SOMETIMES YOU MAY EXPERIENCE REPEATED 3RD CLUTCH FAILURE ON THESE UNITS. THIS IS ONE OF THE MANY REASONS YOU WILL EXPERIENCE THAT ISSUE IF NOT CORRECTED.
Пікірлер: 51
@nyertsenginetransmission38612 жыл бұрын
Can never learn enough! Have been following you for years n have learned alot thanks for your time and videos
@Roscotech6 ай бұрын
Thanks Hiram, I actually found one leaking (input drum shaft) on the 60 I am building now. I have the same blow gun and put the tip through the exit hole inside the drum (all the pistons were out) for 3/4 then blocked the apply hole in the shaft. I used brake clean in the bearing/shim pocket and then applied pressure. Only tiny bubbles but have been told that can get worse with temperature. Going to press the shaft out and reseal tomorrow. This is just what I needed to see.
@renesanchez31712 жыл бұрын
Saludos maestro desde El Salvador,me gusta ver sus videos,aprendo mucho,gracias por su aporte sin egoísmos.lo felicito por compartir su sabiduría.
@AutomaticTransmission2 жыл бұрын
Saludos El Salvador.
@mag1vl2 жыл бұрын
Hello Hiram from Australia ;) Many thanks and yes you keep building them and I'll keep watching..
@AutomaticTransmission2 жыл бұрын
Hello Australia
@jaimevela8782 жыл бұрын
Buenos días profesor Hiram Aquí en mi localidad a las camionetas silverados se les queman mucho los de la sección de arranque o 3-4 y batallo mucho con esos discos aún cambiando bujes pero tendré más cuidado checando así como nos enseña usted gracias profesor Hiram saludos desde México Veracruz
@AutomaticTransmission2 жыл бұрын
Saludos
@josephadedjumoh69222 жыл бұрын
Greath thanks for the good teaching to the entire world. Thank Sir
@SkubaSam Жыл бұрын
Is there any follow up to how to jb weld the shaft in?
@josephadedjumoh69222 жыл бұрын
SIR wit all due respect YOU are an excellent master. I gained more then a lot from ur teaching may God Almighty stand to help ur children as well as u've ur time to me this. Am very happy Sir
@AutomaticTransmission2 жыл бұрын
Thank you
@MitzvosGolem12 жыл бұрын
Excellent videos Thank you . I have a 1500 Express 4.3 van. Now torque converter shudder. Orherwise good at 350,000 miles hauling tools equip.
@AutomaticTransmission2 жыл бұрын
Look for the P1870 video I have on the channel. There's 2, one early and one late. Yours is the late. Do the valve flip to make it on/off instead of PWM. If shudder goes away you'll be okay. If still there then converter clutch is already gone. Which is normal wear and tear.
@MitzvosGolem12 жыл бұрын
@@AutomaticTransmissionThanks. Shudder only happens 50-65 mph light load goes away when under load so tcc clutch is prob ok? Just dropped pan oil clean changed twice a year spotless no debris .Thanks for helping.
@TAShannon1 Жыл бұрын
Thanks for the video. I just put together an input drum with sonnax sleeve, sonnax billet overrun, sonnax fwd piston sonnax input the whole 9 yards and was getting leaks on all ports.... disassembled and reassembled 3 times... turns out the air was leaking back past the rubber on my nozzle 🫤 😤
@AutomaticTransmission Жыл бұрын
Nice work!
@TAShannon1 Жыл бұрын
@@AutomaticTransmission haha yeah thanks. 😆
@DrFiero2 жыл бұрын
I just "Hiramed" one of my flat blades (with a notch in it). It makes it SO much easier to get the big lock rings out!!! :D
@billk57272 жыл бұрын
Good information Hiram!! Thanks a million! Bill
@mrwhite26282 жыл бұрын
Good video Hiram! I like to see how others do things. It doesn't matter how long you've been at it. You never know what you might pick up. The only thing I disagree with. Is I would never use that drum that had the big leak in it. Sealing on a bench with JB weld is quite different that a drum is under a constant torque load. Although it work out just fine. That is a risk I would be wiling to take. Drums are cheaper than comebacks. Keep up the good work!
