2004 Nissan Titan Valve Cover Gaskets & Camshaft Sensor

No video

2004 Nissan Titan Valve Cover Gaskets & Camshaft Sensor

Рет қаралды 31,762

APDTY

Күн бұрын

Пікірлер: 31

@dm-qx9fy 3 жыл бұрын

These are very high quality and thorough videos. Thank you!

@nojusb4377 6 ай бұрын

By the way the service manual calls for rtv on the fronts of the gaskets and the torque specs are 2.0nm the first pass around and 8.3nm the second pass in the correct sequence. Other than that great video 👍

@oyoquimezahernandez2603 4 ай бұрын

Thanks buddy I have one Nissan armada 2006 this video is important for me thank you good work

@burtblyleven3011 3 жыл бұрын

Love all the Titan vids, not enough info out there for these under appreciated trucks. Maybe future Evap canister replacements/service. Maybe rear axl seals. Rack pin replace?

@build.drive.fish. 3 жыл бұрын

Awesome tutorial. Mine just what I was in store for. Not too bad at all. Hardest part looks like when your putting cover back on with gasket falling out lol.

@flippinized 3 жыл бұрын

Do you have torque specs for the 10mm perimeter bolts?

@abuahmedabdurrahmanalamree6122 11 ай бұрын

Good work bud very good work by just a question you didn’t think about undoing the negative on the battery because you were unhooking all types of sensors

@antoniomunguia4065 7 ай бұрын

Excelente 👍👌👏🏻👏🏻👏🏻👏🏻 gracias amigo👍, bendiciones 🙏🏻, good job 👏🏻 thanks a lot 👍, God bless you 🙏🏻.

@TheGuruStud 3 жыл бұрын

Fake news, they're serviceable with a hole saw or just use RTV 😁. Gasket has to be RTV'd in. You'll never get it to stay with the tight fit, then it rolls in the back and you're doing it all over again. This is especially true on rwd V6s. Also, no RTV on the front corners means it's going to leak. Cmon, that's Nissan 101 (along with the green connectors being stupid).

@db4652 3 жыл бұрын

Gracias . Have infiniti qx56 04 the same problem 👍🏻

@toddwashington8163 3 жыл бұрын

How did u remove the bolts on the back of the valve cover? They are so hard to get to

@billj818 6 ай бұрын

2005 Nissan valve cover

@robinbanks5734 3 жыл бұрын

Question : serpentine broke on 2004 Nissan titan. now, it turns over but wont start. ( did not replace the belt because, i thought it should run without it) also found out it had no oil on the dipstick. Could the belt have taken out a sensor, and or is there a oil sensor that would stop the engine from starting.

@aaronkowalewski659 2 жыл бұрын

Did you use rtv silicone on the front? I've seen some videos where they apply silicone to either side of the hump on the front of the valve cover gasket is that necessary?

@emailjlira Жыл бұрын

You didn't provide torque specs and the valve or rocker cover has a tighten sequence to tighten down the bolts in the correct order. Make sure to look that up.

@betocastaneda1597 3 жыл бұрын

hello, do you have any sequence the screws to tighten or some measure to tighten

@drizzedre 3 жыл бұрын

Hey I have a 05 armada se off road and it cranks but wont start I replaced the ipdm and the crankshaft sensor still nothing just the same crank no start could it be the camshaft sensor that could the cause of the no start

@josephkoslov3251 3 жыл бұрын

Sounds like an issue I had on my 05 Titan. It turned out to be the camshaft position sensor.

@drizzedre 3 жыл бұрын

@@josephkoslov3251 I have that sensor I will install tomorrow morning I will keep you updated if run into problems can I reach out for help thanks buddy

@johnnydo6410 3 жыл бұрын

@@josephkoslov3251 Hi Joseph, I have 05 titan. engine turn but didn't start up the engine? Do you think i have a problem with camshaft sensor?

@Major992 3 жыл бұрын

@@josephkoslov3251 did your titan ever cut off while driving? Having issues with mine doing it. I did the ipdm test and it seems fine. Truck starts fine but cuts off here and there while driving

@catbertz 3 жыл бұрын

@@Major992 I'm having that exact problem right now with an 05 titan. It happens after she's run hot, like freeway speeds. Relaxed driving doesn't seem to cause it so far. I'm troubleshooting various items. Cleaned throttle body and Mass air flow sensor, ran ipdm test. Next is camshaft position sensor, since it keeps throwing that code on my reader. I assumed that was a side effect, but I'll swap the sensor now to see.