I was the subscriber that asked for help. I cant THANK YOU enough. I spent hours searching the Neptune forum and Reefing forums only to come up with blanks. With your expertise and help I had it working within minutes. Appreciate it Tha Bizness.

Excellent video, already answered one question that I have. Thanks a lot.

Great video and explanation. I wish the apex manual were half as good.

Excellent video man! Thx for sharing!

Great video! Very helpful!

Nice explanation

Hope you're well. So I have 3 electric valves/solenoids connected to my RODI system and powered by my apex power bar. Currently, I have them working twice a week on a schedule to automatically fill up my RODI reservoir. However, I would like to now also create a manual button (either through feed mode or through a virtual outlet) to generate some fresh RODI water on demand. I tried a few commands, but it doesnt seem to be working. Currently, to fill up my RODI bucket, it takes about 60 minutes. Valve1 opens the main water line. Valve 2 opens the RO flushing/waste water. Valve3 directs the water into the DI. So basically what my current programming is: open valve1 for 60 minutes while simultaneously opening valve2 for 2 minutes to flush. After 2 minutes, valve2 shuts down while simultaneously valve3 opens up. After 60 minutes, valve1 and valve3 both shutdown, while simultaneously valve2 reopens for only 1 minute to release excess water and pressure. Your help would be much appreciated! thanks

I did basically the same thing with my vortec pumps but I did it different. Basically I have Feed A control my return pump and skimmer. I put a defer on for skimmer so it comes on several minutes after my return. Then I control one of my vortecs(MP-10wQD) via my return pump (If Outlet Retpumps OFF Then Off) I added a one minute off defer, Then I control my other vortec(MP-10QD) via the first one (If Outlet MP-10wQD OFF Then OFF) Then I put a defer off and defer on, on my MP-10QD so it runs for 2 minutes into feeding before it shuts off and then stays off for one minute longer then the MP-10wQD, that way they are not synced up with each other for a more random flow. So what I get is when I hit feed A return and skimmer go off, one minute later one vortec goes off then one more minute later the other goes off, then after 6 minute feed return and one vortec comes on and one minute later the other vortec comes on and like 3 minutes later still the skimmer comes on.

Tha Biz dropping that knowledge.

Very Very Cool, Biz... :)

Nice tank you git there, also nice set up with the apex, hopefully you have a video on that cause am trying to steal ideas to do mine Neptune set up cause now is all a bunch of cables Nextel the module and main control

BIZ can you help? I am sure this is simple for you but I am having a hard time. I want to set up a feed mode where I can ramp down my COR20 to 5% so that when feed mode is done I don’t have to deal with all the air bubbles from fresh start up from shut down.

Hello I know you did the video a while ago but in it you say about a email alter if a plug is left on to long do you have the code for this or how about another great informative video.

Biz - I have two MP10s with a backup ecotech battery in line. Can I do the same thing substituting the MP10s for gyre? I also want the auto feeder to roll once 3 minutes after the feed mode has started. Thanks In Advance

I have apex wave makers and am also trying to get my cor 15 to shut off and one of the apex wave makers to run at 10% capacity. Can you help ?

Hello there, I my self is having a hard time with my feed programing as well, I'm trying to turn on my mp10 after 3 min of feed cycle, I been struggling with getting it correct, and when I get it close my mp10 stays at 100% and it needs to be at 50% during feed cycle a i have the wxm module for both my xr15 pro gen 4 and my mp10 , I know you can figure this out, all help would be deeply appreciated thanks, I'll be watching your channel

Hey, im trying to set my dashboard similar to yours with graphs on more of the parameters. You seem to to know how to do this from the look of your dash. Any help would be very much appreciated.

Cool ! Enjoyed the video.. could be a new series from u...

Very cool.👍 Do you know how I can get my camera to show up in my apex dashboard?

Hi Biz I am concerned that if my return pump fails I want 2 things to happen 1 I am notified by alert 2 my pump feeding my reactors turns off also to save flooding or running dry How can I achieve this please? Many thanks M