AtomRC Dolphin INAV AUTO LAUNCH SETTINGS & MORE, BLHELI ESC BRAKE SETTINS & MORE!

Рет қаралды 5,599

Күн бұрын

In this video I go over INAV Auto Launch settings and well as other INAV Settings. Also, how to setup the esc brake through BLHELI Software. ENJOY!
BLHeli Configurator - github.com/blheli-configurato...
Buy Your Dolphin Here - atomrc.com/?ref=yv0fs50u
Use this COUPON CODE to save $10 Off YOUR ORDER - JeffDoesThis
--------------------------------------------------------------------------------------------------------------------------------------------------------
INTRO - 0:00
INAV MIXER SETTINGS - 0:30
INAV OUPUTS SETTING - 1:35
STOP MOTORS ON LOW THROTTLE - 1:54
BLHELI SOFTWARE OVERVIEW- 3:13
BLHELI STOP MOTORS ON LOW THROTTLE, BRAKE ON STOP - 4:39
BLHELI MOTOR DIRECTION CHANGE - 5:01
BLHELI BEEP/BEACON STRENGTH - 6:17
INAV PORTS SETTINGS - 8:26
INAV CONFIGURATION SETTINGS - 8:42
INAV FAILSAFE SETTINGS - 9:38
INAV PID TUNING - 9:46
INAV ADVANCE TUNING !AUTOLAUNCH! - 10:14
INAV PROGRAMMING, ADJUSTMENTS, GPS - 15:34
INAV OSD MY LAYOUT - 15:46
AUTOLAUCH DEMO - 17:00
OUTRO - 18:15
--------------------------------------------------------------------------------------------------------------------------------------------------------
TIBERIUS CREEK RUN - ATOMRC DOLPHIN - • TIBERIUS CREEK RUN - A...
Let's go for a 3.5mi/5.6km cruise and test to see my MAX range.- • Let's go for a 3.5mi/5...
AtomRC Dolphin #2 - My New Setup - INAV SETTING, MODS & ACCESSORIES AND CENTER OF GRAVITY - • AtomRC Dolphin #2 - My...
AtomRC Dolphin 360 Video! - • AtomRC Dolphin 360 Video!
RC PLANE LED LIGHTS! HOW TO INSTALL AND WHAT YOU NEED! - • RC PLANE LED LIGHTS! ...
ATOMRC DOLPHIN PID TUNING! BETTER ANGLE MODE & LAUNCHES - BEGINNER FPV PILOTS - • ATOMRC DOLPHIN PID TUN...
ATOMRC DOLPHIN MOTOR MOUNT UPGRADE KIT - • ATOMRC DOLPHIN MOTOR M...
ATOMRC DOLPHIN - FLYING IN 30+MPH WIND! - • ATOMRC DOLPHIN - FLYIN...
AtomRC Dolphin INAV AUTO LAUNCH SETTINGS & MORE, BLHELI ESC BRAKE SETTINS & MORE! - • AtomRC Dolphin INAV AU...
AtomRC Dolphin Upgrades & 3D Printed Parts! DO THIS FIRST! - • AtomRC Dolphin Upgrade...
-------------------------------------------------------------------------------------------------------------------
MY ATOMRC DOLPHIN GEAR, PARTS, 3D PRINT LINKS AND MORE!
Plane
AtomRC Dolphin RTH Model - atomrc.com/collections/fixed-...
Battery
ZOHD Lionpack Max 21700 4S1P 5000mAh 14.8V Li-ion Battery - www.getfpv.com/zohd-lionpack-...
Video System
DJI O3 Air Unit - amzn.to/3rNBA3D
DJI FPV Goggles V2(Renewed) - amzn.to/46i2LCQ
Pan Servo - fpvdogfight.com/products/moti...
RC LINK
Transmitter - RadioMaster Boxer 2.4G Remote Control ELRS 4in1 - amzn.to/3LPDBDv
Receiver - RadioMaster RP3 ExpressLRS 2.4GHz ELRS Nano - amzn.to/3rG9FCJ
Receiver -BETAFPV SuperD ExpressLRS 2.4GHz V3.0 Diversity - amzn.to/3Q74God
3D Printing Links
AtomRC Dolphin - Motor Mount Upgrade Kit - www.thingiverse.com/thing:626...
Walksnail V2 VTX "Tray" for Dolphin - www.thingiverse.com/thing:624...
DJI O3 AirUnit 20mm and 25.5mm Mount - www.thingiverse.com/thing:584...
DJI O3 Lens Cover - www.thingiverse.com/thing:569...
AtomRC Dolphin v1.1 !DJI O3 mount & Scoop! - www.thingiverse.com/thing:590...
RC Hatch Latch - www.thingiverse.com/thing:362...
Atomrc Dolphin ESC cover (low drag + high airflow) - www.thingiverse.com/thing:514...
Atomrc Dolphin cubre servo - www.thingiverse.com/thing:542...
3D Filament Links
GIANTARM TPU 95A - amzn.to/3LKZq75
eSUN PLA+ - amzn.to/45lrbdp
MY Building Supplies
Creality Ender-3 S1 Pro 3D Printer - amzn.to/3ZHh7dw
Assortment,M2 - amzn.to/46kJ79e
Assortment,M3 - amzn.to/3ZHNnNu
20 Pieces 3-pin Servo Extension Cable - amzn.to/46CZMok
HJ Digital Servo Tester - amzn.to/3Mckd3N
300 PCS 3:1 Ratio Heat Shrink Tubing Kit - amzn.to/3RKv5cw
Hakko FX888D-23BY Digital Soldering Station - amzn.to/3F5ew3q
2.54mm Right Angle Male Header Pins - amzn.to/3LTafE3
4P Dupont Female to Female Harness - amzn.to/3LJWMyw
-----------------------------------------------------------------------------------------------------------------------
DISCLAIMERS:
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.

