Great video, Thank you very much. This is just what I needed after upgrading to an all metal hot end in my X2.

Great video. It has been a while since I have done this and this video makes a great refresher.

Great video, thanks for the good explanation. Thanks to you my Sidewinder X2 is running again.

Thanks for the video! I tried your Marlin build for the SWX2 (since it seems to be the only one supporting the new TFT) and it works great for the most part. It's just that sometimes it crashes when I turn the printer on or take out the USB stick to put some files on it. A reset helps. It has never crashed during printing so far.

Guida perfetta, ho seguito le istruzioni ed è stato facilissimo installare il firmware. Grazie, grazie e grazie!!! 😉

Thanks for the tutorial. I've had my X2 since the beginning when they were $460. I still think it's a great deal and a great printer. I would like to upgrade it a bit but not too much (I'm a great believer in the Engineers mantra, "The enemy of good is perfect"). For me designing things in CAD is the hobby. I tend to produce useful things (a lot of brackets, mounts and adapters) rather than knick-knacks. I've pretty much worn out the surface of the glass bed and now I'm using a Garolite sheet clipped over it that works pretty good. The Garolite sheet also seems to deal with the four mounting cold spots pretty well although gluesticks are part of my life now. I'd like to upgrade the firmware if it makes it better but I don't want to disturb it too much. I run it via Octoprint with a RPi3 integrated into the printer. After the Ender 3 it's nice having a printer that I can rely on. I wanted to switch to an all metal hot end so I bought a spare print head on Amazon and all the bits to upgrade it. Thanks for the video highlighting all the things I did sub-optimally. I've corrected the errors and I'm looking forward to running the new head and refurbing my original. Needless to say, I subscribed and I'll be binge watching all your video's now. Possible experiments in Klipper will be reserved for my old Anycubic Linear Plus Kossel.

great video, thanks!

Nice mate , as always. Ill hope you do also the x1 , as it is more complicated with the lcd

In the description section, please update the link */pages/downloads* with */pages/d*

Thanks for the tutorial. The upgrade went pretty well, but I do have a weird new behavior. If a print is paused, when I restart the print, the printer retracts a large amount quickly. This always causes a clog. Is this a known issue? Is there a newer firmware update? Thanks in advance!

Regarding the TFT. I used the X2 firmware from your site and everything looks good functionality wise however I'm using Digant FW and TFT FW for the Waggster Mod on the X1 and I like the TFT screen of Digant's setup better and remove the "Ethreal" logo on boot up (no offense). I'd like to get the TFT firmware from Digant on my X2 for continuity sake between my X1 and X2. However loading Digant's TFT files on the sd and start up doesn't allow updating the TFT with your compiled fw. On startup it just boots right to Ethreal logo and subsequent menu and ignores the sd card and files. I thought maybe I could just load his bmp images in your TFT files but I don't see any bmp files with your TFT setup. Can I use other TFT setup with your mainboard FW or am I locked into using only your stuff?

thank you for the video(s). I am new to all this stuff, how do i know wether i have the ruby mainboard? I bought my x2 a few weeks ago and though i think it is equipped with the new tft. I`d like to update/upgrade the firmwares but am a bit frightened to brick my device....

Hi Thankyou for the tutorial, when I get to the stage using the stm32 programmer it's not detecting the USB dfu, pronterface is doing what it should what am I doing wrong? Cheers

Have you got a link for the stl files for the two blue frame supports you have attached to your z moters please

Are some functions added too? Like linear advance and arc welder? Thank you Artillery Guru :D

Good evening, I know the topic is: intaller firmware on Artillery. Do you think you will ever switch your Artillery SWX1 to Klipper with a Raspberry? I have been looking for a few days if this has already been done. Thanks for your videos very good work.

Hi there, Need help. Just tried to update Marlin firmware from freakydude from GitHub update via pronterface and stm35. After I download firmware via stm32 and install to printer, then reset it, and was great but I didn’t save my Z offset and Extrusion data before… so I tried to go a step back and install old backup firmware I made via stm32. So I connected printer via usb cable to pronterface, than stm32 and install backup firmware as the pdf instruction said. then reset printer and… I tried to connect with pronterface to reset eprom and… protnerface can’t see printer via usb cable… also any tryouts to axis movement, heat extruded or bed, any function via touch screen on printer asp doesn’t work. Looks like everything failed… how can I put into printer firmware again when pc don’t see it via cable ? Help please :(

Great video!! I can't tell you how many people get mad because you can't just load this firmware on an SD card. Now we have a nice easy tutorial to follow. Thanks!!!

Thank you very much!

תודה!

Great Video. Do You by any chance have the Firmware for this. having issues with the one out of the website.

Hi there. Thanks for your helpful content. I'm trying to revert from klipper and reinstall sidewinder x2 firmware. When trying to get into dfu mode with pronterface I get "rubbish reply from COM5 at baudrate 115200". Any tips?

Thanks for your video. My screen went black, not from your video. In another video. Is there a way to get it to come on again?

Update to my latest regarding the hex file not being created. For whateverb reason the X2 firmware from your site has some file embedded or an error somwhere that no matter howe many times I follow your process here the hex is not being created. However, when I get the FW from Artillery's site and run through the process the hex file is created.

