Autool CT400 - 2.0 FSI GDI Injectors

No video

Autool CT400 - 2.0 FSI GDI Injectors

Рет қаралды 16,224

Күн бұрын

Set of VW/Audi 2.0 FSI injectors (non turbo) sent in for testing due to rough running and occasional misfiring on a customers recently purchased vehicle.
Initially, injector three was blocked so with that cleared all four were flowing.
Back on to flow testing it was evident injector 1 was producing far more than the other three, ummmmm.
With little investigation it was clear someone had previously changed out the original injector and replaced it with one from a TFSI (turbo variant).
Here’s a short vid showing them on the machine.

Пікірлер: 36

@AUTOOLTECH Жыл бұрын

Cool, I'm glad our products helped you and you shared them

@246alfa 8 ай бұрын

Ваши продукты очень помогают мне. Спасибо. После таких приборов приходится все переделывать.

@user-qb7we8ol6m 5 ай бұрын

That is really incredible

@lemanslemans1460 Жыл бұрын

hi,ican see very well how you conected the GDI inyectors

@jaaattengineering8940 Жыл бұрын

With the unit comes some leads with small spade terminals that can be used

@HeBeOhe Жыл бұрын

Do you recommend this tester or are there any better like launch or powerjet ?

@jaaattengineering8940 Жыл бұрын

For me yes this is great. ASNU I believe is the top brand to have but of course at top brand money. I’m very happy with my machine though.

@menelaos1992 Жыл бұрын

I measured mine injectors and 1/4 had 3cc deviation from the test at 10bar after cleaning. Is it ok?

@jaaattengineering8940 Жыл бұрын

Ideally they’d match across all injectors but should be ok. I’ve seen worse.

@adammcalpine231 Жыл бұрын

How do you know which voltage to set the machine at? The 12v, 70v, or 120v selector.

@jaaattengineering8940 Жыл бұрын

12V is normal style injector, 70 or 120 is GDI so you need to check the manufacture specs, or just start at 70 with all GDI and if no go then you know 120 is needed 😉

@HeBeOhe Жыл бұрын

Can this machine test low impedance (1-2 Ohm) injectors proberly ?

@jaaattengineering8940 Жыл бұрын

Apart from side feed injectors, I’ve not experienced any issues testing injectors with this machine 👍🏽

@TheDevin918 Жыл бұрын

How much do you charge to service a set of 4?

@jaaattengineering8940 Жыл бұрын

Pricing is listed on the website on the following link - jaaattengineering.co.uk/online-store/ols/products/fuel-injector-testing-cleaning-service

@elpanchomaga Жыл бұрын

How you know the voltage?

@jaaattengineering8940 Жыл бұрын

Normal rail fed injectors are 12v GDI can be either of the two higher voltage, if you don’t know, start with the lower voltage but you should research the injector so you know for sure 👍🏽

@OmarLopezAguirre Жыл бұрын

Hello! How is it working so far ?

@jaaattengineering8940 Жыл бұрын

Working good. Done many injectors with the machine 👍🏽

@OmarLopezAguirre Жыл бұрын

That’s awesome! Thank you for your reply. I also wanted to ask you if you don’t mind. Are you able to test and clean side feed injectors and Vortec with this machine ?

@Oldiebursch Жыл бұрын

Can you tell me what fluid you use on the valve test?

@jaaattengineering8940 Жыл бұрын

Sure. White sprits for injector testing and ultrasonic cleaning solution for cleaning them.

@ygoilclub40 Жыл бұрын

Please tell me the fluid for injector test. Please also send me the product picture. Thank you

@jaaattengineering8940 Жыл бұрын

@@ygoilclub40 White sprits for injector testing and ultrasonic cleaning solution for cleaning them. Just search the internet for these items and choose the brand you’re happy with

@ygoilclub40 Жыл бұрын

@@jaaattengineering8940 감사합니다