Пікірлер: 36

@danjensen9425 4 ай бұрын

Thanks just finished my dolphin.

@danjensen9425 8 ай бұрын

I’ll try the idle increase with my S800 tomorrow. Good video

@fly2me2day 4 ай бұрын

Lot of info there as new dolphin builder. Thanks for sharing the great 3D files.

@JeffDoesThis 4 ай бұрын

My pleasure!

@Synthetic11 3 ай бұрын

Thanks Jeff for all of your very helpful videos that help us out. I appreciate it.

@JeffDoesThis 3 ай бұрын

Your welcome! Enjoy your flying!

@ebikefe 9 ай бұрын

Thanks for sharing this. 👍

@JeffDoesThis 9 ай бұрын

You bet!

@YT-qp3xw 8 ай бұрын

Hello jeff...can we autolaunch the dolphin using frisbee/wing throw style? I already had my fingers clipped by the 7 inch props during launch...aauochhj

@Jetsect9 8 ай бұрын

Great vid! thanks for sharing.

@JeffDoesThis 8 ай бұрын

Thank you!

@Dashone93 8 ай бұрын

Do u have to put it in stability mode

@bushcraftmonkey7643 6 күн бұрын

Hi Jeff If BLHeli doesn’t show the low voltage cut off, does it mean there is no cutoff for that esc? And do you connect the BLheli configurator thru the FC usb plug? I used a BLHeli usb dongle directly to the esc, which is not so convenient 😅

@squirrelynutz1 3 ай бұрын

How are the control surfaces set? I just got a dolphin and the right side is slightly higher than the left in manual mode while level. Kinda new to fixed wing. I did succeed flying the penguin.

@illuminatorix 9 ай бұрын

Hey Jeff, thanks again for your videos! May I ask something? Let's say I have the matek board (the 405 like this one) and want to install it on a different plane, are these settings OK and need some adjustments, or it's very different and has to be set again from 0? Thanks!

@JeffDoesThis 9 ай бұрын

From one flying wing to another, you should be okay.

@anupmokashi3114 8 ай бұрын

Hello sir I know cg point is marking but how can balance CG properly like your atomrc dolphin? And can I copy your pdi tuning to get smooth flying sir?

@rrenegadoo 3 ай бұрын

Excellent video.... how do you set-up the channels for the pan and tilt in your radio and Inav?... I think I am doing something wrong thaks.

@JeffDoesThis 3 ай бұрын

I'm making a video right now on my setup and how to do it. It should upload on Thursday.

@JeffDoesThis 3 ай бұрын

What trouble are you having?

@emyeukhoahoc3906 5 ай бұрын

In autolaunch mode, we don't need to raise throttle, right? Then after throwing the plane, we will raise the throttle (to 50-70%), did I understand correctly? And do we set switch for autolaunch and angle mode are activated at the time?

@KillerWhale806 3 ай бұрын

arm in autolaunch, raise the thottle to max. the plane will throttle up to the autolaunch idle throttle you set, then you throw it. after it detects the throw it will raise throttle to the autolaunch throttle and climb out. after autolaunch has completed, or you touch the sticks then your sticks will start working normally.

@GeorgReitterer 7 ай бұрын

when i hit "read setup" in BLHELI it says "reading setup finished" but nothing is showing up, do you have any tips? ESC is powered with a battery

@JeffDoesThis 7 ай бұрын

What ESC is it, make model?

@YoungGhillie 3 ай бұрын

thanks for this config u have helped me setup my first fix wing, 2 questions though, what switches should i setup (flight mode, buzzer rth etc.) Also do you have the stock electronics on your plane like the 2306 motor and 30a esc from atomrc? Im asking as i want to copy it exactly so that i can have my plane working with the stock electronics. Thanks :)

@JeffDoesThis 3 ай бұрын

Yes, in this video, I have the stock electronics, motor, esc, and prop. I'm making a video right now on my radio setup, too. It should be out on Saturday or Sunday.

@YoungGhillie 3 ай бұрын

Thanks jeff, I'm hoping to maiden mine this weekend! Sadly it won't arm and no there are 0 satellites connecting to the gps@@JeffDoesThis

@JeffDoesThis 3 ай бұрын

Check this for the gps, 8:29 gps on uart 4, 8:49 GPS For nav and telemetry, 15:41 at the top GPS for navigation and telemetry. Then take it outside and wait a couple of minutes for it to get a lock. Once it has a lock and 6 satellites it remembers your general location and will lock satellites faster then next time you power it up. Let me know if this works.

@illuminatorix 9 ай бұрын

Thank you for this video, will help my problem of the auto lunch! its new and didnt know how to set the correct values! May I ask if this is the stock motor or you can set these values to every motor? I have a 1500kv motor, 7x4.5 prop and 6s battery, is it ok or the throttle will be too much? Thanks!!!

@JeffDoesThis 9 ай бұрын

Too much throttle is never a problem. You can also can apply these setting to other crafts and different motor/prop setups. When setting up autolaunch I start with max setting and then tune it down from there.

@illuminatorix 9 ай бұрын

@@JeffDoesThis I am building it right now and these settings are very valuable to me! Thank you for this!!!

@JeffDoesThis 9 ай бұрын

No problem!

@JeffDoesThis 9 ай бұрын

Also, check out this video - It has some updated inav settings in it for the PID Tuning - kzfaq.info/get/bejne/m-CEpttyzrKRaIk.html