Aquarium model 8 - Make Aquarium Chiller cool for 100 liter fish tank

No video

Aquarium model 8 - Make Aquarium Chiller cool for 100 liter fish tank - [Piece of Paper]

Рет қаралды 414,051

Күн бұрын

How to make an Cubic 30 aquarium tank
• Aquarium model 6 - How...
How to make a led light aquarium
• Aquarium model 5 - How...
How to make Co2 for aquarium
• Aquarium model 4 - How...
How to make Filter outside the aquarium
• Aquarium model 3 - How...
How to make an aquarium tank
• Aquarium model 2 - How...
Make an aquarium with black glue
• Aquarium model 1 - How...
Make a water chiller for the aquarium at a cheap and simple cost
• Aquarium model 9 - Che...
3 Peltier - TEC12706 - 60w, with water radiator
Note that it is not a substitute for genuine water chiller (Chiller). Because manufacturers have created perfect products
This clip is just for entertainment and for hobbyists to craft craft items
Have a nice day
If you like my Clip, give me 1 Like and 1 Subscribe
If my Clip is not good, please help me by leaving a comment below
I will try to do better
Thanks You Very Much
In the next clips I will share different Aquarium models and Filtering system and how to do i. See more clips on aquariums below the description
12v DC-1020 Pump
3W
Hmax - 0.4-1.5m
Qmax 200L / h
XH-W1209 Temperature Sensor and Controller
P0: Hot or cool
P1: Temperature range of operation
P2: The maximum value is adjustable
P3: The smallest value is adjustable
P4: Adjust the error of temperature
P5: P6: ...
You can use larger capacity Chip-Peltier (12710, 12715, 12730 ...)
This cooler can cool small aquariums of less than 80 liters of water
Have a nice day
-- don't drink and drive --

Пікірлер: 430

@rayb.1376 4 жыл бұрын

I'm researching using peltier devices for cooling a water reservoir of about 16 gallons. I doubt I'll use water as a heat sink but, who knows? It's still a great idea. Just wanted you to know that I appreciated the video and the parts list. You've given me inspiration and you've motivated me to try something similar.

@BC-uu6iz 4 жыл бұрын

tks my hat is off to you Sir great work was working on a similar project with four modules! now I've seen you showing the project made me feel great with similar idea tks again

@pieceofpaper924 4 жыл бұрын

Thank you very much Have a nice day My Friend

@amirhosseinb4920 2 жыл бұрын

It was great DIY I saw . its work perfectly and I will use that in my planted tank . thank you for your best learning

@MrPraveenGeorge 5 жыл бұрын

This method using direct water flow is more efficient and works faster. Good idea

@pieceofpaper924 5 жыл бұрын

Thank you very much Have a nice day My Friend

@kalaiselvan3956 4 жыл бұрын

@@pieceofpaper924 it's a piece of shit ...Peltier never works .!!

@willianmatias4782 4 жыл бұрын

Piece of Paper como chama esse aparelho, qual a capacidade dele pq queria fazer um nano reef isso seria bom

@uzlaamaliyah5511 4 жыл бұрын

@@kalaiselvan3956 u need more study

@micio_solo 4 жыл бұрын

@@kalaiselvan3956 at least he tried and built it smarten us up.... your contribution to his effort should have been a plain "thanks for the idea buddy" and not a comment about excrement...

@Dead_inside.... 5 жыл бұрын

Идея хороша, но для аквариума нужно переделывать. Ведь аквариумная вода содержит бактерии и дейтрит. Со временем водоблок забьется и обростет бактериями. Упадёт эффективность. Холодный контур должен быть изолирован от аквариума. Рекомендую использовать бронзовую трубку как радиатор в аквариуме.

