I could watch AvE unbox anything, the brutality, the haste, no bucking around for 14 minutes before the box is even in shot. 10 seconds in and its done

Anyone else waiting for him to cut somthing important off when he opens the box.

It's adorable to hear your tone instantly change when your daughter is in the room

I bet I emptied 1000 dead water heaters with that M18 transfer pump. It would pass some pretty gnarley chunks. Obviously, I eventually forced the smoke outta it. Pretty skookum choocher in my opinion.

My wife was listening and laughing from across the room, "what's he breaking apart now?!"

" I could pull it out and show you...but then you'd feel bad about yourself. " Oh AvE.☺

As a life-long Californian, I can confirm that it is rough living in California. Every day I get some form of new cancer and it's truly horrible. If only these chemicals weren't recognized to be carcinogenic by my state...

Living in California is pretty rough. Everything is expensive and covered in avocados and fire.

$10 for the drill pump, plus a zip tie or hose clamp to keep the trigger down. I just saved $90, and opened myself up to a bunch of liability!

i want to see some corn running through the window.

I don’t know much at all about tools but I find these videos highly satisfying and they help put me to sleep at night.

EVENNNN FLOOO-OOW

28 minutes worth of pumping is all I can usually manage before the nuto wins, even on a full charge myself.

I just bought this pump a few days ago for filling rads on heavy equipment. Running out of a 1000L tote with 3/4 hose on each end (pushed over a NPT nipple as you have in your set up). I measured the drop in height over 1 minute filling another vessel. The markings on the side of the tote are 93MM/100L. I measured a 31MM drop in 1 Minute. That works out to about 33.3L/Min. On a single mostly charged Max 5.0 I pulled 500L out of the tote and lost only 2 bars from not exactly fully charged battery. For the purpose I am using it (filling rads on 100L+ systems) this beats waiting around for the lube truck. This instance i actually filled the lube truck as a way of testing the pump. I only geeked out and measured some shit because of your video's. thanks Uncle Bumblefuk

"it must be rough living in California" I can attest that you sir, are correct.

"Pixie choreography department" -- I about died XD

Once upon a time, when I was a wee lad....I was at the Sta-Rite plant where they were testing the output of their pumps and they test them with a column of water and the LARGEST diameter pipe that the bung is threaded for. So we are talking positive head from the water column throughout the duration of the test and zero restriction from the plumbing fittings on both the suction and discharge lines. Positive head is the magical formula that will give you those numbers, plus increasing the size of the suction line.

Great video as always my man! I work on wind turbines. I use this pump off and on for coolant. It is great for that. Drill pumps weren't functioning. I bought this pump since I have other Milwaukee tools. It does what I expect, every time. Self priming, use XC5.0 mostly but have a XC8.0 as well. I will try it next time I have a big hydraulic leak (Mobil DTE) to see if it can help transfer the waste hydraulic as well. As far as Castrol X320 gear oil I doubt it can move gear oil, but maybe worth a try. I have had nothing but suffering with "drill pumps" Maybe they were all cheap , poor quality. But yeah hate even thinking about drill pumps. I really have learned quite a lot from watching your posts. I honestly appreciate your input into the world. Thank you AVE!

You were talking about the old Detroits diesel, the old man was telling me a story about him and a few friends rebuild a 12-71 and slapped in a needle nose pete. On the first fire up they didn't have any batteries to spare so they decided to pull/push start and park it to break it in. So they let someone who never seen a semi truck before hop up in the cab to dump the clutch, so he slapped it in "first" fired up first pull. After the break in dad jumped in the cab and went to put it in gear, let out on the clutch, and the truck went in reverse, so he slid it in reverse and it went forward.

I have only heard my dad and myself say “Drier than a popcorn fart”. I’m so glad I subscribed to you!

Random nugget of info - in the UK those engraved Lamicoid signs are known as Traffolyte. Grandfather worked at De La Rue, when they got out of the business of custom engraving in the late 60's he picked up a machine and a load of stock and made a decent business of it.

Mr. AvE, From an aspiring engineer about to finish school and an amateur shop rat, i've got to thank you for the time you take to explain all of what you do. Your words of wisdom are incredibly valuable and encapsulate exactly what makes engineering/manufacturing exciting in the first place. Your sense of humor is always a delight as well. Keep choochin the way you do.

I might add that the near useless Booch Micro Chainsaw does one thing exceptionally well..and that is slaying any cardboard power tool box in 4 seconds flat lol 👍

Aw I really like how she knocked as to not just interrupt you, you raised her well.

Beautiful morning. Sitting in my recliner with a big bowl of cereal in my boxers and skookum shirt when a notification for this video pops up. Time to start drinking.