Artillery Downloads page is not functioning. Error 404

Have you tried input shaping on the latest Marlin?

how can i eneble manual leveling artillery sidewinder x2 firmware? - I have downloaded files but what next?

Hi man, any ETA on the video about the inductive endstop? :)

Hi I recently go a used sidewinder X1 I see it's hard the bottom panel removed, my problem is that the LED will not work,i put a new one in still not lighting up. Do you have a diagram for the wiring pin out for the LED as I can't find it on the website.???

I get mismatch data when i try to push the firmware to the machine through stm32, how do i overcome this issue? Its with the stock firmware or the klipper firmware

Thanks. This' been super helpful I'd like to point that in case it happens to someone like it happened to me: Make sure ALL the folders along the root where saved the source code (say, some other folder instead of the desktop as shown here) DO NOT contain spaces in their name. VScode/PlatformIO will fail to compile. I'm curious has to how to flash a .bin file thou since it's the file provided by Artillery if you don't compile it yourself

Is there any solution to prints not resuming after a filament runout is detected? I can swap filament in and resume and the printer head moves like you'd expect but the extruder stops extruding. I basically waste a crap load of filament if I think the spool won't make it to the end fearing a long print will ultimately fail because a filament swap won't resume correctly.

Thank you!

This does not work on my AS-X2 and/or my replacement motherboard. There is a hardware jumper that must be placed on the motherboard before it will accept new firmware. This may not be required on all the motherboards out there, not sure. Good luck and good printing. BTW AS-X2 has significantly improved performance with Klipper if one is inclined to change the firmware.

Hello! a few days ago i downloaded klipper to my artillery hornet, after i flashed it on with octoklipper the screen went black and although i can connect it through usb when i use pronterface the baudrate isn't right. i used your klipper firmware.bin settings thanks in advance! P.S it shows this (Got rubbish reply from COM7 at baudrate 250000:Maybe a bad baudrate?) problem in pronterface, hope it helps!

Great video. Thank you for help. How do I know I my X2 has RUBY motherboard?

I have error when visual program startup from file location. that says 1 error, 0 sucssed

Great video ! Thank you very much for your time! Could you please help me to download the file ''Artillery Sidewinder X2 Firmware (Source)''. It is my last file i have to download and i can;t finf the right file from the artilery site. Thank you in advance!

My stm32cubeprogrammer says sector 0001 doesnt exist, and doesnt install the firmware. Pronterface dont connect to the printer, so i had to use the jumper method. Any suggestions?

my stm32 software looks different and doesn't offer me the option to choose usb and connect

I've made this update. The stepper motors now are noisy. How I can rollback to the previous version?

I'm new to this... I've downloaded all the software and followed all the instructions. Now granted, I'm using a MacBook Pro, when I load the X2 software into Platform IO IDE it doesn't give me the option to "Add" the programs... now what? I'm stuck and don't know what to do next... HELP!

How to do it with the X1?

Hi, i tried to put my x2 into dfu mode, but i had a lot of errors. i heard there is a way to put it in dfu mode with a jumper. Is this true, and could you help

Are there any known bug issues with the X2 firmware from your site?

Hi, after it says "printer is now online", when I write the m997 command, it says instantly "Can´t write to printer". I´ve also tried to set the jumper on the mainboard, but it did not work. Has the flash been succesfull, if I turn on the the printer and the display is black? Because my display does not change at all after I´ve followed your steps..

Hi, so, I followed the many steps and processes, but how do I know if I was successful? My printer shows 3.2.6 still. Does STM32 give an error code if not successful? Thanks, -Frustrated

How do i know if my hornet has a ruby board or not?

thanks for the video.How can I work with a .hex file in visual studio? I want to use the file that artillery gives you to use manual leveling on my x2.

Thanks!

I have a question. Couldn't you upload the .hex file and skip all the beginning portions?

After updating firmware, ma printer is not working What should i do

Great video but the problem I have is when I download the file I can't open it. It is a HEX file that I can not open. Any suggestions?

Cant seem to connect STM32 so now i dont know what to do

You need to do a video for adding the bin files only.. actually from 2;44 onwards gives that information

What happens if the programing fails? Gets soft bricked?

I now did all this and the display does not communicate with the board anymore. Guys, maybe its important to upate the TFT along with the mainboard. I am waiting now for my sd card and reader i ordered to complete the mission. I wish i knew the option how to safe the current firmware on the printer. Now i am not able to print until delivery arrives. This tutorial is good, but far to imcomplete for beginners! You may end up like me with a non working printer.

👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏

Clank

bruh, wtf, all this just to update firmware?! Surely there is a faster way!

I have tried this a handful of times and after compiling I get a success however I am not getting a hex file created in the marlin source/pio/build/artillery_ruby

I got failed on compile in vscode. Any idea why? *** [.pio\build\ARTILLERY_RUBY\firmware.elf] Error 1 Environment Status Duration -------------- -------- ------------ ARTILLERY_RUBY FAILED 00:00:51.018

I'm trying to build it, but it gives me an error, perhaps they changed the source files since? *** [.pio\build\ARTILLERY_RUBY\firmware.elf] Error 1 ================================================================================================= [FAILED] Took 107.04 seconds ================================================================================================= Environment Status Duration -------------- -------- ------------ ARTILLERY_RUBY FAILED 00:01:47.038 ================================================