@AutomaticTransmission2 жыл бұрын
Yeah, that drum I probably won't use. The replacement drum looked a little gray but wasn't leaking. I still do the same procedure eventhoug the drums don't leak.I used to use red loctite but opted to use JB Weld instead. The JB Quick also works but not too fond of it. At least not for this.
@corbettknowles99422 жыл бұрын
@@AutomaticTransmission although I prefer to replace the drums when they're like that I have to agree with your assessment the J-B Weld Repair does work but also know that Transtar sells a repair kit for those upfront input drums where the shaft likes strip out the hole I believe it us called front input drum saver
@paxtonspeed6 ай бұрын
Good video, never seen this one before.
@FreeFLF9 ай бұрын
Great video! Do you have any videos explaining how to do the repair? Where do you apply the jb weld and how much? Is it on the shaft in the area that goes into the drum and is right above the holes that go into the drum?
@castledomeknives9395 Жыл бұрын
I really dig the JB WELD THING...... BUT won't a Hard launch or linelock break the JB weld "seal" ??
@eulasdubois3181 Жыл бұрын
Love your videos.. Help me out big time. Any video on the shaft repair with jb weld
@oscarxx752 жыл бұрын
Hello hiram from México thanks for tour videos
@AutomaticTransmission2 жыл бұрын
Saludos México.
@b.c6015Күн бұрын
Sonnax told me to use Loctite 609 .... it jb weld good for the vibration
@thurmanjohnson623711 ай бұрын
What if i put air in the 3 rd clutch circuit, but air is leaking out input shaft in side the drum. Do i need a new shaft if not sealing? Let me know. Thanks. Thurman
@41johndeere2 жыл бұрын
Thanks
@AutomaticTransmission2 жыл бұрын
You're welcome
@miguelbadillo6382 Жыл бұрын
Thanks for all the good knowledge. I have a question please. If I buy a 4l60e kit for a 2002 gmc will it fit a 2002 4l65e? Seals, clutches, I know that input shaft is different but are all the other parts the same. Thank you.
@TBD3.0 Жыл бұрын
I wish I knew what compressor he was using with that Sonnex gadget.
@edwardsjohnson53872 жыл бұрын
Great video. I like your old ones also. Question. During air check on 4t65e the top teflon seal has very small leak. It that acceptable or not? Thanks
@gabrielfranjul71719 ай бұрын
The drum must have all the clutches and pistons installed to do this test?
@jeffambrose52445 ай бұрын
Do you test them at operating temp? the aluminum expands faster than the steel shaft
@josephadedjumoh69222 жыл бұрын
I, watch ur very good work from France Beauvais.
@AutomaticTransmission2 жыл бұрын
Hello France
@josephadedjumoh69222 жыл бұрын
@@AutomaticTransmission Am fine sir,
@josephadedjumoh69222 жыл бұрын
Sir kindly and please O need ur help about auto transmissions gearbox manual book. Kindly help me and how I can get it and how much it will cost. Thanks Sir
@STEVEEDG10 ай бұрын
I think I broke mine with a higher stall converter what parts/kit do you recommend that will last longer than stock parts?
@miguelbaldiviezo1446 Жыл бұрын
Gracias... Muy valiosa información
@martinez1701a Жыл бұрын
So when do you wanna save a input drum? I have a drum with a small leak when I air checked it, the shaft has no play and seems ok.
@leonardlawson4354 Жыл бұрын
Thank you for the info
@AdalbertoVALENCIA-hq8pr8 ай бұрын
Sonaxx said if is lower than 15 that's an issue!!!
@leonardlawson4354 Жыл бұрын
I wish you would do à valve body vidéo on a 4l60e
@jackmahle8680 Жыл бұрын
where can one get that pressure test tool✌
@josephadedjumoh69222 жыл бұрын
Hellow master Hiram, pls need the manual books of automatic transmission gearbox. Kindly help me through