4L60E Rebuilding Particulars

Рет қаралды 12,865

Күн бұрын

This video is part of a five part series covering the 4L60E. In this video, I cover issues that often arise when overhauling this transmission. I address some of the most common questions and confusions that come up in my automatic transmissions class.

Пікірлер: 18

@erickenner4847 Жыл бұрын

Thank you for producing this video, I’ve rebuilt at least 20 of these but it’s been about 6 years ago and I really needed a refresher course 😀😀👍

@stevenbailey9170 Жыл бұрын

Very helpful

@victorthecarguy3126 Ай бұрын

Great video, thanks for the tips. It's nice to hear someone call it a pump without saying "front" how many pumps do these guys think they have in a transmission?

@papergatorzfedducca7998 2 жыл бұрын

🔥🔥🔥🔥

@humbertoramirez7799 Жыл бұрын

thank you for good video

@randy1ization Жыл бұрын

to measure servo pin travel, with everything assembled, get u an old servo cover, grind the middle part out, then reinstall it. you can them take a screwdriver and push the servo pin in, and see how far it travel to engage the band.

@mafosa8519 3 жыл бұрын

dude!!! this really good stuff here!.. thanks for taking the time to do it! one question . on the servo clearance. can i just use a cheater spring inside the assembly? just to make it easier to compress? and did you use the servo seals during the check? thanks!! larry

@siuautomotive 3 жыл бұрын

No problem! It's fun to do. I assume you're talking about checking the servo assembly without the special tool and just prying on the cover when installing it. You could use a cheater spring, just be sure that you don't forget to put the correct one in :). I had the servo seals installed because I wasn't planning on taking it back out after I installed it, since it checked out fine.

@darylvoorhees2629 6 ай бұрын

I was hoping you would have talked about the check balls in the valve body @34:36 I'm concerned that there are the crrect check balls in their proper location on the VB side and the CA side of the valve body plate.

@purityobot5390 Жыл бұрын

Please I want to know if the 4L60E 4x4 Tail Output Shaft turns anticlockwise only

@papergatorzfedducca7998 2 жыл бұрын

What year 4l60e does this apply to?

@RicardoGonzalez-jr3wp 3 жыл бұрын

What part of the five part series is this?

@siuautomotive 3 жыл бұрын

You can see how these videos are laid out at www.automotivetextbook.com/automatic-transmission-curriculum/

@gilbertorodriguez8847 Жыл бұрын

I installed the after market case saver. Will misinstallation case a 3-2 downshift shudder?

@siuautomotive Жыл бұрын

It shouldn’t. The case saver is to prevent the case from getting beat up in the 2-1 or 3-1 downshift. Was anything else done to it?

@gilbertorodriguez8847 Жыл бұрын

@@siuautomotive 2007 Chevy Suburban 4l60e rebuild. No mods other than the aftermarket case saver. Getting a down shift shudder to 1st. No codes

@siuautomotive Жыл бұрын

That’s odd, because the only thing that happens during the 2-1 downshift is the band releases and the one-way roller holds.

@gilbertorodriguez8847 Жыл бұрын

@@siuautomotive Put it on the lift , got it to 4th ,then slowed down to down shift. got to 20 mph and the shudder started. end up being the passenger side motor mount, Sir. Thank you for your help, Sir