Curved Corner Self-Adhesive Vinyl Film Application (full) with Hot Tensioning

Рет қаралды 282,665

3 жыл бұрын

Here is the video that many were waiting! Thanks to our robotic friend Matthew, We will show you hot to apply our film on a curved corner without cutting into the corner. Be careful and follow all the steps to the end.

Пікірлер: 129

@donlunn792 2 жыл бұрын

The voice over sounds like a 1950s BBC presenter. But nevertheless a damn good vid. Now I know how I’m going to change my Kitchen cupboard doors. Thanks for the vid and great explanation .

@ARTESIVE 2 жыл бұрын

thank you!

@Keddemann Жыл бұрын

I thought the voice was Microsoft Sam

@Gecko12396 2 жыл бұрын

I did this tonight for something in my bfs van. Except I used my hairdryer to stretch and it come out perfect! Thanks 😊

@ARTESIVE 2 жыл бұрын

great

@ARTESIVE Жыл бұрын

it's okay, also the hairdryer is fine!

@kumiko4295 Жыл бұрын

Thank you. It's very helpful

@ladybugbecca8 Жыл бұрын

Super helpful! Thanks!

@jamesolelo4406 7 ай бұрын

So like any corner you just have to be careful and take your time lol glad I learned to do this on a car before building my own tables and drawers to wrap

@ARTESIVE 5 ай бұрын

we are happy for you!

@LittleLikeness 2 жыл бұрын

Brilliant solution with the heat gun for more edge control..thank you for this solution!

@ARTESIVE 2 жыл бұрын

Hi! Thank you too!

@oummouhamed2529 Жыл бұрын

رائع كنت أبحث عن الطريقة الصحيحة ووجدت هذا الفيديو ساعدني كثيرا بارك الله فيك وشكرا

@ARTESIVE Жыл бұрын

thank you

@franceb3156 Ай бұрын

Very helpful, Sir! 🔥

@justconcentrate9843 2 жыл бұрын

From my short but very successful experience with wrapping, I heat tension even the flat surfaces for a strong bong. I stary exactly as you with peeling off a small amount and folding but after the first initial full stick of that amount I move forward with heat tensioning the rest

@frasertones8519 2 жыл бұрын

My bongs are all strong.

@MGmirkin 2 жыл бұрын

My dongs very strong, too... [/sarc]

@ARTESIVE Жыл бұрын

thank you for your comment.

@jamesolelo4406 7 ай бұрын

@@frasertones8519mine too😂

@konradwarsiewicz5257 2 жыл бұрын

Great video thanks

@ARTESIVE 2 жыл бұрын

our pleasure!

@marshannajohnson8584 2 жыл бұрын

I feel cheated! I really would have loved to see how you put the film on the back side of the board. To see how you cut the film to make it look uniform

@ARTESIVE 2 жыл бұрын

check better, on final video we also show the bottom face.

@andyp9095 Жыл бұрын

Or you could watch the video again, and this time with your eyes open

@malteserjones1502 Жыл бұрын

@@andyp9095 😂

@lafleurk3727 Жыл бұрын

@@ARTESIVE you didn't show the back side process.. we see something perfect but dont have any idea of how to get a so beautiful finish

@debbiepoulter3790 Жыл бұрын

@lafleurk watch their curved desk video which shows you how to do the finished side. That's how I've just found how to do it.

@cinquentakhamseen3124 2 жыл бұрын

Wow! Thank you 😊

@ARTESIVE 2 жыл бұрын

thank YOU!

@Keddemann Жыл бұрын

What temperature should the heat gun be on?

@blogJM Жыл бұрын

Thanks chat!

@secession77 2 жыл бұрын

Great tutorial! Will this method work on a board with rounded holes inside? I want to wrap my radiator cover somehow. I think it would be much easier to hot tension all those holes than trying to trace and cut out the foil.

@ARTESIVE Жыл бұрын

hi, thanks. then , this is up to you. we suggest to test first in some part and then decide if this applications can be fine for your case.

@user-qz6ix7od3b Жыл бұрын

how did it work out ?! facing a similar issue. i will use heat to mold the film into the creeces, i don't know if this solution will last over the years though ...

@secession77 Жыл бұрын

@@user-qz6ix7od3b I gave up the idea of using the vinyl wrap at all. The adhesion was too weak on wood material.

@user-qz6ix7od3b Жыл бұрын

@@secession77 yeah, this just looks to be a short term solution. although i think it will last 2-3 years if applied properly, until i get the chance to remodel

@shekhargolapkar9074 3 жыл бұрын

Thanks. Very usefull tutorial.

@gregsanchez3553 2 жыл бұрын

Thanks for your tutorial on how to, Can I apply it to a painted but sanded surface and clean or I have to apply it with putty filler? thanks and Regards Sir Reed

@ARTESIVE 2 жыл бұрын

Hi, I didn't understand. If it is already filled and sanded, just use a primer before applying the vinyl.

