Artillery Genius Pro - the new TPU 3D printing champion in my collection

Рет қаралды 19,351

Күн бұрын

Genius Pro by Artillery is the new TPU printing champion in my 3D printing collection (between 15 different 3D printers). Main reason is the Titan direct drive extruder. In this video I was able to 3D print Benchy using the same gcode prepared for PLA (only raised the temperatures and reduced fan speed). Another specification is that this is also the quietest printer between all my machines. Artillery is listening for feedbacks and several improvements are visible on this printer, compared to previous generation. In this video you can see the unboxing, assembling and 3D printing (PLA and TPU).
Aliexpress store link: www.aliexpress.com/store/4697033
Artillery 3d official website: www.artillery3d.com/
If you like my work, you could support me, more details on www.mytechfun.com/donation
Artillery Sidewinder X1 V4 video: • It's big: Artillery Si...
Contents:
0:00 Introduction
00:43 Specifications
3:31 Unboxing
5:48 Electronics inside
7:24 Assembling
13:24 Turning ON
14:48 Thermal camera view
16:10 Bed leveling
18:34 Small fixes
18:55 First 3D printing
21:10 Filament runout sensor
22:36 Analyzing 1st print
23:25 Own sliced cube
24:07 Add Genius Pro to Cura
24:48 3D printing Benchy
26:48 3D printing TPU
29:05 TPU Benchy
31:44 Conclusions
#artillery3d #geniuspro #3dprinter

Пікірлер: 67

@MyTechFun 2 жыл бұрын

Few comments asked to test thermal runaway protection too. I tested it, it has this protection, you can see the short video here: fb.watch/7QVQ-LewtP/

@peterboy209 2 жыл бұрын

I appreciate your content and that you don't "downgrade" your videos by annoying background music. Well done Igor👍

@nowinowi9232 2 жыл бұрын

This is by far the best review about this printer I found.

@Akres88 2 жыл бұрын

I am searching for a quiet small 3D printer and I can say that your videos are the one of the best. You show raw footage and your review is precise. I hate these videos, when they only show their own face rambling and fast forwarding with music instead of printer sound.

@gmergulhao 2 жыл бұрын

after modding an E3v2 for 9 months I can say: the insides of the genius pro are very user friendly! Seens to have stock fixes for almost every downside of a e3v2

@copternutFPV 2 жыл бұрын

I'm pretty new to 3D printing and have been absorbing a huge amount of your videos. You're very clearly and honest in your reviews and technical advice, l love my Ender 3 V2 and get reasonable results with TPU, that's the main filament l use (for drone parts) but also use P L A and PETG. You have 100% sold me on this printer, it will definitely be my next purchase when l add my next printer. Thank you very much for the excellent content you provide to us, greetings from Australia!

@yiarkungfu 2 жыл бұрын

Exceptional review and a great demonstration of each step in the process. I'm getting one for Christmas and now I know what to expect and the basics of how it functions. Thanks for going the extra mile, you rock.

@AzRAELGoDlIkE 2 жыл бұрын

Appreciate your work and watch most of your videos. This Printer seems really good!

@peanutismint 2 жыл бұрын

Thank you for posting this video! I just ordered one of these and there’s hardly any videos on them on KZfaq (especially not in English) so thank you for making one! It was very helpful.

@STIZZYMcNASTCHANNEL 2 жыл бұрын

Mines is arriving today. I'm pretty excited

@avejst 2 жыл бұрын

Great points Great Video👍👍 Thanks for sharing your experiences to all of us :-)

@thelightspeed3d712 2 жыл бұрын

Great job Igor

@kelben 2 жыл бұрын

Buterfly knife to open the box of the printer... thats gangsta.

@FRIDAY-SIX 2 жыл бұрын

Thank u bro

@Taki7o7 2 жыл бұрын

There are many reasons why you should ABL with every print tho ^^

@marianososa4309 7 ай бұрын

Excellent video as always!! I have an Artillery Genius (the first version), and I haven't used it for printing tpu because I fear that I might break the glass for excesive adhesion. Did you find any problems with this? Do you have any recommendation?? Thanks a lot for your help in advance!

@joseico90 2 жыл бұрын

By now I have run several Genius V1's for about seven months of 24h/7 work with no problems, they are very reliable and easy and quick to work with, they require only minimum maintenance, mostly just cleaning- and a nozzle change. Way better than my Ender 3 pro.