@pieceofpaper924 5 жыл бұрын

Yes Thank you very much for sharing your thoughts with me and everyone In this clip I just want to test the performance of this product for everyone to know To use the fact we will have to do better Thank you very much Wish you a happy day my friend Please share with me your good ideas

@iIiWARHEADiIi 5 жыл бұрын

Бронзу нельза как и латунь. Они содержат медь, а это яд для аквариума и тем более если это креветочник. Так еще они могут содержать свинец, нужно искать пищевую. Нержавека пищевая может быть. Но опять же для человека может и не смертельно, а вот для маленького замкнутого водного объема это вопрос.

@seenakudel 4 жыл бұрын

So much knowledge that you give me about fish tank and accessories sir.. thank you so much!

@pieceofpaper924 4 жыл бұрын

Thank you very much Have a nice day My Friend

@ockietheron6916 3 жыл бұрын

Very good, thanks. I will use is for cooling the water of my 4 Tower hydroponic setup.

@nanoaquamania 4 жыл бұрын

Water cooling for hot side is really good idea, better than fans, just space consuming consuming.

@erlwij 5 жыл бұрын

Nice video, IMO this is better than the heatsink fan version with all the fan noise. Need to check if the water cooling for the hot side is sufficient though, otherwise it wont last. Thanks for sharing practical sample u had done. I will try this myself with some adjustment. Cheers.

@pieceofpaper924 5 жыл бұрын

Yes Thank you very much If the hot face is well radiated, the cold side will be very cold The highest temperature of hot water I measured reached 45 degrees Thank you very much Wish you a happy day my friend

@fredveto49 3 жыл бұрын

GREAT TUTO .... clear and practice

@pieceofpaper924 3 жыл бұрын

Thank you very much Have a nice day My Friend

@MrRlazarev 5 жыл бұрын

Отлично! Как вариант можно для холодной части использовать фильтр, а контроллер использовать для элементов Пельтье и помпы на горячей части. Great! As an option is possible for cold part to use the filter, and the controller to use for elements, Pelt`e and pump on hot part.

@pieceofpaper924 5 жыл бұрын

I apologize for my late reply because I have been in the hospital for the past few days Thank you very much Have a nice day

@amneziaxeaster-gaming382 5 жыл бұрын

If it cools the water too quickly it can stress the fish and even kill them! So it work really good on the big tank of 180 litres!

@kamaljyotikashyap9846 4 жыл бұрын

How many degrees did you win

@mr702s 4 жыл бұрын

You shouldn't mix raw aluminum with aquatic life. Similiar effect can be achieve by applying thermoelectric cold side to side of sump filter tanks except thermo exchange will be much slower.

@flighttracker2996 5 жыл бұрын

Have to agree, a bit heavy on the thermal paste. Interesting idea for a heat sink, a container of water. Might be able to make some cups of tea :-)

@pieceofpaper924 5 жыл бұрын

Thank you very much I will try to do better Have a nice day My Friend

@Cyptech 5 жыл бұрын

dude.... you applying thermal paste like nutella. thick layer of thermal paste make effect of isolating instead of transfering heat.. also your thermal paste is not effective, try using liquid metal or something bettter will improve efficiency

@pieceofpaper924 5 жыл бұрын

Yes Thank you very much for sharing your thoughts with me I will do better in the next test Thank you very much Wish you a happy day my friend

@royan.jdm2 3 жыл бұрын

Can anyone mention any liquid metal paste brand? Pls

@Cyptech 3 жыл бұрын

@@royan.jdm2 thermal grizly or cool labotry

@lachezari7957 4 жыл бұрын

i think if you connect the cold water pipe to the canister near to the aquarium inbound. Then for the hot water add a aluminium radiator or even a water cooling radiator just one like PC liquid cooling and then connect this pipe to external water source as you did may increase efficiency a lot.

@aigomorla 5 жыл бұрын

You cant use Alu or Copper in a fish tank... The alu will find something to oxidize like steel impellers, and then cause corrosion which will end up killing everything in your tank. Brass is fine if you have no snails / shrimps as it can potentially leech copper. If you can find a titanum or stainless steel waterblock, it will work, otherwise your asking to kill all your fish. Do research on what is considered SAFE metals in a fish tank before you recommend people doing it.

