Audi A5 Convertible written off for a detached rear Glass?

Рет қаралды 59,629

WRITE-OFF RESCUE

4 жыл бұрын

DIY repair on a 2011 Audi A5 convertible / cabriolet rear window. Fix it yourself with our help for $20!

Пікірлер: 47

@beachmotosportsbeachmotors9500 2 жыл бұрын

these tops should be a recall. Ive never seen one that lasted.

@stunnamrsports Жыл бұрын

EXCELLENT job. Ridiculous for companies wanting to charge thousands for this SIMPLE repair. I think u can start your own business doing this. So many ppl have this issue. Thanks for sharing 👍🏻

@open2yourmind Жыл бұрын

Excellent job - worked for my A4 / 2004 as well. I probably saved me a CHF 6500 Bill. The "Bostik Simson ISR 70-08" is THE ONLY and reliably working solution - I have tried more than two other glues - Bostik works.

@clonkex 3 жыл бұрын

Gonna try this on my '09 A3. Certainly worth a go before going all-in for a new top!

@olen2808 4 ай бұрын

Perfect, Good Job.

@fl2o74 2 жыл бұрын

Good job

@williampeck7879 Жыл бұрын

I used black gasket sealer and it worked perfectly.

@MrOffshore 2 жыл бұрын

I used 3M Window Weld and their suggested primer. Followed directions exactly and the repair lasted a little over a year. Not happy with it coming apart, will need to do it again. I’m going to pull the canvas down a bit on the bottom where I had my failure this time to take some pressure off the bond. Hoping that will help as the convertible top material has likely shrunk a bit.

@ismarttaxes7524 21 күн бұрын

Mine has a direct texas sunlight on the back window. It heats up so hot that it will burn me. I think that will make any type of sealant last less time. Silicone would be difficult for it to penetrate though. But I don't know how realistic it would be for me to add a layer of silicone or rubber around the glue 😅

@billymillz1367 Жыл бұрын

You need the suction cup clamps &3m marine sealant clear. That works best

@misukkk 3 жыл бұрын

Verry good job!

@write-offrescue4641 3 жыл бұрын

Thanks!

@tostitos2890 Жыл бұрын

my '09 a4 has a simmilar problem except the top has shrunk at the top and nothign we have done has moved it or the window into place to apply glue, is there any other method we can use besides replacing the top?

@TheNicoderechte 10 ай бұрын

I used a water proof seal glue und it worked for my 2002 a4. Only costed 6€ and saved me a 2000€ bill for a new roof

@chrispatrick1351 2 жыл бұрын

Excellent, great help

@jonmack6476 3 жыл бұрын

How did it come out

@karryrowe2561 3 жыл бұрын

I have a Toyota Celica GT convertible. 1997, beautiful red, hardly any miles. The rear window has completely fallen thru. I wonder if this would work? The window has rear defrost so I guess that’s probably just finished but I would like to get the window back in.

@write-offrescue4641 3 жыл бұрын

Should work on any car. Might be trickier if the rear window is not glass like the Audi. If the wire to the rear window is not broken your defrost should still work. Good luck!

@jdfagen Жыл бұрын

Great professional job attaching the window. I am unfamiliar with what written off means. Does that mean you purchased the car at a considerable discount? Worst case scenario with this fine car is that you would just need a new convertible top. Am I correct or is there more to this? Would like to hear your views.

@write-offrescue4641 Жыл бұрын

Written of means insurance paid out the owner because they didn't want to fix it

@Sancredo Жыл бұрын

Great video! Two years in, does it still hold on? Thanks in advance!

@write-offrescue4641 Жыл бұрын

I sold the car soon after so can't say for sure. I did have at least a year on my personal car after doing this and it held fine

@vesalahmadi5764 2 жыл бұрын

Could you please send a link to Bostik products? I’m in USA and Seems like bostik is not available in US Market

@write-offrescue4641 2 жыл бұрын

If you can't find bostik, just make sure you use a product designed to seal in windscreens

@christophermagnan4792 3 жыл бұрын

Hello. I have the same problem with my beloved S5. Unfortunately, the fabric on lower right hand corner sags, which pulls on the glass’s upper right hand corner. Do you have any suggestions to restrict the fabric from sagging. I can send pictures.

@christophermagnan4792 3 жыл бұрын

Looks like a bolt snapped in the frame and that is causing the sag on the right hand side.