AVE - You need to use a 3/4" ID hose on both sides of the pump to get the full flow level that is claimed on the box. It looks like you have a smaller 1/2" ID hose in the video. 1/2" is a much smaller flow area, and this smaller flow area is restricting the flow rate. Try the test again with full 3/4" hose directly on the pump head and you will achieve the advertised flow rate.

man the amount of knowledge you have makes me feel bad about myself as a senior mechanical engineering student

Cant believe you were huffin plastic for us. Bless your heart.

Test an automotive winch. I know it's not a hand tool but I bet a ton of people will be interested in it and how much it can really pull

I suspect that if you were to attach the original fittings with 5/8" garden hose, as it was designed for, then your flow would increase dramatically. There is a lot of restriction with all of the fittings, valves and what appears to be 3/8" hose. Just my 2 cents on the subject.

The amount of knowledge I get from these videos is so awesome!

Cheers to ave for another robust video. As someone who relies on tools like this to feed my family it’s nice to get a good look under the skirt at the beef curtains. Keep up the awesome work!

But the drill one is exactly what zip ties on the drill trigger is for.

A quick check for ABS is acetone. If it goes tacky after you've put a dab on then it's ABS

My guy your video by the manufacturers is quite literally the best idea ive heard in a long time.

When I worked in the plastics factory, as a die setter / process technician many years ago, I learned to identify many different Plastics based on their smell if you burnt them.

The Milyuckie test facility must use a 200' water tower on the supply side

_Richard Head of Marketing_ LOL!

You opened that box like a champion 🤘🏼

AvE is like a somm for plastics. Truly a man of culture.

-10 for singing. +100 for the song choice. Also: Green is 30 amps.

Very, very excellent careful teardown & defect analysis. Milwaukee needs, needs, NEEDS someone like you, in charge of their QA.

i never laughed so hard until i saw the start when you chainsaw the packaging hahahahah

Thx for the o-ring advice. I've done that more than once!

My Thinkpad is, as I can confirm, *JIZZ* proof. Take that Apple.

Jeezless!! You touched it with your bare skin!!!!! RIP

I always loved starting my 8v92 and finding that I have one forward gear and eight reverses in the Eaton-Fuller. Fun times when they start in reverse

Thank you for the videos AvE. You have helped more than you know and in more ways than one.

I've combined brass and aluminum garden hose fittings before. The damned things eventually weld themselves together and there's no separating them without irreparable damage. I've learned to always use Permatex aluminum anti-seize lubricant.

Commented the other day that my solar 'batterias' are charging like they should. Wife looked at me like a deer in headlights. "AvE" I muttered. Wife walked away shaking her head.

By far the best beginning of any unboxing on KZfaq

"aaaaaah now i'm gettin' all my flavors muddled" oh man i love your videos

"The pixie choreography department" ie: the circuit board. Classic!

AvE I love you man 😂😂😂 You remind me of the Mechanic I trained under during my apprenticeship. Made me the mechanic I am today and thought me a whole new level of swearing 😂😂😂

Ive been using these 3-4 times a week for oil changes...works great for what it is. 5 centistoke to 68 is most common but it will even pump 320 gear oil. there is some type of high current shutoff...so then you have to sit there turning it on and off...but it does the job 4 batteries later I adapted an inliner filter to it so we can prefilter our oil...and the pump seems to handle it alright. We carry spares for the inevitable breakdowns lol...talk about running gear hard and putting it away wet. Awesome to see how its made.thanks ave!

Good lord man!! Its 1130 at night I was half asleep scrolling thru KZfaq.. that intro! HELLO!!!

They don't run a physical test. It's all just calculations based on pump volume, motor rpm, etc.

They found you? RUN FOR IT MARTY!!!

Taken from the electronic systems evaluation course I took with the US government, there are ways to test a system which are advantageous to the supplier. Unless you specify the methodology used to test a system, the manufacturers will ALWAYS use a test which does not conform with what will be experienced by the user.

You have an original way of unpackaging things! I've got to try it too..

Have you been losing weight? Bare wrists are looking a little more streamlined.

All of their specs are probably "under ideal conditions". So their throughput values are probably pumping water with a bit of "gravitational assist". I noticed that your inlet was creating some good momentary vacuums, creating vapor bubbles, and taking up volume in the pump that could have been used for liquid water.

Unboxing using the ultimate unboxing Bosch tool that previously got a slating. You got to love it.

Have worked with marine sea water pumps for years. Impeller don't care which way it turns, it will flip the vanes in the proper direction when the engine starts. Lots of diesels, when stopping, will run backwards part of a revolution (due to cylinder compression), so the seawater pump impeller could be flipped backwards part of a revolution as it comes to a stop.

i mean considering it came in a box, why did it have to come inside a plastic bag too? is it that important to contain the smell of chinesium for the end user?