@diegochinchilla3209 4 жыл бұрын

Did you were able to get a titanium cooling block ??

@LilyNormand 4 жыл бұрын

Thanks for the video. Perfect! Have you tried to use the blue radiator with, instead of a water-pump ... an air-pump to get cold air ? I am curious to see if I can get the cold air from the Peltier module using a radiator with air-pump to build a small fridge. Do you think it might works ? Thanks!

@GM_handle22 4 жыл бұрын

Thanks a lot man.. you saved my money, what are all idea i have in my mind you tried out and gave the results. 🤩

@sumalsebastian 3 жыл бұрын

It works but not efficient and things become clumsy and it partially reduces appeal of the fish tank. More over this can be used in either a single medium tank or two small tanks. I used ups to power these thermo electric coolers incase Power cuts happen. Hiding everything in a separate box is the key to make it look better. Go for it only if you really need this like shrimps and sensitive fishes.

@macrie123 5 жыл бұрын

Hey man, you could make millions in the hydroponic industry!! Just remember who told you that!👌🏼 Great work

@pieceofpaper924 5 жыл бұрын

Thank you very much Have a nice day My Friend

@andresmurillo476 4 жыл бұрын

the second water look, you need to cool that water too. This will not scale well if you are not removing that heat. Would have been better using regular cpu fans for the TECs hot faces or using a radiator with fans in the heat face water loop. You would have gotten better quite better results. Excelent work.

@pieceofpaper924 4 жыл бұрын

Thank you very much I just want to do experiments to share with people about them Have a nice day, my friend

@hotcoffee1068 4 жыл бұрын

but a good silent fan is expensive, why don't you make couple of stages basin with a very thin layer of water. theoritacally it will cool much faster

@royan.jdm2 3 жыл бұрын

Water cooling is better than just a cooling fan.. Like a car radiator.

@sv1aaw 4 жыл бұрын

I dont have words, just amazing my friend. Thanks for the idea

@pieceofpaper924 4 жыл бұрын

Thank you very much Have a nice day My Friend

@muhamadal-fatih3894 3 жыл бұрын

Where can i buy this tool...?

@ShusteRium 2 жыл бұрын

Awesome video 🤙 Based on your test I Made cooling system based on platier For my 220 liter tank

@happythings2773 2 жыл бұрын

So did it worked?

@md.tanveerrahman4153 4 жыл бұрын

That's an amazing & interesting project. Simply brilliant. I am staying in Bangladesh where I don't think I can get all the tools required here. Can you please help whether those would be available in Amazon or eBay from where I could bring them?

@user-cl9go8sm7u 4 жыл бұрын

Крутая идея 👍

@kimnue 3 жыл бұрын

so u use one more water block and pump for reduce heat too. does it better than fan

@pieceofpaper924 3 жыл бұрын

My friend These are just tests requested by everyone I have not tried using it for a long time But the water will be better, but the water will evaporate and the radiator fan will be different

@ringfirdaus5325 4 жыл бұрын

a great idea and very kreatif..itu long white box what ... provide the name of any material that is in vidio ... I want to try at home ...👌👌👌

@pieceofpaper924 4 жыл бұрын

Thank you very much Have a nice day My Friend

@sonuhazra9026 3 жыл бұрын

Super video

@pieceofpaper924 3 жыл бұрын

Thank you very much Have a nice day My Friend

@blu313 4 жыл бұрын

Hi there, thank you for you effort, what a nice video. Its inspiring for those who wants to use DIY feature on their project. 👍 So the idea on your video is to pump the cool water from your tank through the warm side of the peltier into the water bin, and pump the warm water from the bin into the tank? Is this correct? Can I use DIY external filter (without filter media) for the water bin? I have built a chiller using dc fan, peltier and heatsink, but its so noisy, I can't stand it. And also its not effective since in 12 hrs the temp only drop 4°C from 30° to 26°. I am planning to follow your video. But I still can't understand how it works. If its not to much trouble, could you please explain it for me? Thanks a lot. 🤝

@diegochinchilla3209 4 жыл бұрын

Did you solve it? It work? I’m trying to do the same thing

@hadighaemipoor6354 5 жыл бұрын

My frend your film is very good & your work is carful tank you.