@MyTechFun 2 жыл бұрын

I have only SW X1, I had some small issues with it, but most of them are eliminated now (on both X2 and Genius Pro). Only I am not happy that extruder don't have more improvements, too plasticy, hard to set the tension etc.

@joseico90 2 жыл бұрын

@@MyTechFun I have had zero issues with these extruders, even though they are plasticky. I did put thermal paste of the heatsinks and alu tape at the bottom of them so the fan doesn't blow downwards. They just work..and I use cleaning filament when needed, no problems at all and I run them pretty much 24/7.

@dominikposchl8316 2 жыл бұрын

Can you show the mount of the BL Touch in greater detail? The placement is very close to the nozzle. I think there might be a way to use the spot for Sidewinder X1 retrofit

@r4v3ncl4w 2 жыл бұрын

Short question: In the Cura settings you didn't change the Start G-code. Maybe i'm confusing something but i think i read somewhere that you are supposed to add M420 S1 so that the printer uses the saved EProm Settings? Or did am i misremembering something or did i misunderstood it?

@3dprintingchannels472 2 жыл бұрын

I wish I got this instead of my ender 3V2, it's much more complete. So far I've had to add ferrules to high amperage cables (this has them already), yellow springs, CR touch, BTT smart filament sensor, Dual Z without belt, all metal extruder and capricorn tubing but still thinking about converting it to direct drive, Jyers firmware to get it all working..... I think overalls it cost me more haha. The speed of the motors seem lot faster too, the Z axis is like 3X the speed of the Ender V2

@OnlyTiramisu 2 жыл бұрын

Hey, great thorough video! I'm just starting out with 3D printing with my Genius (not Pro). I liked the thermal imagining, I will not be printing in the center now, thanks. Do you mind sharing your slicer settings as I am having a lot more stringing with my benchy?

@MyTechFun 2 жыл бұрын

I just used default settings in Cura (as presented in the video) and generic PLA for the material.

@PBENCE94 2 жыл бұрын

Hi! What cura profile did you use for the filamentum 98a tpu? I use the same printer, same filament, even the same color and I can't get it to stick to the bed at any temperature (tried up to 115c...) Thank you!

@MyTechFun 2 жыл бұрын

No, 115C is too much. 50-60C is enough, make sure that ved is clean (soap or window, glass cleaner). 230-240C for filament. Retraction minimal.

@TommiHonkonen 2 жыл бұрын

that z axis speed seemed fast

@ShebanFPV 2 жыл бұрын

Thank you for the great review! I think this will be my next (1st) printer for the TPU )) is there a way to upgrade nozzle cooling in order to avoid those seams on the other side?

@MyTechFun 2 жыл бұрын

I think better cooling will not reduce seams (better cooling is good for overhang and less stringing). But I noticed that I have smaller seams when I use PrusaSlicer. This means it is possible, only Cura needs a lot of more experimenting..

@ShebanFPV 2 жыл бұрын

@@MyTechFun thank you for the answer! Is there a printer which can do perfect TPU prints in your opinion?

@MyTechFun 2 жыл бұрын

@@ShebanFPV In my collection this one is the best for TPU (out of 15 different printers)

@ShebanFPV 2 жыл бұрын

@@MyTechFun thanks! Love your informative videos!

@justingortner6338 2 жыл бұрын

What is the material of the white boat (which printer better) vs. the tan boat (which printed with mistakes)?

@MyTechFun 2 жыл бұрын

White: PLA, tan: TPU (flexible filament)

@illogicalferi 2 жыл бұрын

As a mechanical engineer i have some bad feelings about the belt system and the 2 stepper motor at the same time. Won't it overconstrain the whole system ?

@thelightspeed3d712 2 жыл бұрын

As a backyard engineer... no. All it does is ensure the Z axis' stay in alignment. They are not needed in most cases but are there for the people that are new. This only has 1 driver for both motors. So its important they stay together. But the leadscrews are decoupled from the axis so it isn't constrained anyway

@WaschyNumber1 2 жыл бұрын

🖖 👍

@williamtabare8376 Жыл бұрын

Congratulations for the well-detailed videos... I wanted to ask you, in your opinion, artillery genius pro or sovol sv07 is better?

@MyTechFun Жыл бұрын

Genius Pro if you don't need too big speed and printer is in your office. Because Genius Pro is the quietest printer I ever tested. If you don't mind the noise and you need speed, then SV07.

