I done it 4 years ago with out talking the DPF too.

you removed it from the top of the car or under the car

Thanks so much for watching

@@HugoCalisto hello where about you guys are from because I have Audi a5 of I ever need work my car

@@ahmadsayedgol4186 hi we are from Boston Lincolnshire

Thanks

Thank you

How did you get on? Both of mine are ceased so I’m debating taking it out with the rack in situ

@@gavmcp11GT that’s spooky same car back in the workshop today for a timing belt and water pump. Regarding the seized in steering rack bolts tried getting the box past the rack er no chance in the end we just went for it used a three quarter drive breaker bar which didn’t have any flex in it unlike an half inch bar anyway they came out but I have to say it was a bit worrying at the time. Let me know how you get on👍

@@kevinpalmer7452 ya joking I gather we are needing a ton of heat on them! It’s a rubbish set up

@@gavmcp11GT your right about using some heat it will help greatly. Other garages I’ve worked for in the past have had oxyacetylene gear it’s a must have really current garage boss tells me his insurance forbids the use of it so we don’t have it. I’ve taken it upon myself to purchase some map gas canisters and a torch the same as plumbers use while not as hot or versatile as the oxyacetylene set up I’m quite pleased with it.

@@kevinpalmer7452 just snapped a rack bolt 😬 looks like the subframe is coming off now

Thanks is a big job you will appreciate after is than

Can you subscribe please will help tha channel

Did you watch the video the whole thing was a headache 🤣

Yap I'm Lake my is 2012...2013 if you want can you subscribe 😉pls

Hi bro you need to see when you driving 40mph press gas full down if the Rpm going up and down like losing power.. if yes you have a sleeping clutch .

Thanks so much for watching

That is the best tink to do is do all in one's

Hi wen you change have you you change all set flywheel. Clutch disc. Pressure plate. And. release bearing

@@HugoCalisto It was a solid flywheel so that wasn't changed the kit came with pressure plate, disc and release bearing.

@@jerryrawlings8885 okay I will ask my brother what he thinks about and I will let you know

Did you use the clutch with the correct springs rated for a solid flywheel? if they mismatch you will get chatter but the vehicle will run fine.

@@adivarso8175 Thanks.

Hi yes you have to remove the starter motor..

Well I didn't have to

No, you don't since the cylinder has been dismantled just from the gearbox without touching its own oil line supply.

Yes is 3 bolts but I did think they were missing but not I have just make te tha first time 😂

Hi it was 65000 miles

Ola el cambio cuesta en uk 🇬🇧 se fores tou a fazer mas o minos 550£

Hi my flywheel cost £480 to £530 if you done your self if not £680 to800

Hi it takes 10h job

Hi probably is the gear box transmission issue ..or the gearbox selector mechanism

Manual 8)

@@HugoCalisto a ok ;)

Hi no my is manual

Hi Tristan my is manual ..if your revs going up and dawn when you press on a gas than yes can be the clutch

Tristan if you have time see these video on start da video you can see revs going up and after Stoke for few seconds and go again ✌ kzfaq.info/get/bejne/ZseKrK-J3L-bfJ8.html

Hi is very difficult access but you will be able to turn the crank from the bottom with ratchet tool but you not gonna have much space there.i did that on this way

Sachs flywheel kit

@@HugoCalisto tankyou

Se fores tu a fazer fica mais barato mais ou menos 600£ mas se fores fazer uma garagem pode ir ate as 900£ ou 1200 depende do sitio

@@HugoCalisto obrigado all the best take care I’m from Leicester abraço