@pieceofpaper924 5 жыл бұрын

Thank you very much Have a nice day My Friend

@ProfinIn 3 жыл бұрын

Hello, sir. How it is possible that we all know a peltier has also a warm side yet you attached also same bar on the warm side but stll can produce decent amount of temperature? Does the wirings do the trick? Ty

@suanhak 4 жыл бұрын

Can you please prolong the yellow read information ormany diagram longer . Few secound is too short . Please make it at least 10...15 sec. Great job. Thanks

@cidskie 5 жыл бұрын

XH-W1209 Temp. Sensor Controller max only 20A , 4-peltier is 24A, will it burn the relay sensor?

@pieceofpaper924 5 жыл бұрын

I think it can't burn the sensor It only makes the Chip Chip inadequate I apologize for the late reply Because last time I was in the hospital hAVE a nice day My friend

@Rene046 5 жыл бұрын

it could also be possible to reverse polarisation so you can heat your tank .......

@pieceofpaper924 5 жыл бұрын

^^ Maybe I will make a video about your idea in the winter Now in my country it is summer Wish you a happy day my friend

@MrOnlymoin1 4 жыл бұрын

simply awesome!

@pieceofpaper924 4 жыл бұрын

Thank you very much Have a nice day My Friend

@razibislam6886 4 жыл бұрын

Did not understand the wire management from 4:10 to 4:37 how did you connect the cables with power supply.

@adesyafrizal3715 3 жыл бұрын

Please advice sir... i have the same question ?? And please tell me the spesification power supply ..

@rezaali3740 3 жыл бұрын

He drew the diagram wrong obviously. The thermostat comes in between the power supply and the electricity

@ianrafaeltoh7679 2 жыл бұрын

It's a perfect substitute for chillers if you have a 10 gallon tank or 5 gallon tank. Using a chiller on such a small tank is overkill.

@Дмитрий_Ф 4 жыл бұрын

Спасибо за идеи.

@pieceofpaper924 4 жыл бұрын

I apologize for the late reply Thank you very much have a nice day My Friend

@rogeliomorales5970 5 жыл бұрын

could you make a video for how to make an rimless aquarium??? many likes

@pieceofpaper924 5 жыл бұрын

I made that video You can see it here kzfaq.info/get/bejne/m7iUqqSQudLQXY0.html Thank you very much for supporting me Wish you a good day my friend I apologize for the late reply Because last time I was in the hospital

@5020886 2 жыл бұрын

This is just great !!

@GJoeTeo 4 жыл бұрын

Thanks for sharing this videos. It's very interesting. In your video Aquarium model 7 you've used air refrigeration for the hot side of chip-peltier. why you don't used in this case. Is less efficienty than flow water?

@pieceofpaper924 4 жыл бұрын

Thank you very much I just want to do the experiment and share my test with everyone Have a nice day, my friend

@xiangzhouang380 5 жыл бұрын

I wonder if the inlet of the heat cooling block can use the water from the water supplied by the chilled water. Meaning, pump water runs in to the inlet of the heat block, outlet of the in block runs to the inlet of the cooling block, then the outlet of the cooling block runs to the tank.

@pieceofpaper924 5 жыл бұрын

I am sorry but I do not understand what you are trying to say to me I apologize for my poor English skills Please speak more clearly Thank you very much Wish you a happy day my friend

@panjimartiandaru3081 5 жыл бұрын

That would mean the heat taken would back to the water cooled with the peltier.