Very nice teardown video!

As always, I enjoyed the hell out of this, and all of.your other episode’s. My guess as to the exaggerated performance claims would be zero restriction or turbulence of any kind. And by that, I mean no fittings or valves that are less than full port. And as far as the discharge, I’m sure they advertised the best results of GPM and PSI under two totally different scenarios, but neither at the same time or test. I very much appreciate you’re video’s and twisted sense of humor! I wish you were my neighbor. I’ve been shopping at the same sort of industrial gettin spot for 23 painful years, and am now overwhelmed with tube drive and digitally controlled hydropneumatic ingredients of all kinds. Thanks Again, Troy.

I have used this pump for work now for a a few months now and it is surprisingly sensitive to using smaller diameter hoses for pumping. I use to use some older washing machine hoses to hook up for transferring water around but they have an inner diameter of a 1/4" have since switched to short 3/4"ID garden hoses and it runs much faster. So for Milwaukee marketing test they may have had it piped together with 4inch fire hoses to get the number you see on the box.

"Corn kernels through the pump again?" If I had a dollar for every time my wife yelled that at me from the shower . . ..

The max flow numbers would be with no restriction on the inlet or outlet. Max run time would be done the same way. The larger a pressure differential the positive displacement pump has to create, the more work it has to do (less battery life). Higher differential pressures also cause more slippage which accounts for a loss of flow rate. These facts are true for positive displacement pumps, but not centrifugal pumps. They actually pull less current and do less work when you choke the outlet.

We've had one at my previous job for a over a year now. Used it mostly for pumping hydraulic fluid. It's been absolutely fabulous. Fuck the job to high hell, but that pump turned a two man job with a big ass air driven pump into one man carting around a 55 gallon drum with that chucked on top. Even worked fairly well to empty plugged drain pits in a pinch.

Opening presents at your house must be one hell of a party!

I lost it at "rectum frier." Its the most high brow scatological joke I've ever heard.

“dry as a popcorn fart” - hahahaha

You unboxing is therapy!

Fantastic start. You are awesome!

“Come upstairs and you’ll see!”, The most daughter statement ever.

Maybe that small diameter hose you have on the inlet is restrictive? Great work as always AvE keep it up

Best unboxing ever! Beautiful to behold AvE, just a beautiful thing...never gets old "Laugh Out Loud" Thanks you f@*k!!!

I frigging love the cordless box opener

I love the homage to +Louis Rossmann

To Milwaukee, Makita, Hilti, DeWalt, etc........."In God we trust, all others must bring data."

Thanks for the o ring tip! I learned something today and it isn't even 5:00 a.m.

You are the funniest, most knowledgeable guy i seen on youtube.. Nd your canadian so its even funnier. Lol. Im grom wisconsin so you have the accent everyone says us Wisconsiners have.

Thanks for a hilarious video mate. I laughed my ass off several times thru this one. Also thanks for a lot of usefull info.

With the inlet gauge showing nearly full draw I think there is a hell of a restriction on that side. Golf ball through a coffee stirrer?

Even though you dont call it an unboxing video.....you have the best way of opening a tool box.

Now THAT is how you unbox something! Straight to the point!

"Like any GOOD wife will tell ya" Excellent truth right there!

AvE smokes plastic to counteract the sheer bliss of being Canadian.

Freshwater. Coming from Minnesota, the land of a thousand lakes. Great vijeo as usual. Many sneaky sidewords in there I enjoyed.

My brother has written out several of them but still swears by them. I've used his once for a water heater replacement and it was terrific. I now own the ryobi and it worked great as well. For a often a I need a pump either one is far and away capable of doing the job. I'm not draining pools for crying out loud.

can you do more learnin vids Kahn academy type stuff your knowledge combined with the humor would be great

The important question is how much peanut butter can it pump per hour?

I used this to empty hvac emergency drain pans. It works great for that and saves me from emptying a shop vac 3 or 4 times. I might use it to empty water heaters faster when I replace them too.

Box opening took me by surprise, but damn I loved it.

Milwaukee probably tests the pump buy pulling from a tank 10 feet in the air. Hydrostatic assist.

I'm guessing their max GPH & GPC was based off a large diameter hose on the inlet and outlet (Least restriction possible) and a brand new battery. During your test you had the ball valve choked back on the outlet side creating back pressure, and small diameter hoses. Lots of restriction. A lot of times spec sheets are written to fluff up the capability of the item being sold, with a huge caveat: Not all specs can be achieved at the same time. Max head and max GPH are inverse to each other and therefore cannot be achieved at the same time.

Pure comedy, and educational material at it's best.