@williamtabare8376 Жыл бұрын

@@MyTechFun Thanks... And what speed are we talking about... What's the difference? And a lot?

@MyTechFun Жыл бұрын

@@williamtabare8376 on smaller parts 2-3x bigger speed.

@williamtabare8376 Жыл бұрын

@@MyTechFun Ok thank you... Listen instead if I would like to put a glass plate on the sovol sv07 can I? Is the magnetic sensor capable of reading through glass?

@hapskie 2 жыл бұрын

Does it really have a BLTouch as you say, or is it a clone? Other thing is that I learned the carriage wheels are not supposed to be so tight you cannot turn them by hand. If they are, you will get a lot of wear very fast. My advise would be to set them so you could just barely rotate them with your fingers while holding the carriage.

@MyTechFun 2 жыл бұрын

It is not BL Touch as a brand, but bed leveling Touch as a sensor.

@superelpo87 2 жыл бұрын

compared to a cr-10 or a cr 6 if it is better? mainly pla mold

@MyTechFun 2 жыл бұрын

Maybe in this order CR-10, Genius Pro, CR-6 (best). But it also depend, how big printing volume you need.

@GiorgosLysigakis 2 жыл бұрын

TPU is a challenge. I would love to print cell phone cases with TPU.You think this printer can handle the task?Great video.Thanks!

@MyTechFun 2 жыл бұрын

Yes, I already printed tome phone case on Artillery Sidewinder X1, and Genius Pro is better (smaller area+ABL easier to get perfect first layer)

@GiorgosLysigakis 2 жыл бұрын

@@MyTechFun thanks for your response.For personal use or for sell? Thanks

@MyTechFun 2 жыл бұрын

@@GiorgosLysigakis for personal use (for my daughters)

@GiorgosLysigakis 2 жыл бұрын

@@MyTechFun do you think it can deliver professional results fro selling them?Thanks

@MyTechFun 2 жыл бұрын

@@GiorgosLysigakis Injection molded are much better, but with 3D printed you can customise them (some personal logo or text ect.)

@matheokoning4456 2 жыл бұрын

This printer seems promising. Shame about the heated bed. If that had been good, I would have bought this printer.

@MyTechFun 2 жыл бұрын

I completely agree with you. Same problem was with SW X1.

@dan2304k 2 жыл бұрын

Test for thermal runaway protection please.

@MyTechFun 2 жыл бұрын

Tested. It has thermal runaway protection. I recorded the testing process, you can see it here: fb.watch/7QVQ-LewtP/

@darkwhite1259 2 жыл бұрын

will you review the anycubic vyper?

@MyTechFun 2 жыл бұрын

Probably not, nobody contacted me from Anycubic so far.

@darkwhite1259 2 жыл бұрын

@@MyTechFun oh i see

@user-ku8yr2fw5j 2 жыл бұрын

Ez a videó elérhető magyarul is? Értek angolul, de azért nem az igazi.

@MyTechFun 2 жыл бұрын

Sajnos nem, csak angolul.

@user-ku8yr2fw5j 2 жыл бұрын

@@MyTechFun Köszi! A videó nagyon jó. Genius pro-t rendeltem azért vadászom a róla szóló videókat.

@randomname3894 2 жыл бұрын

I can’t believe they put the same plastic Idler-arm on the extruder again.. the aluminium version is dead cheap, because so many people bought it after the plastic one is broken. I had a lot trouble with the genius and still have.. the extruder gear is slipping so easy on petg, that I need to print slower than normal, so the volcano hotend is pretty much useless. I also rewired the whole machine after the first flat cable connector gave up. There are tons of videos about inconsistent layers on the sidewinder and genius ..sometimes it’s the extruder, sometimes the top belt, sometimes the motor alignment. Good luck:)

@tomsenq 2 жыл бұрын

there are also tons of Videos of Sidewinder/Genius Printers that are working fine. What now? And usually People are happy with there Maschine don't post on the Web.

@randomname3894 2 жыл бұрын

@@tomsenq My experience was not good, so what now? I'm not allowed to write about it? If a company is doing an update on a machine, is it not okay to wonder, why they didn't address an issues a lot people had with it, specially when it's a three dollar part? I can write a full article of what's not so good with this printer, but it's cheap, so I can understand that some parts are not perfect.