@Ttblondey 3 жыл бұрын

Thanks

@pieceofpaper924 3 жыл бұрын

Thank you very much Have a nice day My Friend

@aquathoughtsforyou4434 2 жыл бұрын

Can I run this 24/7 ? Does it consume lot of power

@pieceofpaper924 2 жыл бұрын

Actually, I just did a test for everyone about its effectiveness If you actually use it, you should use professional equipment like that to save a lot

@tyabrahamse2461 4 жыл бұрын

Nice! Just check out how to apply thermal grease.

@hongquantruong6440 5 жыл бұрын

Mình có làm như bạn nhưng ko hạ được nhiệt vì bên tản nhiệt nước bị quá nóng không thể làm lạnh được như bạn. Không hiểu lý do tại sao. Bên bể chứa nước tản nhiệt dung tích bao nhiêu lít vậy bạn? Học cách phát âm

@pieceofpaper924 5 жыл бұрын

Bạn chỉ nên làm cái này cho hồ nhỏ thôi Hồ to như của mình không được đâu dùng lâu lắm Như trong Clip mình cũng đo bên thùng nước nóng lúc nhiệt độ cao nhất là 45 độ mình phải thay nước trong cái bể nóng vì mặt nóng càng được làm mát thì mặt lạnh càng lạnh Nhưng mình thấy nếu nghịch mà hồ nhỏ thì làm cái thùng xốp bỏ đá + nước như clip sau mình làm ấy lạnh nhanh mà đỡ tốn kém hơn nhiều

@AquarioMarinhoDescomplicado 7 ай бұрын

Eu tambem estava pensando em fazer um projeto desse para meu aquário. Mas pesquisando soube que o aluminio liberado pelo "water block" faz mal para os peixes e corais. Por isso ainda não fiz.

@TrangNguyen-jl8vb 10 ай бұрын

Hello, I want to ask, which one will be more effective when using 1 100w chip versus using 2 50w chips?

@devittentapramana7536 4 жыл бұрын

Is the water on the other tank not going to boil up? Cuz what I know is, peltier are produce cold on one side and heat on the other side. If its getting to hot, the other side will less to produce cold. Does the other tank do that job?

@bluecavemen Жыл бұрын

I wish he had a drawing how it works. Because one side should be hot while the other is cold. Not sure how he has this cool without having a heatsink to get more cold then hoy

@shivSingh-ht4gl 2 жыл бұрын

Nice

@KetansaCreatesArt 3 жыл бұрын

Hello Piece Of Paper, Such a great idea. Idea from Piece of paper to practical reality 😎 Please let me know- 1) Does this setup can work 24/7 at desired cooling effect without issues? 2) Did you try setting much lower temperature like 5 degree C? 3) Is the hot side portion enough to disipate the heat? Or do I need to attach heatsink and fan, if I want to run it for 24/7? 4) Is 5 litres water enough for cooling the hot side? Thank you

@suryadipdas984 2 жыл бұрын

Hello Ketansa, I also have similar setup.. if you use 5ltr water for the hot side, after some time the water will boil.. that I can assure you 🤣

@KetansaCreatesArt 2 жыл бұрын

@@suryadipdas984 , I also did it later on. Used 5 peltier cooling modules with 2 heat syncs and a fan for each. A can of water with submersible pump. Also got 33amps power supply. An exaust fan to blow cold air in front. Then dismantled the unit and used it in a thick wall thermocol box and turned it into a fridge. Total waste. These videos are just for fooling viewers to get views.

