Autoextrude Mk3 Supra replacement spoiler brackets

Autoextrude Mk3 Supra replacement spoiler brackets | review and install

Рет қаралды 256

Ай бұрын

Hey guys today's video was for the review and install on the Autoextrude replacement spoiler brackets. This is a great replacement for the old factory brackets that break just by looking at them the wrong way. These little brackets are pretty robust and will definitely get the job done. Worried your spoiler will come flying off on the freeway?? well worry no more! Huge shoutout to Autoextrude for the hookup! Go check them out!
autoextrude.com
- Spoiler brackets -
autoextrude.com/products/mk3-...

Пікірлер: 16

@brandontucker6069 Ай бұрын

glad to see you still making content brother

@mainstreambuilds Ай бұрын

Haha yeah. Life just gets busy sometimes! Hopefully more to come very soon.

@scorpjmateo8766 Ай бұрын

Looking forward to a new full in depth 7MGE video! You convinced me to keep mine 7M, you do great work!

@mainstreambuilds Ай бұрын

Thank you so much! I will definitely do an updated video! Just added it to my list.

@Specer_G 11 күн бұрын

Thank you for this guide! I just picked up a mk3 Supra with a three piece wing not connected, but I didn’t know what fittings I needed for it! Side question as I’ve watched a few of your videos and noticed you don’t have a charcoal canister. Did you keep the charcoal canister for the gas vent line? Did you reroute the vent lines somewhere else? Or are you using a ventilated gas cap?

@mainstreambuilds 11 күн бұрын

@Specer_G Thanks for checking out the channel. So I deleted all yhe charcoal canister stuff and routed the vent line into the chassis where the factory vent line went. I found even the vented gas caps don't work very well

@Specer_G 11 күн бұрын

@@mainstreambuilds I appreciate it! Keep up the good work!

@mainstreambuilds 11 күн бұрын

@Specer_G Thanks man!

@richardrojas5578 Ай бұрын

Hey I was hoping you’d post the templates for the +89 3 piece wing for the mk3 I’d really appreciate it if you made them

@mainstreambuilds Ай бұрын

Yeah I'm still trying to find the best way to do it. I want to make it a e-file so you guys can just print it out. Still in the works and we will get it figured out soon!

@manutechsolutions6247 Ай бұрын

Fu*# dude, I try and try and look forward to your videos, but every time it's way too much commentary and not enough work being shown. The videos are 80/20. 80 percent talk, 20 or 15% work. I hope your getting some kick back for sponsorship

@mainstreambuilds Ай бұрын

Totally understand man! I really don't want my videos to turn people away. What would you like to see more of??

@manutechsolutions6247 Ай бұрын

@@mainstreambuilds more work, less talk. If you're in it for views and really want your channel to be successful, buy some gaskets and do it over. Should be pretty easy since you already done it before and figured out the problems that viewers will come across with 7M's. Otherwise there's plenty of channels on KZfaq that are actually getting down and not just throwing shots out to companies. I like you because you're a real 7mgte enthusiast regardless if you started with a N/A, but I will tell you that when start talking, and keep talking and there's nothing but small work to follow, people will bounce to other channels that's really getting down. At least show your viewers that you have rip that thing. Send it one time. Damn. Something to keep your viewers excited for the next videos and inspiration. Hello

@mainstreambuilds Ай бұрын

@manutechsolutions6247 thanks for the feedback.

@manutechsolutions6247 Ай бұрын

Your catch can video was catch and bait. Nothing 😞 just talk. Very disappointing

@mainstreambuilds Ай бұрын

Totally get it man! It's hard doing videos on stuff I've already done to the car. I want to do a lot more just not sure what viewers are after.