@heavenscent700 Жыл бұрын

Hello I have an ikea cabinet door that is mdf. There are little parts that has already bubbled because of moisture. Can i still salvage it and cover with contact paper?

@APDDD555 Ай бұрын

Excellent tutorial! Thank you. What is the primer you refer to please?

@ARTESIVE Ай бұрын

Thank you, www.artesive.com/en/accessories/ here you are!

@superduperboyx Жыл бұрын

Nice video but I really wanted to see how you did the BACK part in connecting with the edge.

@user-qz6ix7od3b Жыл бұрын

would have loved to see that too. did you maybe see any other vid that explains properly how to do corners and edges ? thx !

@manmangy 9 ай бұрын

Excellent

@ARTESIVE 9 ай бұрын

thank you

@davidcatanach2620 Жыл бұрын

Cheers!

@mianbilal3397 10 ай бұрын

Best job

@ARTESIVE 9 ай бұрын

thank you

@josephyeomans1347 Жыл бұрын

Beautiful work! Haha

@ARTESIVE Жыл бұрын

thanks

@bribeavers426 3 жыл бұрын

Could we use a hair dryer instead of a heat gun? Thank you.

@ARTESIVE 3 жыл бұрын

absolutely.. anything that creates hot air is fine.. so also an hair dryer

@lpainter8008 Жыл бұрын

What if you have an inner curve on L shape desk that is also angled, about 30 to 40 degrees rather than a 90 degree edge to the desk top?

@gxvq Жыл бұрын

I have the same question!

@user-qz6ix7od3b Жыл бұрын

i would also like to know a proper workaround for this

@s.o343 Жыл бұрын

Is this film the same as contact paper?

@4tsixer 10 ай бұрын

Good vid, but it is a lot different when you cannot move the counter top into different positions.

@ARTESIVE 9 ай бұрын

needs a bit of experience. yes.

@jamesolelo4406 7 ай бұрын

You can't put it on another table and slide it to where you need to? Must be big or heavy

@qwertandrew8720 3 жыл бұрын

Can u make a video of how u apply the other side without seeing the attachment? Thank you

@ARTESIVE 3 жыл бұрын

what do you mean exactly?

@qwertandrew8720 3 жыл бұрын

@@ARTESIVE you showed that how you install the first side along with corners. At the end of the video, you flipped over to show the other side without describing it. I wanna know how did you cut the edges without seeing the attachment.

@THEGRAVOID Жыл бұрын

Just a quickie, What temperature should i set the heat gun and for how many seconds? Hehe

@ARTESIVE Жыл бұрын

normal temperature is about 150°C at normal distance, but it depends also about time you warm and distance.. make some test and find your ideal setting.

@McrAwSugarMCR 3 жыл бұрын

Hello! What temperature should we be using for the heat gun! Thank you!

@ARTESIVE 3 жыл бұрын

The temperature used depends a lot on the film, the distance and the work you are doing. Generally a temperature of 150-200 °C (300-400 °F) is used. However, it is possible to use a normal hairdryer, the time will be longer due to the lower temperature.

@hessulipoika13 2 жыл бұрын

Should you put some nails to really lock to vinyl on cabin?

@ARTESIVE 2 жыл бұрын

well, at the moment it's still there in right position without any nail.. maybe you are used to low quality vinyls.

@spaceunicorn8423 2 жыл бұрын

Hi, thanks for the info. Would like to ask. Can it be stick on a plywood or mdf board door.? Do i need to sand it and apply primer before applying this vinyl film?

@ARTESIVE 2 жыл бұрын

Hello. Yes it is better to sand it before.. On MDF surfaces we suggest to smooth the surface before apply the vinyl and use the primer especially on corners or edges, such our Magnum Primer for example. You can find it on our official website artesive.com

@vemulanagalakshmi163 2 жыл бұрын

@@ARTESIVE Can I purchase the vinyl in india ?

@shelyb3630 3 жыл бұрын

exilent

@adilh7121 2 ай бұрын

oh you are good

@queeniesharpe30 3 жыл бұрын

What about if you have curves and grooves in the middle of your doors I.e panelled doors

@ARTESIVE 3 жыл бұрын

Hi! Try these tutorials: kzfaq.info/get/bejne/gauPe5Vq3JvMYYE.html and kzfaq.info/get/bejne/gLNnl5h13cebZo0.html

@queeniesharpe30 3 жыл бұрын

@@ARTESIVE thank you that's really help full

@user-qz6ix7od3b Жыл бұрын

@@ARTESIVE thank you !!!

@MGmirkin 2 жыл бұрын

That AI-generated voice is **almost** believable... **Almost.**

@ARTESIVE 2 жыл бұрын

almost yes.. important is to understand the video

@aminasheikh5545 2 жыл бұрын

Nice

@ARTESIVE 2 жыл бұрын

thank you

@binodgurung3367 2 жыл бұрын

What if the surface is curved as like that of shield of captain america

@ARTESIVE 2 жыл бұрын

beside asking Iron Man, we should see how is the shape to answer you better. Please send us an email and we will reply you better.