@randomdutchguy 3 жыл бұрын

Ok.....so many quesions. Why a waterblock on the cold AND hot side of the peltiers??? Is that why the extra water tank is needed??? Why not a heatsink and a couple if pc fans. Would that not eliminate the need for that water buffer? Maling it all more easy to use?? The controller looks interesting

@giadagarbo9155 4 жыл бұрын

Hello! Amazing video and work. I have a 200 liter fish tank. I can use the same elements or I have to boost up them? If yes, what do you suggest me? Thank you so much

@kamaljyotikashyap9846 4 жыл бұрын

Im curious too

@m.yossipratama4514 4 жыл бұрын

its working, thanks

@pieceofpaper924 4 жыл бұрын

Thank you very much Have a nice day My Friend

@hobbyman1971 4 жыл бұрын

That’s a wonderful project bro! Where did you buy all the components for this project? Thanks

@t.c.baquariumfish3423 5 жыл бұрын

GOOD VIDEO 👍

@pieceofpaper924 5 жыл бұрын

Thank you very much Have a nice day My Friend

@kishanmunjapara5216 3 жыл бұрын

super dupper ...🔥🔥

@asepsuherlan-cn2px Ай бұрын

mantap sungguh ribet mau nyari dingin 😂😂😂. di tempat ku suhu 24 derajat cukup pake kipas fan aja

@edevaldosantos1235 Жыл бұрын

Hello my Brother, I hope all is well with you! Can you tell me if this project serves to heat the water in the aquarium as well?

@waterblock20021 3 жыл бұрын

To purchase these products please visit our website : hariimpex.online

@orlandobanderas Жыл бұрын

El aluminio de los bloques de refrigeración es toxico para los peces?

@deta3d215 4 жыл бұрын

i have smilar idea but without cut off module ( i dont know whats the name of the module ) , i want to make one tank with temp as lower as possible, thank you , your video helping me :D

@nazirulhariz5256 4 жыл бұрын

Sir, If I want to increase the water temp, thats mean I need to use the hot side into aquarium am I right?

@pieceofpaper924 4 жыл бұрын

Basically right But if you want to increase the temperature of the tank you have to use dedicated heating for the aquarium, because the heating of the aquarium is much cheaper and also more energy efficient. I am sorry for the late reply Thank you very much Have a nice day My Friend

@nazirulhariz5256 4 жыл бұрын

@@pieceofpaper924 noted..thanks sir

@alvelloso 3 жыл бұрын

Hello friend, great idea, congrats! Don't you see any problem with the use of an aluminum cooler in your tank? I hear it's harmful to the fish. I wonder I could have a stain cooler on the tank size. Cheers !

@MithinXavier 3 жыл бұрын

This alluminium water block safe for fish

@udaydas6291 3 жыл бұрын

One water block will work? one peltier how litters water will cool?

@jongchunjin8927 2 жыл бұрын

hello there, I have been follow ur video and did everything same as you but I have been end up the temperature only drop for 0.4C(28 C room temp) for almost 1 hour and the hot water goes up to 40C, I wonder whats the problem actually

@orlandobanderas Жыл бұрын

Is aluminum from cooling blocks toxic to fish?

@stephaned8198 5 жыл бұрын

Les plaques à effet peltier c'est un côté est chaud et l'autre est froid normalement donc il devrait y avoir un dissipateur d'un côté plutôt qu'une pompe ???

@pieceofpaper924 5 жыл бұрын

In this Clip I just want to test people to see how the heat dissipation works So I used both radiators with water Thank you very much Celebrate you a happy day my friend

@ramesh10829 5 жыл бұрын

The other tray contains heated water, so is it not bad for the peltier if it's not cooled. Heated water will be circulating in the other heat sink

@pieceofpaper924 5 жыл бұрын

Thank you very much Have a nice day @Ramesh Balakrishnan I apologize for my late reply because I have been in the hospital for the past few days

@ramesh10829 5 жыл бұрын

@@pieceofpaper924 you have not answered my question

@pieceofpaper924 5 жыл бұрын

I'm sorry but I don't understand what you want to ask me I apologize because my English is not good You can speak more clearly Thank you very much

@wardraven8755 5 жыл бұрын

The peltier gets could but needs heat to work

@ShrenikBhura 3 жыл бұрын

@@ramesh10829 the dtmax of the peltier 12706 is 60-70 degrees. So the difference between the cold and hot side needs to be managed to an extent that the target cold water temp is reached. Hence when the relay is cut off, the radiator tank get a chance to naturally cool down a bit. Yet I think it can safely increase till 50 degree c. Basically it seems that it works great for this use case. I want to employ this technique for outdoor hydroponics by using water in an earthen pot as a radiator. Have a hunch that it will work.