@write-offrescue4641 3 жыл бұрын

Make sure the glass has good attachment to the outer canvas roof and the inner material 'head liner' should come with it.... good luck

@MrOffshore 2 жыл бұрын

My A5 had a broken cable that allowed it to sag. There’s a small parts kit from Audi that has cables for each side, it was a little over $200(US)…pretty expensive for what you get. Easy to replace though. But because it sagged my glass pulled away and that was a bigger repair, like you’re seeing in this video. I used 3M Window Weld along with the recommended primer and followed the direction exactly. It’s messy stuff, mask off and wear gloves like this video shows. But I did not put the glue all the way out and use it as a caulk, I don’t like that look…it held for a year and pulled loose at the bottom (that’s where I am today and not happy). I also used window clamps to hold the canvas top to the glass while it cured. I’ve seen people use 3M VHB tape with success, though this video said they had failures from water…VHB should not fail from water, we build car trailers that have VHB as the bond to hold the aluminum skin on, and water can get to the tapes edge…no failures. I’m thinking he may not have primed window and canvas top possibly or had a contaminated surface. I’d love to try the VHB, but I will likely try the 3M Window Weld again. I might try not to put the canvas back in the factory position and pull it back down a bit because the canvas has likely shrunk and was putting too much constant pressure on the bond causing the failure. I hate doing this job. Good luck to you.

@christophermagnan4792 2 жыл бұрын

Thank you. The repair is adequate. My car is 10+ years old. It still runs and has less than 100k miles on it.

@my59ranch 2 ай бұрын

How long did you keep the car? How was the seal after some time? Thanks!

@write-offrescue4641 2 күн бұрын

I expect you may need to touch some part of the rear glass up once a year or so if you don't reseal the whole thing. Not that much work or cost to save thousands on a full replacement

@pigpigxx 3 жыл бұрын

Oh, my AUDI TT mk2 has the same case as your A5. How's your case update, is the glue still last ? I want to follow your video to try myself, but my garage don't have the ceiling like yours to mount the tape and suction cup. Any other way I can hold it for an hour ?? thanks for the share ☺️

@write-offrescue4641 3 жыл бұрын

Just get some pressure on the inside of the car pushing the window out and it should do the same job. Otherwise you could always tie it to a tree or your house gutter and pull from the outside like me. Repair should last at least a few years or more under normal conditions. You can always clean it up and redo it again too if it fails. Just take your time to do a neat job. Good luck

@pigpigxx 3 жыл бұрын

@@write-offrescue4641 the top, left, right of the rear window is already unglued. But the bottom is still fine. You suggest to take it all off to glue it or just do the top, left, right is fine ? My TT is a 07 mk2. Btw, Im also comparing the 3M 08609 Window-Weld Super Fast Urethane Black vs the bostik 70-08 which you using... Any idea ?

@write-offrescue4641 3 жыл бұрын

Probably not much difference between the materials. I would just glue what has separated as the other side will hopefully stay stuck. They only come apart because the canvas shrinks over time. Once the pressure is removed by the other sides the rest might be ok in the long term. You can always fix it again if that comes off later. Good luck

@georgescortia3798 3 жыл бұрын

I used liquid nails clear waterproof tube from home depot which cost around $8.00. My 05 Audi conv. I didn't clean anything and it is really tight.

@ksw4tq1 2 жыл бұрын

How long ago, and is it still attached?

@georgescortia3798 2 жыл бұрын

@@ksw4tq1 It is still attached. No problems with it.

@benwaybenway3242 Жыл бұрын

@@georgescortia3798 still attached?

@georgescortia3798 Жыл бұрын

@@benwaybenway3242 Yes it is still very tight. I had to add a bit of liquid nails where it was leaking a bit. Now no leaks at all.

@tonytran9337 2 жыл бұрын

Took me a day to replace the top

@cdanerg9416 Жыл бұрын

If you don’t have all this stuff, will an Autobody shop be there right place to go.

@pigpigxx 3 жыл бұрын

HV just got the bostik 70-08ap, just when I look into the instruction, it say prepare the surface with primer. But what description say the SMP material don't need any primer. Confuse now do I need to use the primer ? If yes, put on both glass and canvas side ? Or just glass side ? p.s. I cannot get Bostik N40 primer in my region. Only I can get is 3M Primer 94primer... Can I use this with Bostik 70-08 ?? Mind is a Audi TT roadster convertible

@write-offrescue4641 3 жыл бұрын

I don't know the specs on that Bostic material, but if you clean it with alcohol or metholated spirits it should clean the surface enough for a good grip. Unless your canvas is really dirty I would just use it on the glass.