@donlunn792 2 жыл бұрын

You mean using it on compound curves ? I would think that if it works on that fairly sharp,curved corner a compound curve would be easy,using the heat gun. I have to update my kitchen cupboard doors, and intend to use it on them.Every corner is a compound curve. Even on my old kitchen,the covering on the corners was beginning to de -laminate,where there was any heat.So even professionally made cupboard doors can have problems.But I am sure after a couple of failed attempts I will get the hang of it. Cheaper than replacement doors. Similar film is used on Cars ,and compound curves come in abundance on vehicles. Give it a go. Hope all goes well on your project. Don.

@andersjohannsen709 Жыл бұрын

Where can i buy the table overlay? Nice video - xx Anders

@ARTESIVE 5 ай бұрын

Hi, check www.artesive.com/

@markcook8526 7 ай бұрын

You sound like Hanable off of Silience of the Lambs!..Say Hello Carisse

@ARTESIVE 5 ай бұрын

we'll get over it

@RelaxingSounds-mj5mx 2 жыл бұрын

Can i share this perfect video?? It is really helpful!

@ARTESIVE 2 жыл бұрын

you can share the link, not copy the video or use for other reasons.

@stephenhamilton9791 Жыл бұрын

This is definitely one of them random things u go to do. Buy a heat gun, all the materials u plan to use and realise it’s actually like trying to speak fluent Chinese after 2 half hour lessons

@ARTESIVE Жыл бұрын

actually my chinese is quite fluent..

@auauseattle 2 жыл бұрын

How do you do the other side?

@ARTESIVE 2 жыл бұрын

Hi, what do you mean with "other side"? We show in this video the detail of full tensioning application..

@joandr3359 2 жыл бұрын

Can i remove film like this from MDF furniture? Or else can i paint over it?

@ARTESIVE 2 жыл бұрын

Hello, normally on our adhesive films is possible to paint over, to remove that is easier using an heat gun or hairdryer.. warm air helps the detach.

@joandr3359 2 жыл бұрын

@@ARTESIVE Thank you!

@yourdaddy381 2 жыл бұрын

What is the thickness of the vinyl paper?

@ARTESIVE 2 жыл бұрын

Hi "my Daddy" , thickness is about 220 microns.

@EbenezerTetteh-tl4yh Жыл бұрын

God reaching bless you ❤

@ARTESIVE 5 ай бұрын

Thank you!

@noteprom8171 3 жыл бұрын

It's really help me!

@ARTESIVE 3 жыл бұрын

thank you! we are really happy about it.

@leonida6024 2 жыл бұрын

Can I use a hair dryer instead?

@ARTESIVE 2 жыл бұрын

hi, of course yes!

@Sunny_uz 2 жыл бұрын

what's the film name and where can I find it ?

@ARTESIVE Жыл бұрын

A R T E S I V E all available on artesive.com

@kannancv 2 жыл бұрын

Ente ponnu sire , veedu evida , table kondu varatte !

@jaby1336 3 жыл бұрын

Can we use blower here

@laurasayuriamzah1785 3 жыл бұрын

@jaby1336 3 жыл бұрын

@@laurasayuriamzah1785 Yes, we can. I was able to do it using blower. 😊

@laurasayuriamzah1785 3 жыл бұрын

@@jaby1336 thank you so much!

@oneandxero 2 жыл бұрын

JARVIS what are you doing here ? 🤔

@danielwilde9601 10 ай бұрын

Found it useful till you didn’t show the next step of applying the back

@ARTESIVE 5 ай бұрын

Hi, maybe we'll show it in the next tutorial

@ranjanapant9084 3 жыл бұрын

you can go to 3:42

@angturil 3 жыл бұрын

Same voice as controllertech lol

@jco997 Жыл бұрын

I still see large bubbles on it. 👎🏿

@ARTESIVE Жыл бұрын

ok, where exactly?

@cheshirebowman4465 11 ай бұрын

Great visual video with a diabolical robot voice that just ruins it all. I turned it off.

@ARTESIVE 9 ай бұрын

that's the future.. AI.. sorry for the voice..

@cheshirebowman4465 9 ай бұрын

@@ARTESIVE 🐑🐑🐑🐑🐑🐑🐑🐑🐑

@ARTESIVE 9 ай бұрын

was a test.. we will do better in future.. @@cheshirebowman4465

@isabeldiago7071 3 жыл бұрын

It is not useful my. Table its attached to the wall to work easily on the whole other extreme that is cuved

@megamorphe 2 жыл бұрын

"Spatula" 🤣 couldn't finish the video because of this stupid automated voice you here on all low quality content.

@ARTESIVE 2 жыл бұрын

hi there, beside the voice over, is this video helpful for you?