@BuildersBench 3 жыл бұрын

does the other tank with hot water gets hot enough? if so, can it be cooled passively? thanks! very interesting project! :)

@adpaquastudio 3 жыл бұрын

But for this we need to have another tank with water .. is there any idea without using extra tank with water .. ?

@alfonsusboy9375 2 ай бұрын

I was try this way, but I didn't see any water temperatire goes down, on water flow the cold water block goes up the temperature, without water flow water block will cold, with water flowing it does not cold, to make water cold need time to hold time for the water to stay on cold water block, and that is need to delay up to 10 second, if flowing and flowing it does not happen, water stay on last temperature, will not cooling

@abal2studio 4 жыл бұрын

Thank's Bro.

@SubhanToba 4 жыл бұрын

Can i use jerry can as reservoir for the cooling water (hot side) or it has to be open reservoir?

@pieceofpaper924 4 жыл бұрын

I only know if the hotter side of CHIPTEC is cooler, the cooler side of CHIPTEC will be colder Thank you very much Have a nice day My Friend

@prm6463 5 жыл бұрын

Awesome

@pieceofpaper924 5 жыл бұрын

I apologize for my late reply because I have been in the hospital for the past few days THANK You very much Have a nice day

@harrybeta 3 жыл бұрын

Cooling the fish tank water must be slow,otherwise fish could be sick.

@pieceofpaper924 3 жыл бұрын

Thank you very much Have a nice day My Friend

@khanhtran2213 4 жыл бұрын

Bạn ơi bể 60 40 40 thì nên dùng mấy con sò 60w hả bạn

@pieceofpaper924 4 жыл бұрын

Cảm ơn bạn nhé Mình cũng không chắc lắm Cái này mình chỉ làm thí nghiệm cho mọi người thôi Nhưng máy lạnh cũng như sưởi Nên dùng thừa công suất một chút thì đỡ tốn điện chứ dùng thiếu công suất thì tốn điện lắm mà cũng không hiệu quả

@ShyamsundarPK 4 жыл бұрын

Is that titanium make? Can we use it for saltwater aquarium?

@diegochinchilla3209 4 жыл бұрын

Did you find how to make salt water aquarium work?

@ShyamsundarPK 4 жыл бұрын

@@diegochinchilla3209 no not yet.

@diegochinchilla3209 4 жыл бұрын

Shyam sundar after several Days trying to solve this problem, I came up with the idea of making my own cooler

@diegochinchilla3209 4 жыл бұрын

Shyam sundar I’m gonna make it out of thin layer of glass. Doing it like that, is gonna make me let use the same design of the video

@ShyamsundarPK 4 жыл бұрын

@@diegochinchilla3209 kzfaq.info/get/bejne/hJ-gY7OelrXPmGg.html This link may help you. But we can't find the titanium coil which he used.

@sunilnirwana2131 3 жыл бұрын

Great vedeo.Can you share the specs of power supply module.Also if the ciculation tank is placed 2 ft below the fish tank,than would you require a more powerful pump in it?

@sansyt0 3 жыл бұрын

Hi. If you used 3 modules for 100 liters, is one tec1-12706 module enough for a 30 liter tank? Edit: I'm okay with 1°C drop per 1-2 hours, just need to drop temp enough

@aryakusumamade1663 5 жыл бұрын

what is the type Switching power supply you use, and what name the blue box ?? Thanks

@pieceofpaper924 5 жыл бұрын

That's the power supply 12v 20a And the blue piece is Aluminum CPU Radiator Water Cooling

@aryakusumamade1663 5 жыл бұрын

Piece of Paper Thanks Bro 👍

@Salibs 3 жыл бұрын

isn't one side of the peltier hot and the other side cold? you got one plate to the cold side and another plate to the hot side?

