrench stick a screwdriver through the eyelet will give. Much more leverage and not leave the teeth impressions

@user-xk3om5sy1h 2 жыл бұрын

goood job i love it..but please change your table😵😵 it need a restoration

@matthewmoran1249 3 жыл бұрын

I wouldn't be putting my fingers that close to a spinning grinder disc. He's either very brave or has a screw loose. Amazing ? Yeah, he's still got his digits !

@CraftGentRestoration Жыл бұрын

It is soo nice..super 👍👍👍❤❤❤

@Oussama-w2a0c03 2 жыл бұрын

Super !!!

@chrismillar6404 2 жыл бұрын

I love watching your videos they are better than TV. :-)

@kiyote437 3 жыл бұрын

You are certainly an outside-the-box thinker, but not necessarily in a good way. Sometimes things are done a certain way for a reason. For instance, the claw end of a claw hammer is not typically used to strike things, especially delicate things, due to the risk of seriously damaging the workpiece. Perhaps you should consider using a wire brush to remove scale next time.

@nielsantsorensen881 3 жыл бұрын

Belissima!!! Parabens.

@persioboni9373 3 жыл бұрын

Muito bom.

@mikemcclure1855 3 жыл бұрын

Great job, considering where you started from. I have one question. Why not paint the steel parts. Not a criticism, just a question.

@nyg_dbone 3 жыл бұрын

You didn’t even restore it 🤔

@homeyshlitz 3 жыл бұрын

What was the powder and liquid you put in at the end? I'm trying to figure out why its called a stone gas lamp. I figured 'Stone' was the name of a brand.

@terencenaylor5441 3 жыл бұрын

I believe it to be Calcium Carbide powder, and the liquid to be Water. When mixed, Acetylene gas is produced, which is highly flammable.

@nyg_dbone 3 жыл бұрын

Took it apart cleaned it up and put it back together that’s a restoration 😂

@MegaJohnson12 2 жыл бұрын

Try using the right size screwdriver for a change and see how that works for you.

@diyresttube 3 жыл бұрын

done wathching always satisfied at your work.

@pafalcao5345 3 жыл бұрын

How did you do it inside?

@Slenderman182 3 жыл бұрын

so that's why so many houses burned down back in the day

@GriswoldCain Жыл бұрын

I kind of like the fuckups and multiple non-working tool selections to accomplish a task. Normally those are cut out.

@suhayl5157 3 жыл бұрын

Seriously? Is this your amazing outcome? should have left this nice piece to someone who knows what to do.

@mangalaismeji 3 жыл бұрын

Agree with you

@nekif820 3 жыл бұрын

Agree. It was very sloppy and just plain cringey. I mean, gosh, he massacred those parts with the grinding wheel. Even after assembling them back it still looked messed up.

@Pizzpott 3 жыл бұрын

I agree. Good grief. The scratches on the brass were deplorable, and there were still marks on it too. This wasn't finished at all. Won't watch any more from this creator I'm afraid.

@n0named 3 жыл бұрын

@@Pizzpott You've misspelled. It should say "creature" :-)

@GT_Racer347 3 жыл бұрын

Sweet 👍🏻 👍🏻

@WCW61 3 жыл бұрын

Parody?

@zzota 3 жыл бұрын

Painful to watch. Do you not have a wire brush? I think the white powder must be Calcium Carbonate. It reacts with water to produce acetylene gas, which is flammable and burns with a very smoky flame. Usually the bottom chamber holds the powder and water drips down from the top chamber.

@garymucher9590 3 жыл бұрын

I enjoy restoring things as well. But I think I would have passed on this one. So much wrong with it and other then some bright shiny metal, it still looks pretty beat up... Thumbs Up for your efforts though.

@WorldRestoration 3 жыл бұрын

Thank you. We will change

@oneshotme 3 жыл бұрын

Enjoyed your video and I gave it a Thumbs Up

@WorldRestoration 3 жыл бұрын

Thank you

@oneshotme 3 жыл бұрын

@@WorldRestoration You're welcome!!

@mangalaismeji 3 жыл бұрын

You called this amazing? 🤔

@leisongivangomo5656 3 жыл бұрын

Very nice!

@RESTORATIONOFSCRAPMETAL 3 жыл бұрын

very nice restoration👍

@feisdee1 3 жыл бұрын

No new gasket?

@mullerman1104 3 жыл бұрын

Here is a tip. The Lamp gets to much gas. The gas outlet needs to be smaller, so that it doesn’t produce as much smoke and shines with more continuity. But otherwise a great restoration.

@russbilzing5348 3 жыл бұрын

He might also have tilted the spout upward as it should be.

@user-hx9xy3jp4f 3 жыл бұрын

Это не рестоврация, грубо а также очень поверхностно. Там ещё много работы. Автор не своим делом занимается.

@romashmakov6709 Жыл бұрын

Страшно было смотреть как он разбирал

@shafismaili1347 3 жыл бұрын

I haven't seen the vid. Assume by amazing outcome the old can must have become a flamethrower.

@scottzissman2575 2 жыл бұрын

Every single thing this guy does has the same burnished finish to it. Someone make him stop.

@bonzie321 2 жыл бұрын

95% of the comments - bad boys job. I got to admit it ain’t good fella. Pretty crude work.

@aridesouza11 3 жыл бұрын

Pouco estressado esse restaurador 🤣🤣🤣🤣

@RicardoCamillo 3 жыл бұрын

Isto não é uma restauração apenas um conserto.

@CarsRestored 3 жыл бұрын

Me: No way he can restore this World Restoration: Hold my 🔧

@IronHide1686 2 жыл бұрын

this was not a restoration; you just clean it, not even fix the holes on the loose screws, i think this could have been a better restoration! 👍

@user-rv9vw5ef9e 3 жыл бұрын

Acetylene was named in honor of aztecs by french conquestador.

@nijolevidzeniene3436 3 жыл бұрын

Происходит от франц. acétylène, далее из лат. acetum «укус» + франц. éthylène «этилен» Русский Викисловарь

@user-rv9vw5ef9e 3 жыл бұрын

@@nijolevidzeniene3436 у меня плохо получается в юмор.

@nijolevidzeniene3436 3 жыл бұрын

@@user-rv9vw5ef9e бывает

@5cloudwalker 2 жыл бұрын

Awesome!!!! Now if you wanted to return it back to the mess it was it will take a lifetime of abuse and neglect 🧐 that achieve the takes a lot longer lol

@alex02101967 3 жыл бұрын

Not a perfect restoration,sorry

@joseluiscossbu8036 3 жыл бұрын

si vas hacer una cosa hasla bien si no no la hagas

@horvathattila377 3 жыл бұрын

What is this Dart Wader sound???

@UNSERALVUJUDE 3 жыл бұрын

Bringing that old rusty thing to life was amazing ! Thumbs up ! I wonder what is the white powder and the liquid used to fueled and light up!

@johnnytoobad4287 3 жыл бұрын

It is calcium carbide. When mixed with water it produces acetylene gas.

@laurahelenaxou1834 3 жыл бұрын

Still a lot of work to do to call it an "amazing outcome"... 3rd video I watch on this channel and 3rd deception, time to move on... 🤔

@maddadd1 3 жыл бұрын

You have got to be kidding.

@saureano 2 жыл бұрын

*I've seen restoration badly done, but yours, if it surpassed itself, a real rubbish job, aren't you ashamed to present this mediocrity????*

@amilcarmoncada1801 3 жыл бұрын

Estupenda restauración de lámpara de gas de piedra lumbre antigua, resultado increible respetos y saludos desde Venezuela.💯👍💯🤘

@maunguyen852 2 жыл бұрын

Cai đen khi đâ

@angryasianjim 2 жыл бұрын

Came here to see if anyone else was cringing when they saw the angle grinder come out. Why? Electrolysis would have worked fine. You didn’t even buff the scratches, yes scratches NOT swirl marks, at the end. At least use some fine sand paper to get the big ones out… yikes. Could’ve even left it with a brushed finish and it would’ve looked better. Honestly, this was kind of painful to watch.

@abdourahmanesambanor9306 2 жыл бұрын

demonter plus soigneusement

@outdoorinterests 3 жыл бұрын

Its a carbide lamp but not an original.

@skoalonguys6788 3 жыл бұрын

That took a lot of time and effort its nice to see you do cares enough to want to restore old stone gas lamp and make them look brand new again. Great job 🍻🤟👍

@chandlerdavis952 3 жыл бұрын

Okay can't watch this. Hitting with the claw end. Of the hammer is too much cya

@maunguyen852 3 жыл бұрын

Bo di cai den khi da bay gio ai ma xai

@timrenier3399 3 жыл бұрын

Watching him doing these Restorations is very cool & very relaxing!

@fernandoalfonso9984 3 жыл бұрын

Guy really you are the best one !!! The pie topping is when you lit it

@megenberg8 3 жыл бұрын

the Gordon Ramsey of restoration.

@charleenheath6116 2 жыл бұрын

What they said. leenotcharleen

@walkertongdee 3 жыл бұрын

WTH dows stones have to do with it?

@webtoedman 2 жыл бұрын

If restoration was a sexual activity, you would be in prison.

@juancarlospereyra7855 3 жыл бұрын

En cualquier momento te llaman de un museo para que vayas con la amoladora y les restaures todas esas cosas arruinadas que tienen...

@igorfeldens605 3 жыл бұрын

Y asi se pierde la historia...

@danipopescu2205 3 жыл бұрын

Amazing!!

@andreasm481 3 жыл бұрын

Much more could have been made of the lamp. The result is not convincing. That's how you earn money on YT ? Auf gut Deutsch würde ich sagen : Anfänger ! Setzen ! Sechs !

@jeanpeeters5450 3 жыл бұрын

wtf molesting al the parts with a grinding wheel worst restoration ever tbh

@nekif820 3 жыл бұрын

I agree. I was starting to feel uncomfortable when he just grinded everything clean. It still looked messed up when he assembled the parts back. Overall I think it was a very sloppy restoration. Not high quality at all.

@jasonrogers1576 2 жыл бұрын

Your did a half-assed job on that and you call that an AMAZING outcome..? Not impressed.

@HelloNotMe9999 3 жыл бұрын

Those poor tweezers. Get a proper scraper or set of dental picks!

@ia220 Жыл бұрын

Destriyer of a lamp not a restorer...

@CoastalCrafterUK 3 жыл бұрын

I'm sorry but this was awful.

@notwocdivad 2 жыл бұрын

NO, NO,NO, Don't hit things with the claw of a claw hammer it is there as a lever to pull out nails! The 3 bits of the handle looked as though they should have been straight and an angle grinder on brass or other soft metal? I think not. Sorry but I must speak as i find!!

@WorldRestoration 2 жыл бұрын

Thanks for the feedback, we will try harder in the next projects