@GiovanniAMarletta 4 жыл бұрын

ciao, can you publish the list of all pieces/leads liks for buy ?

@lequangvinh9x 4 жыл бұрын

cái hộp mầu xah có 2 đầu in out đó là thiết bị gì và có thể mua dc ở đâu hả anh. Em cảm ơn

@pieceofpaper924 4 жыл бұрын

Cái đó là cái tản nhiệt dung dịch của máy tính Mình chế thử nghiệm vậy thôi

@tanmaysarkar7342 Жыл бұрын

I am sorry but I tried to cool down my 50ltr tank with 3 peltier 12706 but the temperature is not decreasing after 27degree centigrade... Help me with some information

@imayavaramban.r7555 4 жыл бұрын

Nyc work bro.. ur channel name in d video is sometimes hiding d information in video 5:51 temperature is not visible. And temperature in that white colour monitor is dull use any lights 9:51..

@micio_solo 4 жыл бұрын

nice, thanks for the idea mate)

@hadighaemipoor6354 5 жыл бұрын

So good

@AjiNewbieGaming 5 жыл бұрын

Is the maximum limit of the use of peltier only reaching 26 degrees or can it be lower for example 10 degrees for the water the size of the aquarium?

@pieceofpaper924 5 жыл бұрын

Thank you very much Have a nice day My Friend

@matafungsi89 4 жыл бұрын

no.. it can be as lower down to -12 celcius

@rohitmohan2916 4 жыл бұрын

What is the max temperature of the hot water produced ??will using automobile coolant cause a better radiation??

@chriszampoulis8719 5 жыл бұрын

With only one of this blue radiator with three peltier and one pump to regulate the water won't work? i don't know if you understand me.

@KODAfail 5 жыл бұрын

hello friend, excuse me if i got you wrong but i think you have the same missunderstand that i had he uses 2 blue radiator because one side cools the water and the other side warms the water peltier works as one side of it getting cold and the other hot Ive seen many projects where they use an fan or heat dissipator on the hot side but it seems that also using water in the hot side works better thats why he has 2 tanks of water. 1 gets cold and the other gets hot hope i could make it clear

@pieceofpaper924 5 жыл бұрын

Yes I just want to do a test on the types of radiators I found it better to use water radiators We can do more neatly during use You must have a temperature controller like mine The temperature controller controls the machine when the temperature exceeds the required level

@chriszampoulis8719 5 жыл бұрын

I understand how the system works. I'm just saying that if a radiotor with its both sides have peltiers to cool water and the hot sides of peltier have heatsinks. Then you need only one pump to regulate the water. I have a diagram. Add me as a friend to send it to you!

@bangzed1502 3 ай бұрын

I was try. This is not efficient for my tank. Power consumption so high and cooling process too long. Now i just using fan only and the result is good for my tank ❤

@harishanker3848 3 жыл бұрын

Can we connect the pump also to the thermostat so that it will auto cutoff it?

@techwrecker9518 3 жыл бұрын

What did you use for thermal paste? I have spent an entire day searching and the best idea I had was thermal pad.

@johnnikc2454 Ай бұрын

this 100liter or below60 liter?

@robertehlers4330 8 күн бұрын

Tryi g todo this with studd i have already ihave wires pup s and fitti gs laying around but need to builtfor 0 bucks i dont have nk more miney and need water temps dows i ha e lost 30 plants in last 2 weeks please help need more step by step for am iddiot like me

@sv1aaw 4 жыл бұрын

I wonder where you find the water cooling for the Thermoelectric. With two of TEC1-12730 you can make a chiller almost 0.5 kW the problem is the 12v DC too much Amp